CSD-MD50 EZ SERVICE MANUAL MD/CD STEREO RADIO CASSETTE RECORDER BASIC TAPE MECHANISM : 2ZM-1R7 BASIC MD MECHANISM : 7ZG-9B2 BASIC CD MECHANISM : 3ZG-3E2 S/M Code No.
TABLE OF CONTENTS SPECIFICATIONS .................................................................................................................................. 3 ACCESSORIES/PACKAGE LIST ........................................................................................................... 3 PROTECTION OF EYES FROM LASER BEAM DURING SERVICING ................................................ 4 Precaution to replace Optical block.........................................................................
SPECIFICATIONS • • • ACCESSORIES/PACKAGE LIST REF. NO ! 1 2 3 4 PART NO. KANRI DESCRIPTION NO. 8Z-CK4-952-010 RC UNIT,RC-ZAT04 8Z-CK3-906-010 IB,EZ(9L)I 87-006-240-010 AM LOOP ANT CON(KO) 87-A80-081-010 AC CORD SET ASSY,EZ BLK 3 Design and specifications are subject to change without notice. Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.
PROTECTION OF EYES FROM LASER BEAM DURING SERVICING This set employs laser. Therefore, be sure to follow carefully the instructions below when servicing. CAUTION Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. WARNING! WHEN SERVICING, DO NOT APPROACH THE LASER EXIT WITH THE EYE TOO CLOSELY. IN CASE IT IS NECESSARY TO CONFIRM LASER BEAM EMISSION.
Precaution to replace Optical block (KSS-213F) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode. 1) After the connection, remove solder shown in the right figure. Precaution to replace Optical block (KMS-260A) Body or clothes electrostatic potential could ruin laser diode in the optical block. Be sure ground body and workbench, and use care the clothes do not touch the diode.
DISASSEMBLY INSTRUCTIONS Disassembling Procedure 1. Remove the seven screws (A BVT2+3-18*7) and remove the rear cabinet. A 2. Remove the two screws (B BVT2+3-12*2). Remove the MAIN C.B by pulling it upward. B 3. Remove the four screws (C BVT2+3-12*4).
4. Open the deck lid. Release the two claws 1 and remove the PANEL DISP by pulling it upward. 1 1 1 1 5. Close the deck lid. Raise the deck block from the rear. 6. Remove the two screws (D BVT2+3-12*2). While raising the MAIN C.B., release the claws starting from 1 to 7, and remove the MICOM/CD C.B.
7. How to remove the COVER, FFC. 1) Remove the five screws (A BVT2+3-12*5) and remove the deck mechanism. A 2) Remove the SPR T CASS from the rib and remove the BOX CASS. 3) Release the two claws of the COVER and FFC by pressing them in the direction of the arrow.
4) Raise the COVER and FFC in the direction of the arrow, and remove them. 8. How to remove FL C.B. 1) Release the two claws 2 and pull the top of the FL C.B. to the front. The FL C.B. can be removed. 2 9. 2 How to remove the CD panel 1) Move the CAM SLIDE by 1 cm to the left. 2) Move down the DRIVE C.B. and establish the “un-chucking” status. 3) Press TRY, CD2 twice.
. Remove the four screws A (S-SCREW, MD) and screws B (BVTT +3-6). Remove the four FFCs from the connector, and remove the MD MECHANISM in the direction of the arrow. (Fig-1) HEAD, OWH RF325-74A D C A C B PLATE ASSY, SIDE L A B PLATE, SIDE R B MD MECHANISM FFC Fig-3 13. Open the 7ZG-3 A2 in the direction of the arrow (a), remove the BOSS by pressing it gently in the direction of the arrow (b), and remove the 7ZG-3 A2 in the direction of the arrow (c).
ELECTRICAL MAIN PARTS LIST REF. NO PART NO. KANRI NO. DESCRIPTION REF.
REF. NO PART NO. C430 C431 C432 C433 C434 KANRI NO. 87-010-405-080 CAP, 87-010-184-080 CHIP 87-010-184-080 CHIP 87-010-406-080 CAP, 87-010-406-080 CAP, DESCRIPTION ELECT 10-50V CAPACITOR 3300P(K) CAPACITOR 3300P(K) ELECT 22-50 ELECT 22-50 C787 C788 C789 C790 C791 KANRI DESCRIPTION NO.
