Service manual

ManualsBrandsAiwa ManualsMiniDisc PlayerJAX-S5

SERVICE MANUAL

TUNER

FM tuning range 87.5 MHz to 108 MHz

AEP, UK models:

Except AEP, UK models:

usable sensitivity (IHF)

16.8 dBf

FM antenna terminal 75 ohms (unbalanced)

AEP, UK, E, EA, TW models:

E51 model:

tuning range

531 kHz to 1602 kHz

AM usable sensitivity 350 µV/m

SP, AUS models:

530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1602 kHz (9 kHz step)

AM antenna Loop antenna

AMPLIFIER

Power

AEP, UK models:

Except AEP, UK models:

output

Rated: 12 W + 12 W (6 ohms, T.H.D.

1 %, 1 kHz/DIN 45500)

Reference: 15 W + 15 W (6 ohms,

T.H.D. 10 %, 1 kHz/DIN 45324)

MUSIC POWER: 27 W +27 W

CASSETTE DECK

Track format 4 tracks, 2 channels stereo

Frequency response 50 Hz – 8 kHz

Recording system AC bias

Heads Deck A: playback x 1

Deck B: recording/playback x 1,

erase x 1

CD PLAYER

Laser Semiconductor laser

(λ = 780 nm)

Emission duration:

continuous

D/A converter 1 bit dual

Signal-to-noise ratio 85 dB (1 kHz, 0 dB)

Harmonic distortion 0.05 % (1 kHz, 0 dB)

AEP, UK models:

Except AEP, UK models:

Power consumption

40 W

Power consumption With ECO mode on: 0.25 W

in standby mode With ECO mode off: 15 W

Dimensions (W x H x D) 280 x 330 x 392.5 mm

Weight

6.1 kg

Specifications and external appearance are subject to change

without notice.

13.2 dBf

530 kHz to 1710 kHz (10 kHz step)

531 kHz to 1710 kHz (9 kHz step)

Rated: 36 W + 36 W (1 kHz, T.H.D. 1

%, 6 ohms)

Reference: 45 W + 45 W (1 kHz,

T.H.D. 10 %, 6 ohms)

74 W

E, EA, SP, TW, AUS models: 6.8 kg

E51 model:

6.7 kg

Total harmonic distortion 0.08 % (6 W, 1 kHz, 6 ohms, DIN

AUDIO)

(Except AEP, UK models)

Input VIDEO/AUX: 400 mV

Outputs SPEAKER:

MIC: 1.7 mV (10k ohms)

6 ohms or more

PHONES: 32 ohms or more

Check copyright laws relevant to recordings from discs, tuner

or tape for the country where the unit is to be used.

GENERAL

Power

AEP, UK models:

E, E51, SP models:

TW model:

requirements

230 V AC, 50/60 Hz

110

120 V AC, 50 Hz/60 Hz

- 120V / 220 - 240V AC

(Switchable), 50 Hz/60 Hz

EA model:

120 - 127V / 220 V AC

(Switchable), 50 Hz/60 Hz

AUS model:

240 V AC, 50 Hz/60 Hz

COMPACT DISC DECK RECEIVER

AEP Model

UK Model

E Model

Australian Model

CX-JN10

Ver 1.0 2004.03

9-877-593-01 Sony Corporation

2004C05-1 Home Audio Company

SPECIFICATIONS

CX-JN10 is the tuner, amplifier, cassette deck

and CD player section in JAX-N10/PK10.

