User Manual
4
MODE 1 MODE 2
1) Page Up 1) 3
2) Page Down 2) ;
3) Left Arrow 3) P
4) Right Arrow 4) Shift + R
5) Enter 5) Space
6) b 6) Ctrl + Z
MODE 3 MODE 4
1) Up Arrow 1) F9
2) Down Arrow 2) F7
3) Left Arrow 3) F4
4) Right Arrow 4) Ctrl + Shift + T
5) Enter 5) F8
6) b 6) F3
MODE 5 MODE 6
1) Volume Up/Camera 1) Space
2) Volume Down 2) Enter
3) Previous Song 3) 1
4) Next Song 4) 2
5) Play/Pause 5) Home (iPad)
6) Home (iPad) 6)Virtual Keyboard
CHANGING THE MODE
1. Turn on the STOMP 6.
2. Press and hold the Switch 6 for 2 seconds. The LED will flash red once
per second from 1 to 6 flashes. The number of flashes corresponds to the
same MODE number. Be sure to count the flashes.
3. Release Switch 6 following the number of flashes that reflects the desired
MODE. The orange LED will flash the number of times indicating which
MODE has been set.
Example: To set MODE 3 hold Switch 6 for 3 flashes of the red LED, release
and the orange LED will flash 2 times to confirm the MODE 2 setting.
Note: Once the MODE has been set, it will remain the same until it is changed
following the above steps.
KEY REPEAT FUNCTION
To turn on the Key Repeat function, hold down switches 2 and 4 together. Once
you have turned it on, holding down a pedal or button, (except button 6) in any
MODE for more than two seconds will repeat the key action twice per second
5
until released. Variances may occur in the repeat timing due to environmental
factors.
IOS VIRTUAL KEYBOARD
Some applications require the use of the keyboard to enter text or to interact with
the application. Since the STOMP 6 is an external keyboard, the iPad or other iOS
device by default disables its own virtual keyboard.
To display the virtual keyboard, open any text box on the iPad, then tap in the text
box to activate the cursor. Then, quickly press and release the power switch while
the STOMP 6 is connected to the iPad. If you close the virtual keyboard from
within the application, you can press the power switch again to reactivate it. This
is a toggle switch so pressing it will toggle the virtual keyboard on and off. Note
that iPhones may require toggling on the keyboard for each use.
TROUBLESHOOTING
STOMP 6 IS NOT CONNECTING OR PAIRING
1. Delete the AirTurn device on your host computer. On an iOS device, go to the
Bluetooth settings, (Settings>General> Bluetooth), and press the “i” in the circle
next to the AirTurn selection and then press the Forget this Device button, then
OK.
2. Turn off Bluetooth on the host device.
3. Hold the power button on the STOMP 6 for 8 seconds until you see the LED
light blink red/green rapidly several times.
4. Turn on the STOMP 6
5. Turn on Bluetooth on the host device.
6. The STOMP 6 should appear after 5-9 seconds depending on the host.
7. Touch or click the listing when it appears and it will connect after another few
seconds.
STOMP 6 IS CONNECTED BUT NOT WORKING
1. Check the Mode. To change the mode to the default mode 3, hold down button
6 until the red led blinks 3 times and release.
2. Make sure you are using an app that supports the STOMP 6. (Check the AirTurn
website. http://airturn.com/apps)
3. Check the application instructions to make sure you have the application set up
for the AirTurn.
4. On an iOS device be sure you are not running too many applications. See your
iOS instructions for closing apps.