REF. NO PART NO. C315 C316 C317 C321 C322 KANRI DESCRIPTION NO. 87-010-248-080 CAP, ELECT 220-10V 87-010-178-080 CHIP CAP 1000P 87-012-368-080 C-CAP,S 0.1-50 F 87-012-153-080 C-CAP,S 120P-50 CH 87-012-153-080 C-CAP,S 120P-50 CH REF. NO CN302 CN303 CN304 CN306 CN308 KANRI DESCRIPTION NO.
REF. NO PART NO. C339 C340 C341 C342 C343 KANRI NO. 87-012-156-080 C-CAP,S 87-012-156-080 C-CAP,S 87-012-156-080 C-CAP,S 87-012-156-080 C-CAP,S 87-012-156-080 C-CAP,S DESCRIPTION REF. NO PART NO. 220P-50 220P-50 220P-50 220P-50 220P-50 CH CH CH CH CH C218 C219 C220 C221 C222 KANRI DESCRIPTION NO. 87-012-172-080 CAPACITOR CHIP U 10P CH 87-016-296-080 C-CAP,TN 22-4SV(A) 87-010-662-080 C-CAP,E 22-6.3 87-010-831-080 C-CAP,U,0.
TRANSISTOR ILLUSTRATION REF. NO PART NO. C523 C524 C525 C526 C527 KANRI DESCRIPTION NO. 87-010-662-080 C-CAP,E 22-6.3 87-010-662-080 C-CAP,E 22-6.3 87-012-274-080 CHIP CAP,U 1000P-50B 87-012-274-080 CHIP CAP,U 1000P-50B 87-010-661-080 C-CAP,E 10-16 REF. NO C528 C530 C531 C600 C601 87-010-661-080 87-010-831-080 87-010-831-080 87-010-662-080 87-010-779-080 C-CAP,E 10-16 C-CAP,U,0.1-16F C-CAP,U,0.1-16F C-CAP,E 22-6.3 C-CAP,E 100-6.
FL (16-ST-32GNK) GRID ASSIGNMENT/ANODE CONNECTION 17 18
BLOCK DIAGRAM-1 (MAIN) 19 20
BLOCK DIAGRAM-2 (SYSTEM CONTROL) 21 22
BLOCK DIAGRAM-3 (MD) 23 24
WIRING-1 (MAIN) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J K 25 26 13 14
SCHEMATIC DIAGRAM-1 (TUNER) 27 28
SCHEMATIC DIAGRAM-2 (DECK) 29 30
SCHEMATIC DIAGRAM-3 (MAIN) 31 32
WIRING-2 (SYSTEM CONTROL/CD) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J K 33 34 13 14
SCHEMATIC DIAGRAM-4 (SYSTEM CONTROL) 35 36
WIRING-3 (FL/KEY) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J K 37 38 13 14
SCHEMATIC DIAGRAM-5 (CD) 39 40
WIRING-4 (POWER) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J K 41 42 13 14
SCHEMATIC DIAGRAM-6 (FL/KEY/POWER) 43 44
WIRING-5 (MD) 7 6 5 4 3 2 (COMPONENT SIDE) TO/FROM MAIN C.B CN203 45 1 1 A A B B C C D D E E F F G G H H I I J J 2 3 4 5 6 (CONDUCTOR SIDE) TO/FROM MICOM/CD C.
SCHEMATIC DIAGRAM-7 (MD) 47 48
WIRING-6 (MECHANISM) 1 2 3 4 5 6 7 8 9 10 11 12 A B C D E F G H I J TO MICOM/CD C.
TEST MODE 1. CD TEST Mode 1-1. How to Active the CD TEST Mode While pressing the CD 2 button, connect the AC power plug to the power outlet. After the TEST mode is activated, the message “CD TEST” appears on the display and all displays on the FL tubes are turned on. 1-2.
2-2. How to Exit the MD TEST Mode 1) Eject the disc by pressing the “MD EJECT” button or the “VOLUME UP” button. 2) Disconnect the AC power plug from the power outlet, or press the “POWER” button. 2-3. Operation Check Mode 1) Checking activation of the TEST mode Playback system audio circuit can be checked as follows. • Circuit that can be checked ............. DAC, LINE AMP, HEADPHONE AMP • Output level .....................................
