CT-X408 n STEI?EO CAR CASSETTE RECEIVER RADIO-CASSETTE ESTEREOFONICO PARA AUTOMOVIL OWNER’S RECORD For your convenience, record the model number and serial number (you will find them on the right side of yourset) inthespace provided below. Please referto them when you contact your AIWA dealer in case of difficulty. Model NO. ICT-X40B Serinl No.
Welcome Thank you for your purchasing thisAIWA product. To optimize the performance of this unit, please read through this manual carefully. In addition to this operating instructions manual, be sure to refer to the separate installation and connections manuals as well. PRECAUTIONS This unit is designed to be operated on a 12-volt DC negative-ground electrical system only, ● To prevent short-circuiting, disconnect the negative car battery terminal until the unit has been mounted and connected completely.
TABLE OF CONTENTS FRONT PANEL ................................................................................................................................... 3 DETACHING AND AITACHING THE FRONT PANEL ...................................................................... 4 SETTING THE BEEP TONE ............................................................................................................... 5 SETTING THE CLOCK .................................................................................
FRONTPANEL Display window @H-BASS button @ PWR (power on/off) button @ SEL (select) button @ +/(audio control) button @EJECT = button @ Caaaette compartment @DIRECTION 4+/button @BAND button @ CRP (CD changer ready position) button @& (release) button @TUNE Y/A buttons @MUTE button @CD IN jack (3.5-mm dia.) @Preset station buttons I-6 @A.
Attaching the front pansl DETACHING AND ATTACHING THE FRONT PANEL 1 / 2 You can detach the front panel from the unit and carry it with you when you leave your car unattended. When you carry the front panel out of your car, use the supplied earring case. Before detaching the front panel, remove the cassette to prevent possible damage to the unit. 1 Press PWR to turn the unit off. 2 While supporting the front panel with one hand, press ~ to release one aide of the panel.
SETTING THE BEEP TONE SETTING THE CLOCK 3 1 The unit is preset at the factory to beep each time you press any button on the front panel except OPEN. You can stop beeping by following the procedure below. 2;4 [@cl 1 -i EKIl 1 2 With the unit off, press 1 and 4 at the same time. The “BEEP indication appears. Each time you press them, this function turns on or off.
PWR RADIO OPERATION 1 TUNE VIA 32 LO 4 1 Press PWR to turn the unit on. The radio frequency appears. 2 Press BAND to select the band from among FM1, FM2, FM3 and AM. The band indication appears cyclically in order. (FM1, FM2 and FM3 share the same frequency range.) Band indication I LO (local/DX) button You can use Local mode when you wish to tune in only strong stations during seek tuning. In Radio mode, press LO to select Local mode. The “LO” indicator lights up.
PRESETTING STATIONS hT Press BAND to selects desired bend from among FMI, FM2, FM3 and AM. FM 1 I I r-l / /.../ /“”-/ /.../. / / I Press and hold A.ME for more than 1.5 seconds to activate the automatic preseting function. The six strongest available stations will be stored in memory on the preset station buttons 1 to 6 in order of their signal strength. Use this function to automatically preset up to 6 stations each for FM1, FM2, FM3 and AM (up to a total of 24 stations).
TAPE PLAYBACK 1 2 1 2 Press BAND to selects desired band from among FM1, FM2, FM3 and AM. I Irreert a caasette to start playback. Playbackstartsin the directionthatthe unit playedback previously. z Adjust the volume with +/-. Press thedeeired txeaet station button. The number of the-pressed preset station button is displayed next to the frequency indication.
TAPE PLAYBACK SOUNDADJUSTMENTS Auto reversefunction 12 When the end of the tape is reached during playbackor fast tape transport,the directionof thetapeis automaticallyreversed,andplayback startsagain. Tapadirectionindications MUTE 1 w 8 , Lower side + 24” ‘f \\’ Beforeturningthe ignitionoff pwlblh’ Be sure to eject any cassette from the unit before turning the ignition off. Otherwise, fhe unit maybe damaged when you detach the front panel.
MUTEbutton PressthisbuttontotemporarilyIowerthevolume. Pressit againto restorethe previousvolume. You can enjoy music with strong bass sound. CRP (CD changer ready oosition) You can enjoy CD changer play in combination with your RF-CD-changer system with easy operation. H-BASS 24 1 Press H-BASS to obtain powerful bass. The “H BASS” indicator lights up. Each time you press H-BASS, this function turns on or off. \ , / 3 1 Press PWR to turn the unit on. The radio frequency indication appears.
CRP (CD changer ready position) 14 CONNECTING A PORTABLE CD PLAYER OR OTHER EQUIPMENT 2 This unit is equipped with the line-level input (CD IN) jack enabling high quality of the sound. 31 (1 I 11 ~ 1 Press PWR to turn the unit on. If a cassette is inserted, remove it to prevent possible damage to the unit. z Press CRP to switch the unit to CRP mode. 2 4 The “CRP” indicator lights up. s PlayaCDwith yourCDchangersyatem. A Adjuet the volume with +/-.
MAINTENANCE SPECIFICATIONS Cleaningthe frontpanel When the frontpanelis soiled,wipethe surface of the panelwitha dryand softcloth. RADIO SECTfON Cleaningthe tapehead Use a cleaningcassetteto clean the playback headandcapstansapproximatelyoncea month. If the playbackhead is dirty,the hightonesmay notbe reproducedproperly. Cleaningthe connector The connector on the reverse side of the front panel needs to be cleaned occasionally.
88-KTD-903-01 9801 O9BTM-O)( AIWA CO.,LTD.