Model Name Using Similar Mechanism CX-JN1

CD Mechanism Type CDM74S-K6BD72

Base Unit Name BU-K6BD72

Section

Optical Pick-up Block Name KSM-213DCP

Optical Pick-up Name KSS-213D

Tape deck

Model Name Using Similar Mechanism CX-JN1

Section

Tape Transport Mechanism type CWM43FF13

• Abbreviation

AUS : Australian model

E51 : Chilean and Peruvian models

EA : Saudi Arabia model

SP : Singapore model

TW : Taiwan model

Summary of content (72 pages)

PAGE 1
CX-JN10 SERVICE MANUAL AEP Model UK Model E Model Australian Model Ver 1.0 2004.03 CX-JN10 is the tuner, amplifier, cassette deck and CD player section in JAX-N10/PK10.
PAGE 2
CX-JN10 Notes on chip component replacement • Never reuse a disconnected chip component. • Notice that the minus side of a tantalum capacitor may be damaged by heat. Flexible Circuit Board Repairing • Keep the temperature of the soldering iron around 270 °C during repairing. • Do not touch the soldering iron on the same conductor of the circuit board (within 3 times). • Be careful not to apply force on the conductor when soldering or unsoldering.
PAGE 3
CX-JN10 TABLE OF CONTENTS 1. 2. SERVICING NOTES ................................................ 4 GENERAL Location of Controls ....................................................... 7 3. DISASSEMBLY 3-1. 3-2. 3-3. 3-4. 3-5. 3-6. 3-7. 3-8. 3-9. 3-10. 3-11. 3-12. 3-13. 3-14. Disassembly Flow ........................................................... Case (SIDE-L/R) ............................................................. Case (Top) ................................................................
PAGE 4
CX-JN10 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK OR BASE UNIT • MODEL IDENTIFICATION – Back Panel – The laser diode in the optical pick-up block may suffer electrostatic break-down because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body. During repair, pay attention to electrostatic break-down and also use the procedure in the printed matter which is included in the repair parts.
PAGE 5
CX-JN10 HOW TO OPEN THE DISC TRAY WHEN POWER SWITCH TURNS OFF. 1 Remove the case (side-L). 2 Turn the loading gear in the direction of arrow A. A 3 Pull-out the disc tray.
PAGE 6
CX-JN10 SERVICE POSITION – CD mechanism deck – main board (CN691) Connect wire (flat type) (19 core) to main board (CN691) and BD board (CN710). BD board (CN710) – Tape mechanism deck – panel board (CN601) main board (CN302) Connect wire (flat type) (13 core) to panel board (CN601) and mechanical deck.
PAGE 7
CX-JN10 SECTION 2 GENERAL This section is extracted from instruction manual. • LOCATION OF CONTROLS Main unit: front Refer to the pages indicated in parentheses for details. 5 MULTI JOG When used in combination with ENTER and MULTI JOG, CD: selects a track and Repeat/Shuffle/Programmed playback. Tuner: selects a preset station. Tape: specifies tape length. Clock and Timer: sets the time. ECO and Dimmer: selects the mode. 6 PHONES jack Plug in here an optional headphones set with a mini stereo plug (ø3.