2-8. Checking Servo Operation • Checking the focus search and spindle kick: 1 1) When the MD 2 button is pressed while the machine is in the “ALL SV OFF” status without inserting a disc, focus search and spindle kick are performed continuously. The message “FOCUS SRCH” appears on the display. 2) After the check is completed, press the 9 button to show the message “ALL SV OFF” on the display.
3-3. AUTO SEQUENCE Adjustment (EFB/IVR/FOCUS AGC/TRACKING AGC adjustment) Test disc: MDW-60. TGYS-1 When adjusting MO disc 1) Insert the test disc MDW-60. 2) Press the 9 button to display “ALL SV OFF”. 3) When the “EDIT” button is pressed, “AUTO ADJ” is displayed. When the adjustment is completed, “DONE” is displayed. (When “FAILED” appears, it means that the adjustment has failed.) 4) Press 9 button to display “ALL SV OFF”. Note: 1.
10) Press the MD 2 button to display “FOCUS ON!”. 11) Press the “ENTER” to display “ALL SV ON”, and press the “DISP” button to display “Er00**:0000”. Check that the value of ### is “20” or less. 12) After the adjustment is completed, press the 9 button to display “ALL SV OFF”. 3-6. UTOC ERASE Perform the following procedure only when the recorded disc needs to be erased. 1) Insert a disc from which UTOC is going to be erased. 2) Move the pick up to the center with 6 button and 5 button.
ELECTRICAL ADJUSTMENT MAIN C.B (CONDUCTOR SIDE) TP4 FFE801 3 L981 L772 VR770 TP6 TP5 L771 IC771 CN201 2 6 MICOM/CD C.
SFR1 9 R.P.E HEAD 0 0 < TUNER SECTION > 1. AM VT Check Settings: • Test point: TP4 (VT) Method: Set to AM 1611kHz and check that the test point is less than 5.6V. 5. FM Tracking Check Settings: • Test point: J201 (PHONES) Method: Set to FM 98.0MHz and check that the test point is less than 20dBµV. 2. AM IF Adjustment Settings: • Test point: J201 (PHONES) L772 .............................................. 450kHz 6.
PRACTICAL SERVICE FIGURE < CD SECTION > < TUNER SECTION > 8. Tracking Balance Adjustment < FM SECTION > IHF Sensitiviy: (THD 3%) Oscilloscope (DC range) Signal to noise ratio: + TP2 (TB) Distortion: (Input: 54dB) Stereo separation: – TP3 (VREF) Intermediate frequency: 1) Connect an oscilloscope to the test points TP2 (TB) and TP3 (VREF). 2) Turn on the power switch. 3) Insert test disc TCD-782 (YEDS-18) and press the CD PLAY button.
IC DESCRIPTION IC, CXD2652AR Pin No. Pin Name I/O Description 1 MNT0 O Monitor output pin. 2 MNT1 O Monitor output pin. 3 MNT2 O Monitor output pin. 4 MNT3 O Monitor output pin. 5 SWDT I Data input pin for micro-processor serial interface. 6 SCLK I Shift clock input pin for micro-processor serial interface. 7 XLAT I Latch input pin for micro-processor serial interface. Shut down: Latch. 8 SRDT O Data output pin for micro-processor serial interface.
Pin No. Pin Name I/O Description 40 DVSS – Digital GND. 41 XOE O Output enable pin for external DRAM. 42 XCAS O Output CAS for external DRAM. 43 A09 O Output address for external DRAM. 44 XRAS O Output RAS for external DRAM. 45 XWE O Write enable for external DRAM. 46 D1 I/O Data pass for external DRAM. 47 D0 I/O Data pass for external DRAM. 48 D2 I/O Data pass for external DRAM. 49 D3 I/O Data pass for external DRAM.
Pin No. Pin Name I/O Description 80 XLRF O Latch output pin for CXA2523AR control. Shut down: Latch. 81 CKRF O Shift clock output pin for CXA2523AR control. 82 DTRF O Data output pin for CXA2523AR control. 83 APCREF O Reference PWM output pin for laser APC. 84 LDDR O PWM output for laser digital APC. (Not used) 85 TRDR O Tracking servo drive PWM output (–). 86 TFDR O Tracking servo drive PWM output (+). 87 DVDD – Digital power supply.
