User Guide PCT Multi Touch Monitor Display OF17T100-A1-PCT American Industrial Systems - OF17T100-A1-PCT User Guide Page 1
The information contained in this document is subject to change without notice. This document contains proprietary information that is protected by copyright © 2013 American Industrial Systems. All rights are reserved. No part of this document may be reproduced, translated to another language or stored in a retrieval system, or transmitted by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission. Windows is a registered trademark of Microsoft, Inc.
Table of Contents Introduction .................................................................................................................................................. 5 About OF17T100-A1-PCT .......................................................................................................................... 5 Touch Screen for OF17T100-A1-PCT............................................................................................................... 6 Package Overview ......................
Usage Notice Warning! ! To prevent the risk of fire or shock hazards, do not expose this product to rain or moisture. Do not open or disassemble the product as this may cause electrical shock. Precautions Follow all warnings, precautions and maintenance as recommended in this user’s manual to maximize the life of your unit. Do: • • • • Turn off the product before cleaning.
Introduction About OF17T100-A1-PCT OF = Open frame R = Regular width ratio of 4:3 17 = Diagonal viewing area in inches PCT = Projected Capacitive Touch The monitor has a flat panel screen with an active matrix, thin-film transistor (TFT) liquid crystal display (LCD). Features include: • • • • • • • • • • • • • Direct Analog signal input Active matrix TFT LCD technology 1280 x 1024 XGA resolution 17" viewable display area 31.47 ~ 80 KHz horizontal scan 56 ~ 75 Hz high refresh rate 0.264mm x 0.
Touch Screen for OF17T100-A1-PCT • • • • • • Projected capacitive touch screen for finger input only Surface: Glare treatment Interface: USB controller Transmittance: 90±5% HID: Windows® 7 Driver: VISTA, XP, 2000, CE, XP Embedded, Linux, Apple® Mac OS American Industrial Systems - OF17T100-A1-PCT User Guide Page 6
Package Overview American Industrial Systems - OF17T100-A1-PCT User Guide Page 7
Installation Product Overview Front View Bottom View American Industrial Systems - OF17T100-A1-PCT User Guide Page 8
Attaching the Side Brackets Depending on your mounting scheme, alternately, you may use the side brackets to mount your displays onto your wall or device. Find a suitable location for attaching side brackets. A. The left and right sides B. The Top and bottom sides Note: You will need a screwdriver to attach the side brackets. Your kiosk touch monitor included 4 side brackets (R/C/W x2, P-Cap x4) and 8 screws, M4x6 (R/C/W x4, P-Cap x8).
Side mount for Your Monitor This monitor can be mounted to the wooden or concrete wall with 4 screws and a pair brackets on the opposites.
Cut-Out Dimensions American Industrial Systems - OF17T100-A1-PCT User Guide Page 11
Connecting the Display To setup this display, please refer to the following figure and procedures. 1. Be sure all equipment is turned off. 2. Connect the DC adapter to the power connector on the monitor and the other end into an electrical outlet. 3. Connect the D-SUB cable from the display’s VGA input connector to the D-SUB connector of your host computer and tighten the screws. 4. Connect the RS-232 or USB cable from the RS-232 or USB port of your display to the RS-232 port or USB port of your computer.
User Controls Back Panel Controls American Industrial Systems - OF17T100-A1-PCT User Guide Page 13
How to Use the OSD Menus 1. Press the “MENU” button to pop up the “on-screen menu” and press “Up” or “Down” button to select among the five functions in the main menus. 2. Choose the adjustment items by pressing the “Enter ” button. 3. Adjust the value of the adjustment items by pressing the “Up” or “Down” button. 4. With the OSD menu on screen, press “ Menu” button to return main menu or exit OSD. 5. The OSD menu will automatically close, if you have left it idle for a pre-set time. 6.
On-Screen Display Menus Main OSD Menu: American Industrial Systems - OF17T100-A1-PCT User Guide Page 15
Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. If the problem persists, please contact your local dealer or our service center. Problem: No image appears on screen Check that all the I/O and power connectors are correctly and well-connected as described in the “Installation” section. Make sure the pins of the connectors are not crooked or broken.
Warning Signal If you see warning messages on your LCD screen, this means that the LCD display cannot receive a clean signal from the computer graphics card. Below are the three kinds of Warning Signal. Please check the cable connections or contact your local dealer or our service center for more information. No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics card.
Product Dimension American Industrial Systems - OF17T100-A1-PCT User Guide Page 18
Compatibility Modes American Industrial Systems - OF17T100-A1-PCT User Guide Page 19
Touch Screen Driver Installation The monitor is available with USB connection. The Linux kernel 2.6.x (32 bit & 64 bit) touch driver is located on the enclosed CD-ROM. HID for Windows® 7, VISTA , XP, 2000, ME, 98. Please Note: The system requires 15 seconds for Windows® 7 to install/uninstall the touch drivers while turning power on/off or plugging/unplugging USB cable. Driver Install Instructions: If you are using a PC running driver Linux kernel 2.6.x (32 bit & 64 bit), follow the instructions below: 1.
If you are using a PC running Linux or Apple® Mac OS, follow the instructions below: 1. Power on the computer. 2. Make sure that the USB cable is connected to the computer. 3. Follow the step-by-step instructions found in the folder file on the CD-ROM.