PAGE 8
CX-JN10 Remote control TAPE A/B Refer to the pages indicated in parentheses for details. TUNER MODE Switches between stereo or monaural FM reception. 3 r, t CD: selects a track. Tuner: selects a preset station. Tape: specifies tape length. BASS and TREBLE: adjusts the level. Clock and Timer: sets the time. 4 PLAY MODE Selects Shuffle or Programmed playback in CD function. REPEAT Enters CD repeat playback mode.
PAGE 9
CX-JN10 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed. SET 3-2. CASE (SIDE-L/R) (Page 10) 3-3. CASE (TOP) (Page 10) 3-4. TRAY PANEL (Page 11) 3-5. CD MECHANISM DECK (CDM74S-K6BD72) (Page 11) 3-6. FRONT PANEL SECTION (Page 12) 3-8. REAR CABINET SECTION (Page 13) 3-10.
PAGE 10
CX-JN10 Note: Follow the disassembly procedure in the numerical order given. 3-2. CASE (SIDE-L/R) 2 two screws (BVTP3 × 10) 5 case (side-L) 1 two case screws 2 two screws (BVTP3 × 10) 3 4 1 case screw 1 two case screws 3 4 5 case (side-R) 1 case screw 3-3.
PAGE 11
CX-JN10 3-4. TRAY PANEL 1 Turn the loading gear in the direction of arrow A. A 2 Pull-out the disc table. 3 four claws 4 tray panel 3-5.
PAGE 12
CX-JN10 3-6. FRONT PANEL SECTION 1 screw (BVTP3 × 10) 3 screw (BVWHTP) 2 terminal 4 HP board 8 connector (CN101) 5 wire (flat type) (11 core) (CN694) 6 connector (CN302) 6 connector (CN301) 9 front panel section 7 three screws (BVTP3 × 10) 3-7.
PAGE 13
CX-JN10 3-8. REAR CABINET SECTION 3 rear cabinet section 1 wire (flat type) (11 core: EXCEPT AEP, UK) (CN801) (15 core: AEP, UK) (CN802) 2 three screws (BVTP3 × 10) 2 screw (BVTP3 × 10) 3-9.
PAGE 14
CX-JN10 3-10. TABLE ASSY 5 two claws A 4 hook 3 wire (flat type) (5 core) (CN702) 1 Turn the loading gear in the direction of arrow A. 2 Pull-out the table assy. 6 table assy 3-11. MOTOR (TB) BOARD 1 screw (PTPWH M2.6) 2 table (loading) 3 belt (table) 6 MOTOR (TB) board 4 connector (CN731) 5 two screws (BTTP M2.
PAGE 15
CX-JN10 3-12. MOTOR (LD) BOARD 3 two screws (BTTP M2.6) 4 MOTOR (LD) board 2 connector (CN704) 1 belt (loading) 3-13. BASE UNIT (BU-K6BD72) 6 9 base unit (BU-K6BD72) 7 three insulators 3 three coil springs (insulator) 2 three stoppers (BU) 1 three screws (BTTP M2.6) 8 insulator 5 coil spring (insulator) 4 screw (PTPWH M2.
PAGE 16
CX-JN10 3-14. MOTOR GEAR ASSY (SLED) (M701), BD BOARD 7 gear (A) 6 claw 8 gear (B) 2 two screws (P2 × 3) 5 wire (flat type) (16 core) (CN708) qa BD board 0 motor gear assy (SLED) (M701) 1 Remove two solders. 4 3 screw (BTP2.6 × 8) 9 Remove two solders.
PAGE 17