IC, CXP81952M-547R Pin No. Pin Name I/O Description 1 MCAS – Not used. 2 MRAS – Not used. 3 BUP – Not used. 4 AMUTE O Output AUDIO MUTE signal. 5 ESK O Serial clock output pin for EEPROM interface. 6 EDO O Serial data output pin for EEPROM interface. 7 EDI I Serial data input pin for EEPROM interface. 8 ECS O Output EEPROM chip select signal. 9 NC – Not used. 10 RFLCT I Input terminal for DISC reflection rate detection SW. 11 NC – Not used.
Pin No. Pin Name I/O Description 53 ~ 55 NC – Not used (PLL UP). 56 SLF – Not used (PLL UP). 57 SLR – Not used (PLL UP). 58 TEMP I S-8110AMP OUT signal input pin. 59 MAGIC – Not used (PLL UP). 60 NC – Not used (PLL UP). 61 TEST – Not used (PLL UP). 62 DISCPRO I Input pin for prevention of DISC error erase SW. 63 MNT3 I Monitor signal input pin 3 for CXD2652AR. 64 MNT2 I Monitor signal input pin 2 for CXD2652AR.
IC, CXA2523AR Pin No. Pin Name I/O 1 I I Input "I" RF signal converted to I-V. Description 2 J I Input "J" RF signal converted to I-V. 3 VC O Output voltage for VCC/2. 4 A I Input current for main beam servo signal A. 5 B I Input current for main beam servo signal B. 6 C I Input currentt for main beam servo signal C. 7 D I Input current for main beam servo signal D. 8 E I Input current for side beam servo signal E. 9 F I Input current for side beam servo signal F.
Pin No. Pin Name I/O Description 42 COMPP I User comparator non-inverted input pin. (Connected to GND) 43 ADDC I/O Capacitor connection pin for ADIP amplifier on return circuit. 44 OPO O Output pin for user operational amplifier. (Not used) 45 OPN I Non-inverted input pin for user operational amplifier. 46 RFO O RF amplifier output pin. Check point for eye pattern. 47 MORFI I Input pin where Groove RF signal is AC coupled. 48 MORFO O Output pin for Groove RF signal.
IC, LA9241ML Pin No. Pin Name I/O 1 FIN2 I Description Pin to which external pickup photo diode is connected. RF signal is created by adding with the FIN1 pin signal. FE signal is created by subtracting from the FIN1 pin signal. 2 FIN1 I 3 E I Pin to which external pickup photo diode is connected. Pin to which external pickup photo diode is connected. TE signal is created by subtracting from the F pin signal. 4 F I Pin to which external pickup photo diode is connected.
Pin No. Pin Name I/O 36 TES O 37 HFL O Description Pin from which TES signal is output to DSP. “High Frequency Level” is used to judge whether the main beam position is on top of bit or on top of mirror. 38 SLOF I Sled servo off control input pin. 39, 40 CV–, CV+ I CLV error signal input pin from DSP. 41 RFSM O RF output pin. 42 RFS– I RF gain setting and EFM signal 3T compensation constant setting pin together with RFSM pin.
IC, LC78622ED Pin No. Pin Name I/O 1 DEFI I 2 TAI I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. 3 PDO O Phase comparator output pin to control external VCO. 4 VVSS — 5 ISET I 6 VVDD — 7 FR I 8 VSS — 9 EFMO O 10 EFMIN I 11 TEST2 I Test signal input pin with built-in pull-down resistor. Be sure to connect to 0V. 12, 13 CLV+, CLV– O Disc motor control output. Three level output is possible using command.
Pin No. Pin Name I/O Description 43 XVDD — 44 XOUT O 45 XIN I 46 XVSS — Crystal oscillator GND pin. Be sure to connect to 0V. 47 SBSY O Subcode block sync signal output pin. 48 EFLG O C1, C2, single and dual correction monitoring pin. 49 PW O Subcode P, Q, R, S, T, U and W output pin. 50 SFSY O Subcode frame sync signal output pin. Falls down when subcode enters standby. 51 SBCK I Crystal oscillator power supply pin. Pin to which external 16.
