AITech ProPC/TV Wireless Mini USER’S MANUAL
FEDERAL COMMUNICATIONS COMMISSION This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions: this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules.
Table of Contents Chapter 1. Overview …………………………………………..................... 1 1.1 : Introduction ………………………………………………………………. 1 1.2 : Features ………………………………………………………………….. 1 1.3 : Specifications …………………………………………………………….. 2 1.4 : System Requirements …………………………………………………… 2 1.5 : Package Contents ……………………………………………………….. 2 Chapter 2. Outline Description ………………………………..……....... 3 Chapter 3. Installation ……………………………….……………………… 5 Chapter 4. Function Description ………………………………………... 7 4.
Chapter 1. Overview 1.1 Introduction AITech’s ProPC/TV Wireless Mini accepts computer signal and convert them into composite video format. With building in 2.4GHz wireless video transmission technology, you can transmit computer VGA signal to TV simply via wireless.
Chapter 1. Overview 1.3 Specifications - - - 1.4 Transmitter - Input: VGA signal (from computer); Stereo audio jack (from computer); RCA video/audio jack (Yellow/Red/White) - Output: Computer monitor pass-thru; 2.4GHz wireless signal (Antenna) - Power in: 5V/650mA - Dimension (mm): 150 x 87 x 25 Receiver - Input: 2.4 GHz wireless signal (Antenna) - Output: RCA video/audio jack (Yellow/Red/White) - Power in: 6V/300mA - Dimension (mm): 110 x 92 x 25 Horizontal frequency: 31.469 KHz – 91.
Chapter 2.
Chapter 2. Outline Description Transmitter 1. PAL/NTSC : TV system select 2. Monitor : Connect to PC monitor 3. VGA in : VGA signal from PC 4. Line in : Audio from PC 5. DC 5V: power in 6. A-IN : Audio in from external video device (e.g. DVD player) 7. V-IN : video in from external video device (e.g. DVD player) 8. AV / PC switch : Select transmitter input source (e.g. PC or DVD player) 9. Power switch : Power ON/OFF PCTVsender 10.
Chapter 3. Installation NOTE: Make sure “PCTVsender”, Computer and TV are all power off before installation 3.1 Transmitter connection: 3.1.1 Connect Antenna to “ANT” of Transmitter 3.1.2 Steps for VGA to TV function as below 1. Properly connect the 15-pin HD extension VGA cable between VGA port (Computer) and “VGA IN” (PCTVsender) input port. 2. Connect PC monitor cable to “Monitor” (PCTVsender) output port. 3. Connect the 3.5mm x 3.
Chapter 3. Installation After connection 3.3 Push the “ON/OFF” power button. (ProPC/TV Wireless Mini transmitter and receiver) to “ON” status. 3.4 Set the channel by pressing the select button on the top of the transmitter and the receiver to the same channel. 3.5 Push the transmitter “PC/AV” button to change the signal input between PC or external device. (e.g. DVD player) 3.6 Turn on both computer (or DVD player) and TV. 3.7 Now the video showed on PC monitor or external device (e.g.
Chapter 4. Function Description Note : The following adjustments is for VGA to TV mode settings only. 4.1 Horizontal/Vertical position : Press [ / ] to adjust TV vertical position. Press [⊳ ⊳ / ] to adjust TV horizontal position. 4.
Chapter 4. Function Description 4.3 HSIZE : - Controls the horizontal scaling: - Press [ M ] to bring up the OSD menu. - Press [ / ] to scroll to HSIZE function. - Press [ ] to increase horizontal dimension. - Press [⊳ ⊳ ] to decrease horizontal dimension. - To exit HSIZE control, press [ M ] again 4.4 VSIZE : - Controls the vertical scaling: - Press [ M ] to bring up the OSD menu. - Press [ / ] to scroll to VSIZE function. - Press [ ] to increase vertical dimension.
Chapter 4. Function Description 4.6 CONTRAST : - Controls the contrast level of the display - Press [ M ] to bring up the OSD menu. - Press [ / ] to scroll to the CONTRAST function. - Press [ ] to increase the contrast level. - Press [⊳ ⊳ ] to decrease contrast level - To exit contrast control, press [ M ] again 4.7 SHARPNESS : - Controls the sharpness level of the display - Press [ M ] to bring up the OSD menu. - Press [ / ] to scroll to SHARPNESS function.
Chapter 4. Function Description 4.9 NORMAL / ZOOM : - Switches between normal mode and zoom mode. - In Zoom mode, the picture is zoomed in at the scale of 9x. - Press [ M ] to bring up the OSD menu. - Press [ / ] to scroll to NORMAL ZOOM function. - Press [⊳ ⊳ / ] switches between the normal mode and zoom mode. - Once in zoom mode, Press [ / ] to adjust vertical position. - Press [⊳ ⊳ / ] to adjust horizontal position. 4.10 FREEZE / UN-FREEZE : - Switches between pause mode and play mode.
Chapter 5. Troubleshooting Q1 : Poor signal, or there is an interference A1 : (1) Adjust the transmitter by rotating orientations until you get the best reception (2) Change the channel on both transmitter and receiver. (Please make sure that they are on the same channel) (3) If there is a microwave oven in use in the path between the transmitter and receiver, remove the microwave oven or turn it off. (4) Make sure the transmitter and receiver are within range of each other.
Chapter 5. Troubleshooting Q4 : Just mono (black/white) display on TV A4 : Switch “NTSC/PAL” switch to match TV system. Q5 : I found line flicker on TV screen A5 : (1) Please adjust “FLICKER” (see 4.11) (2) Please lower the contrast level and higher the brightness level which will minimize the flicker.