CX-JN10 SECTION 4 TEST MODE MC COLD RESET • The cold reset clears all data including preset data stored in the RAM to initial conditions. Execute this mode when returning the set to the customer. Procedure: 1. In the standby status, while pressing the x button, press the [POWER] button. 2. The set is reset, then becomes standby status. GC TEST MODE Procedure: 1. Press the [POWER] button to turn the power on. 2. While pressing the x button, press the [POWER] button for 5 seconds. 3.
PAGE 18
CX-JN10 CD TEST MODE • This mode can run the CD sled motor freely. Use this mode, for instance, when cleaning the pickup. Procedure: 1. In the status where AC plug is disconnected, while pressing the [CD] button, connect the AC plug to turn the power on. 2. When enter this mode, it displays “CD TEST” and few seconds later, all segments turn on of the fluorescent indicator tube. 3. To release from this mode, disconnect the AC plug and turn the power off. In this mode, it operates as following table.
PAGE 19
CX-JN10 SECTION 5 ELECTRICAL ADJUSTMENTS Note: Clear RF signal waveform means that the shape “ ◊ ” can be clearly distinguished at the center of the waveform. CD SECTION Note: 1. CD Block is basically designed to operate without adjustment. Therefore, check each item in order given. 2. Use YEDS-18 (3-702-101-01) unless otherwise indicated. 3. Use an oscilloscope with more than 10MΩ impedance. 4.
PAGE 20
CX-JN10 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – CD Section – OPTICAL PICK-UP BLOCK (KSM-213DCP) CD DSP IC721 A 8 FIN2 LCHO DETECTOR A D I-V AMP D C B 7 RF EQ, AGC RF AMP 4 3 EFMIN ERROR CORRECT D/A CONVERTER B 9 EXTERNAL AUDIO IN ASDFIN 57 ASDACK 56 ASLRCK 55 SERIAL OUT DATA 60 DATACK 59 LRSY 58 TIN1 10 TIN2 LASER DIODE SERVO PROCESSOR AUTOMATIC POWER CONTROL Q701 LD 80 16MOUT XIN APC D/A CONVERTER PD 79 S701 (LIMIT IN) CLOCK GENERATOR XOUT X701 16.
PAGE 21
CX-JN10 6-2.
PAGE 22
CX-JN10 BLOCK DIAGRAM – AMP/POWER SUPPLY Section – (EXCEPT AEP, UK) MIC LEVEL AGC Q401 (EXCEPT AEP, UK) VR401 MIC MIXING J401 MIC MIC AMP IC401 (1/2) (Page 21) H MIC AMP IC401 (2/2) F –VH OUTPUT LEVEL DETECT Q235 R-CH +VL L CURRENT MIRROR Q105, 107 R-CH CD –VL (AEP, UK) PB, REC +VP 21 B-IN PB-OUT 6 TU + 7 VOL-IN PRE DRIVE Q101, 103 OUT 18 23 C-IN PB 2 PB1P REC CASCADE Q109 (AEP, UK) Q109, 111 (EXCEPT AEP, UK) MUTING Q181 CONT (Page 21) 28 REC1O INPUT SELECT, ELECTRICAL VOLUM
PAGE 23
CX-JN10 6-4. • Circuit Boards Location NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: • X : parts extracted from the component side. • Y : parts extracted from the conductor side. • x : parts mounted on the conductor side. : Pattern from the side which enables seeing. • (The other layers' patterns are not indicated.) • Indication of transistor. C Q These are omitted. B E Q B C E These are omitted.
PAGE 24