IC, LC875164A Pin No. Pin Name I/O Description 1 MOTOR O Motor control output. “H”: when operating. 2 — O Not used. 3 LA O BH3862FS serial latch output. 4 CL O BH3862FS serial clock output. 5 DA O BH3862FS serial data output. 6 Q-SW O Q-surround control. 7 SHIFT O Clock shift output. 8 ACIN I AC input detection. 9 REMO I Remote control received signal input. 10 RES I Reset input terminal. 11 XT1 I 32.768 kHz OSC input terminal. 12 XT2 O 32.
Pin No. Pin Name I/O Description 40 SK O EEPROM serial clock output. 41 CS O EEPROM chip selection. 42 NC — Not used. 43 POWER O Power regulator control output. 44 +B — Power supply input. 45 GND — GND terminal. 46 — O Not used. 47 CD+B O CD regulator control output. “H”: when operating. 48 TU+B O TU regulator control output. “H”: when operating. 49 CD O CD LED control output. “L”: to turn on the LED. 50 MD O MD LED control output. “L”: to turn on the LED.
IC BLOCK DIAGRAM IC, BA5970FP IC, BA6417F 72
IC, BD7910FV IC, BH3862FS 73
IC, AK4519VF IC, AK93C65AF 74
IC, BA5936 Rog CURRENT DETECTOR TERMINAL IC, LC75710NE 75
IC, TC74HCT7007AF IC, LC72121 VSSX VSSA VDD VSSD 76
IC, MM1454XFBE VCC LIN VREF QF1 QF2 QF3 QF4 QF5 16 15 14 13 12 11 10 9 + – + – QSurround BIAS + – 1 2 3 4 5 6 7 8 RIN PNR B/Q DET QF6 ROUT LOUT GND IC, LA1837NL 77
MECHANICAL PARTS LIST 1/1 REF. NO 1 2 3 4 5 PART NO. KANRI DESCRIPTION NO. 8Z-CK3-007-010 PANEL,CD 8Z-CK3-004-010 PANEL,MD 8Z-CK3-012-010 LENS,SENSOR 8Z-CK3-003-010 PANEL,CONT 8Z-CK3-024-010 LID,MD REF. NO PART NO. 36 37 38 39 40 KANRI DESCRIPTION NO.
MECHANICAL EXPLODED VIEW 1/1 39 52 D 51 I 20 2ZM-1 YR7N 21 C C C 48 G 50 19 44 F C 43 41 47 H 37 F 42 P.C.B 40 7 FL 46 C 49 45 PT1 P.C.B P.C.B 18 c 35 14 24 C C 36 34 16 P.C.B 30 23 11 B P.C.
TAPE MECHANISM EXPLODED VIEW 1/1 14 B 15 30 DECK C.B 49 B 56 A 47 SOL2 16 12 48 13 50 D 17 B C 10 11 36 44 42 9 51 37 41 7 46 A C 18 43 55 19 35 41 F A 4 5 33 45 6 20 22 34 3 21 RELAY C.
TAPE MECHANISM PARTS LIST 1/1 REF. NO 1 2 3 4 5 PART NO. KANRI DESCRIPTION NO. 82-ZM1-327-210 CHAS ASSY,RN 82-ZM1-258-010 SPR-T,PINCH L 82-ZM1-341-010 LVR ASSY,PINCH L 2 82-ZM1-295-310 PLATE ASSY,LINK 82-ZM1-266-110 LVR,DIR REF. NO PART NO. 33 34 35 36 37 KANRI DESCRIPTION NO. 82-ZM1-227-210 LVR,TRIG 82-ZM1-224-410 LVR,FR 86-ZM4-201-010 SPR-E,TRIG 3 82-ZM1-239-010 CAPSTAN 2.2-41.
CD MECHANISM EXPLODED VIEW 1/2 C 17 16 13 CUSH-G, MAIN A 17 C CUSH-G, MAIN A 3ZG2 14 A B 15 11 9 10 7 5 8 B 4 C 6 A D C 2 12 D 3 A MOTOR-2 C.
