OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES MODE D’EMPLOI ADC-M105 YU COMPACT DISC CHANGER CAMBIADOR DE DISCOS COMPACTOS ENGLISH ESPAÑOL FRANÇAIS OWNER’S RECORD For your convenience, record the model number and serial number (you will find them on the rear of your set) in the space provided below. Please refer to them when you contact your AIWA dealer in case of difficulty. Model No. ADC-M105 Serial No. 8Z-KM3-922-01 001110ATM-OX 00ADCM105.YU.Cov 3 01.1.
Welcome Thank you for your purchasing this AIWA product. To optimize the performance of this unit, please read through this manual carefully. TABLE OF CONTENTS FEATURES .......................................................................................................................................... 1 PRECAUTIONS ................................................................................................................................... 2 UNPACKING .............................................
PRECAUTIONS • Do NOT install the unit in a location where it may be subjected to: — Direct sunlight or other sources of excessive heat — Fluid, rain or moisture — Excessive dirt or dust — Excessive vibration • This unit is designed to be operated on a 12-volt DC negative-ground electrical system only. • Choose the mounting location carefully so that the unit will not interfere with normal driving functions. • Before making connections, disconnect the ( terminal of the car battery to avoid short circuiting.
UNPACKING Compact disc changer Compact disc magazine Connecting cable Supplied mounting kit for the compact disc changer The letters are keyed to those in the instructions. Use only the supplied mounting hardware for safe and secure installation. a Brackets (1 pair) b Washer screws (4 ea.) c Plate brackets (2 ea.) d Nuts (4 ea.) e Adhesive label (1 sheet) 3 ENGLISH 01ADCM105.YU.E 4 01.1.
INSTALLATIONS Precautions Mounting angle setting levers Select the mounting location very carefully, referring to the following points. Be sure to change the position of both mounting angle setting levers according to the angle at which the unit is to be installed. • Make sure that there is no fuel tank, wiring or piping on the other side of the mounting surface. • Make sure that the installation of the unit will not hinder the movement of the deck lid or interfere with the spare tire, etc.
INSTALLATIONS Horizontal installation 1 Construction For details on abc..., see page 3. The effective angle of the unit. ; ; ; ; ; ; ; ;; The position of the lever. Note If the mounting surface needs to be strengthened, secure the plate brackets c to the bottom surface of the car trunk, etc. with the tapping screws (not supplied).
Vertical installation 1 Construction For details on abc..., see page 3. The effective angle of the unit. The position of the lever. ; ; ; ; ;; Notes • If the mounting surface needs to be strengthened, secure the plate brackets c to the bottom surface of the car trunk, etc. with the tapping screws (not supplied). • If installation space is narrow, bend the plate bracket c back and forth along the perforated line to break off the end.
INSTALLATIONS Suspended installation Caution When installing the unit in the trunk below the package tray, observe the following. • Select the mounting location carefully so that the unit does not hinder the movement of the torsion bars of the deck lid. Before drilling the holes, make sure that there is nothing on the other side of the mounting surface. 1 Construction For details on abc..., see page 3. The effective angle of the unit. The position of the lever.
CONNECTIONS This unit is designed only for AIWA brand car stereo. Therefore you cannot use the unit with other brand’s equipment. Compact disc changer Connecting cable (supplied) to AIWA brand car stereo Caution Note Be sure to disconnect the ground wire terminal of the car battery before making a connection in order to prevent short circuiting. Use only the supplied connecting cable. Using an unspecified connecting cable may cause background noise. ENGLISH 01ADCM105.YU.E 9 01.1.
HOW TO USE How to use a compact disc magazine 1 With the label side up, insert a disc all the way. Labeled side 10 discs, one in each disc tray Recorded side To remove a disc, pull part A in the direction of the arrow as illustrated. 2 Open the door. 3 Disc magazine Insert the magazine (which has been taken mark visible out of the unit) firmly with the on the top side. z (eject) button To remove the magazine, press the z button and pull out the disc magazine. 4 Close the door.
SPECIFICATIONS Notes on the disc magazine Compact disc changer • Be sure to place a disc on the disc tray with the label side up. If a disc is not set properly, it may cause damage to the unit. System Disc magazine Frequency response Wow and flutter Signal to noise ratio Outputs Compact disc digital audio system 5 Hz – 20 kHz Below measurable limit 91 dB or more Line output (for changer connector only) Operating temperature –10 °C to 55 °C 254 × 83 × 173 mm (w/h/d) (10 × 3 3/8 × 6 7/8 in.) Weight 2.
Printed in Indonesia 00ADCM105.YU.Cov 2 01.1.