CX-JN10 6-5. PRINTED WIRING BOARD – BD Section – • See page 23 for Circuit Boards Location. :Uses unleaded solder.
PAGE 25
CX-JN10 R729 12k C744 1 C754 47p R726 680 R725 680 AUTOMATIC POWER C703 0.1 E R711 330 R702 15k D R703 15k B R704 15k C R705 15k F R701 47k GND R706 47k CL CE CL DI DO DATA EFMIN LRSY R751 47k TP (RF) RF ASDFIN R752 47k 16MOUT FIN2 EFLG TIN1 C2F TIN2 XVSS VREF CD DSP REF1 IC721 LC78646E-E C716 0.001 F+ C717 T- C718 1 T+ C719 R754 47k FSX/16MIN R765 1M R713 1k FE XOUT TEC XVDD TE RVDD RFMON RCHO JITTC RVSS ADAVDD LVSS FB701 0.0047 X701 16.
PAGE 26
CX-JN10 PRINTED WIRING BOARDS – CHANGER Section – • See page 23 for Circuit Boards Location. SENSOR BOARD A :Uses unleaded solder.
PAGE 27
CX-JN10 FIN GND RIN FIN GND RIN VM VCC VM VCC RNF OUT1 OUT1 DRIVE OUT2 VREF LOADING MOTOR RNF SCHEMATIC DIAGRAM – CHANGER Section – • See page 42 for IC Block Diagrams. IC701 BA6956AN CN721 2P M751 R702 100 CN704 2P LM-2 LM-2 LM-1 LM-1 C751 0.01 (LOADING) R701 470 D701 MTZJ-T-77 5.1A S711 TABLE MOTOR CN703 4P E3 E-3 E2 E-2 E1 E-1 VREF ADDRESS DETECT DRIVE OUT2 DISC TRAY IC712 BA6956AN R721 4.7k R723 4.7k R722 4.7k C737 0.1 C735 0.1 GND C736 0.1 6-8.
PAGE 28
CX-JN10 6-9. SCHEMATIC DIAGRAM – MAIN Section (1/4) – (1/4) R017 (EXCEPT AEP,UK) VM(AC) (AUS) 0.22 (AEP,UK) 0.33 (EXCEPT AEP,UK) D019 EGP20D VM(AC) C007 VH(AC) D021 EGP20D D020 EGP20D D022 EGP20D 3300 25V (AEP,UK) 3300 35V (EXCEPT AEP,UK) A1 VH(AC) C011 C012 C033 0.1 0.1 0.
PAGE 29
CX-JN10 6-10. SCHEMATIC DIAGRAM – MAIN Section (2/4) – R123 6.8k D107 MC2838 R131 4.7k Q101,103 PRE DRIVE (AEP,UK) (2/4) R119 2.2k Q103 2SA1235 OUT-L C113 33 50V 5.6k (EXCEPT AEP,UK) Q101 2SA1235 C111 100p ∗ D109 AU-01Z C115 820p ∗ R115,116 VDD F2 HOLD Q107 2SC3052 27k (EXCEPT AEP,UK) O-MUTE C131 100p Q181 2SD1306 NE R182 12k Q183 2SA1235 CD-D-GND MUTING FR-A-GND 1.8k (EXCEPT AEP,UK) R141 ∗ Q182 2SD1306 NE R122 1k Q110 2SD814A CASCADE Q102 2SA1235 C116 R126 820p 1.
PAGE 30
CX-JN10 • See page 42 for IC Block Diagram. 6-11. SCHEMATIC DIAGRAM – MAIN Section (3/4) – • See page 42 for Waveforms. (3/4) SP-A-GND C687 0.01 TU/AUX-A-GND B3 CD-A-GND B4 FR-A-GND FUNC-A-GND CD-D-GND B5 CD-P-GND B6 FR-D-GND CD-VM B7 CD-VM 4V 4V VSS TP601 VSS VDD R VDD G L (AEP,UK) F1 F1 JR601 0 F2 (Page 29) F2 R653 22k JR611 0 HOLD HOLD ~~~~ ~~~ VM B8 VM R654 22k -VFL -VFL (AEP,UK) O-POWER O-POWER O-MUTE O-MUTE R655 22k R645 4.7k R656 22k R612 4.7k C734 0.1 C733 0.
PAGE 31
CX-JN10 6-12. SCHEMATIC DIAGRAM – MAIN Section (4/4) – • See page 42 for IC Block Diagram. (EXCEPT AEP,UK) (4/4) RDS-CLK CN801 11P RDS-DATA B3 B4 CLK (AEP,UK) CL IFC C912 100p C911 100p DO DATA FM 75Ω DI (COAXIAL) PLL-CE B5 TUNER PACK CE VM B6 SUPPLIED WITH +9V THE ASSEMBLED TUNED B7 TUNED BLOCK STEREO B8 STEREO TU-L L-CH AM LOOP GND TU-R R-CH TU-MUTE MUTE R801 220 CN802 15P DO CE (AEP,UK) +9V C913 1000p (AEP,UK) C801 10 50V DI C802 0.1 D801 UDZS-175.