CD MECHANISM PARTS LIST 1/2 REF. NO 1 2 3 4 5 PART NO. KANRI DESCRIPTION NO. 83-ZG3-224-310 HLDR,M2 83-ZG3-228-610 CHAS,L6 83-ZG3-208-010 PULLEY,MOTOR 83-ZG3-213-010 LVR,SW 83-ZG3-209-610 CAM,SLIDE 6 7 8 9 10 83-ZG3-207-010 83-ZG3-204-210 83-ZG3-205-010 83-ZG3-217-010 83-ZG3-220-210 GEAR,TRAY GEAR,C GEAR,D S-SCREW,GEAR D GEAR,PULLEY 2 11 12 13 14 15 83-ZG3-214-010 83-ZG3-229-410 83-ZG3-210-110 83-ZG3-602-010 83-ZG3-212-010 BELT,L TRAY,CD 2 HLDR,CHUCK RING,MAG CAP,DISC REF. NO 16 17 A B C PART NO.
CD MECHANISM EXPLODED VIEW 2/2 11 12 8 2 6 A A A A 1 5 3 SW1 4 M20 M21 DRIVE C.B CD MECHANISM PARTS LIST 2/2 REF. NO PART NO. KANRI NO.
MD MECHANISM EXPLODED VIEW 1/3 B B HLDR,SHLD TOP 3 1 CUSH-R,MECHA RE A A 7ZG-8 A2 CUSH-R,MECHA FR A A CUSH-R,MECHA RE 2 CUSH-R,MECHA FR C C P.C.B HLDR,SHLD BOT MD MECHANISM PARTS LIST 1/3 REF. NO 1 2 3 A B PART NO. 87-ZG9-602-010 87-ZG9-603-010 87-ZG9-604-010 87-ZG9-209-010 87-067-020-010 C 87-067-421-010 KANRI NO. DESCRIPTION FF-CABLE,21P 0.5 90MM FF-CABLE,8P 1.0 120MM FF-CABLE,5P 1.
MD MECHANISM EXPLODED VIEW 2/3 E 21 D 20 19 a 18 17 16 13 15 14 C 12 11 B 9 10 8 a 7 5 A 6 3 2 4 1 PCB 7ZG-3 A2 88
MD MECHANISM PARTS LIST 2/3 REF. NO 1 2 3 4 5 PART NO. KANRI DESCRIPTION NO.
MD MECHANISM EXPLODED VIEW 3/3 6 11 H PLATE,YOKE D 5 C 10 HLDR LED 8 4 GEAR, LEAD 3 7 2 9 A 17 B 1 12 16 15 13 14 E A P.C.
MD MECHANISM PARTS LIST 3/3 REF. NO 1 2 3 4 5 PART NO. KANRI DESCRIPTION NO. 87-ZG3-202-510 CHAS ASSY,OUT-SERT 87-ZG3-214-210 SPR-T,SPINDLE-A 83-ZG5-308-010 BRG,1.
SPRING APPLICATION POSITION 82-ZM1-257-010 SPR-T,CAS 82-ZM1-218-010 SPR-E,HB 82-ZM1-285-410 SPR-C,BT L 82-ZM1-244-010 SPR-C,BT 82-ZM3-323-010 SPR-T,LINK 82-ZM1-259-110 SPR-T,PINCH R 82-ZM1-258-110 SPR-T,PINCH L 82-ZM1-269-010 SPR-T,BRG 82-ZM1-213-010 SPR-T,HEAD 82-ZM1-322-010 SPR-T,FR 60 86-ZM4-201-010 SPR-E,TRIG 3 82-ZM1-255-310 SPR-E,LER DIR 92 82-ZM1-214-010 SPR-T,DIR
REFERENCE NAME LIST ELECTRICAL SECTION MECHANICAL SECTION DESCRIPTION REFERENCE NAME DESCRIPTION REFERENCE NAME ANT CC-CAP C-CAP TN C-COIL ANTENNAS CHIP CAP, CHIP CAP, CHIP TANTALUM COIL, CHIP ADHESHIVE AZ BAR-ANT BAT BATT SHEET ADHESHIVE AZIMUTH BAR-ANTENNA BATTERY BATTERY C-DI C-DIODE C-FET C-FOTR C-JACK DIODE, CHIP DIODE, CHIP FET, CHIP FILTER, CHIP JACK, CHIP BRG BTN CAB CASS CHAS BEARING BUTTON CABINET CASSETTE CHASSIS C-LED C-RES C-SFR C-SLIDE SW C-SW LED, CHIP RES, CHIP SFR, CHIP SLIDE
2–11, IKENOHATA 1–CHOME, TAITO-KU, TOKYO 110-8710, JAPAN TEL:03 (3827) 3111 737004 Printed in Singapore