PAGE 32
CX-JN10 6-13. PRINTED WIRING BOARD – MAIN Section – • See page 23 for Circuit Boards Location. 1 2 3 4 5 :Uses unleaded solder.
PAGE 33
CX-JN10 6-14. PRINTED WIRING BOARD – HP Section – • See page 23 for Circuit Boards Location. 6-15. SCHEMATIC DIAGRAM – HP Section – :Uses unleaded solder. E MAIN BOARD WH201 (Page 32) FB221 5 WH230 5P WH230 JW222 J221 GND JW224 JW222 R-IN L-IN R224 JW216 R225 R223 R226 ∗ ∗ ∗ R225,226 150 (EXCEPT AEP,UK) JW225 JW223 180 (AEP,UK) JW221 FB221 R221 (CHASSIS) 15 C250 (15) 1-688-400- J221 PHONES • Semiconductor Location – MAIN Board – Ref. No. Location Ref. No.
PAGE 34
CX-JN10 6-16. PRINTED WIRING BOARD – PANEL Section – • See page 23 for Circuit Boards Location.
PAGE 35
CX-JN10 • See page 42 for IC Block Diagrams. 6-17. SCHEMATIC DIAGRAM – PANEL Section – • See page 42 for Waveforms. • See page 45 for IC Pin Function Description.
PAGE 36
CX-JN10 6-18. PRINTED WIRING BOARDS – KEY Section – • See page 23 for Circuit Boards Location. :Uses unleaded solder.
PAGE 37
CX-JN10 R801 10k R803 10 K5 K6 K8 K7 6-19. SCHEMATIC DIAGRAM – KEY Section – R809 10k A 1 R811 10 A S801 2 B B 3 B8 S301 S302 R305 1.2k S303 R306 1.2k S304 R810 C805 10k 1000p R805 10k R807 10 R813 10k A 1 STOP/ PAUSE/ TUNING DOWN CLEAR PRESET R812 10 S306 S305 i-BASS PLAY/ C806 1000p K1 R304 1k 3 R804 10 K2 R303 820 K4 R302 1k C802 1000p K3 R301 0 C801 1000p A 2 B B10 R311 0 R312 1k R313 820 R314 1k R315 1.2k R316 1.
PAGE 38
CX-JN10 6-20. PRINTED WIRING BOARD – PT Section – (AEP, UK, AUS) • See page 23 for Circuit Boards Location. :Uses unleaded solder.
PAGE 39
CX-JN10 6-21. SCHEMATIC DIAGRAM – PT Section – (AEP, UK, AUS) (AEP,UK) WH091 7P VL(AC) VL(AC) GND(M) FIL-1 FIL-2 (Page 28) P-ON VSTBY PT002 POWER TRANSFORMER WH093 11P (MAIN) VM(AC) VM(AC) ∗ NOT REPLACEABLE: VH(AC) BUILT IN TRANSFORMER VH(AC) VL(AC) ∗ VL(AC) GND(M) FIL-1 (Page 28) FIL-2 (AEP,UK) P-ON C091 0.
PAGE 40
CX-JN10 6-22. PRINTED WIRING BOARD – PT Section – (E, EA, E51, SP, TW) • See page 23 for Circuit Boards Location. :Uses unleaded solder.
PAGE 41
CX-JN10 6-23. SCHEMATIC DIAGRAM – PT Section – (E, EA, E51, SP, TW) PT004 POWER TRANSFORMER CN093 11P (MAIN) VM(AC) VM(AC) VH(AC) VH(AC) (E,EA,E51,SP) VL(AC) -1 VL(AC) JW032 S001 GND(M) VOLTAGE (TW) SELECTOR FIL-1 100-120V ∗ (Page 28) FIL-2 -2 220-240V P-ON VSTBY C003 0.
PAGE 42
CX-JN10 • Waveforms – BD Board – – MAIN Board – – PANEL Board – • IC Block Diagrams – BD Board – 1 IC721 4 (RF) (CD Play Mode) qa L311 6, 7 (REC Mode) qf IC901 qd (XT2) IC721 TIN1 qg IC901 qh (CF2) TIN2 50 Vp-p VSS VDD5 DRF RES WRQ DO DI CL CE RF TEC TE DRF WRQ DO DI CL CE FR VVDD PCKIST VVSS PDO2 PDO1 CONT1 CONT2 CONT3 PH AGC EQ BH LPF + – TBAL + – TBAL LPF SW + – LPF + – + – RFMON LEVEL SET REFI Approx. 180 mVp-p MIX + – 30.
PAGE 43
CX-JN10 – DRIVER Board – IC701, 712 BA6956AN TSD 7 8 9 GND RIN 6 FIN 5 VCC 4 VM OUT2 3 OUT1 2 RNF 1 VREF CONTROL LOGIC – MAIN Board – REC1N REC2N REC2O INC2 INC1 INB2 INB1 INA2 INA1 OUT1 BAS1 OUT2 BAS2 BD3881FV REC1O IC601 28 27 26 25 24 23 22 21 20 19 18 17 16 15 BASS VOLUME TREBLE LOGIC CONTROL 5 6 7 8 9 10 11 12 13 14 PB1O VOLIN1 VOLIN2 GND TRE1 TRE2 VDD CONT VEE TREBLE PB2O 4 PB2N PB1P Q11 Q10 Q9 Q8 Q7 Q6 Q5 OE BU2092F-E2
PAGE 44
CX-JN10 – PANEL Board – Q11 Q10 Q9 Q8 Q7 Q6 Q5 Q11 OE BU2099FV VDD IC201 20 19 18 17 16 15 14 13 12 11 12 BIT SHIFT REGISTER CONTROL CIRCUIT 5 6 7 8 9 10 Q0 Q1 Q2 Q3 Q4 VOUT MM1614A VIN IC501 4 LCK VSS N.C.
PAGE 45
CX-JN10 • IC Pin Function Description PANEL BOARD IC901 LC87696B-52D8 (SYSTEM CONTROLLER) LC876772B-52N2-E (AEP and UK models), LC876756C-52N7-E (EXCEPT AEP and UK models) Pin No.
PAGE 46
CX-JN10 Pin No.
PAGE 47
CX-JN10 SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they are seldom required for routine service. Some may have some difference from the original delay should be anticipated when ordering one. these items. • Color Indication of Appearance Parts • The mechanical parts with no reference numExample: ber in the exploded views are not supplied. KNOB, BALANCE (WHITE) . . .
PAGE 48
CX-JN10 7-2. TAPE DECK SECTION #1 not supplied 51 #1 (EXCEPT AEP, UK) 56 52 not supplied 53 55 54 panel board section Ref. No. 51 52 53 54 48 Part No. Description 4-245-177-11 4-245-179-11 4-245-182-11 4-245-176-11 ROTARY (JOG), KNOB ROTARY (TRE), KNOB PLATING, KNOB ROTARY (VOL) PLATING, KNOB ROTARY (BASS) Remark Ref. No. 55 56 #1 Part No.
PAGE 49
CX-JN10 7-3. PANEL BOARD SECTION #1 #1 105 101 not supplied 103 102 106 107 108 #1 (EXCEPT AEP, UK) #1 104 #1 109 (EXCEPT AEP, UK) not supplied 110 111 key section Ref. No. 101 102 103 Part No.
PAGE 50
CX-JN10 7-4. KEY SECTION 156 154 155 152 157 front cabinet section 151 153 Ref. No. Part No. Description 151 152 152 152 153 4-245-193-01 4-254-978-01 4-254-978-11 4-254-978-51 4-233-980-01 RING (BASS) WINDOW, DISPLAY (AEP, UK) WINDOW, DISPLAY (E, EA, SP, TW, AUS) WINDOW, DISPLAY (E51) RUBBER FOOT 154 4-245-171-11 KEY (CD) (DISC CHANGE. 1. 2. 3. Z) 50 Remark Ref. No. 155 156 157 157 Part No. Description Remark 4-245-172-21 KEY (FUN) (TAPE A/B. TUNER BAND. VIDEO/AUX. CD. N.
PAGE 51
CX-JN10 7-5. FRONT CABINET SECTION 207 211 208 210 205 212 209 206 210 204 203 201 Ref. No. 202 Part No. Description 201 202 203 204 205 4-245-198-01 4-245-160-21 4-245-196-01 4-245-197-01 4-245-159-11 WINDOW (2), CASSETTE BOX (2), CASSETTE SPRING (BOX CASS R), TORSION WINDOW (1), CASSETTE BOX (1), CASSETTE 206 207 4-245-195-01 SPRING (BOX CASS L), TORSION 4-254-979-01 CABINET, FRONT (AEP, UK) Remark Ref. No. Part No.
PAGE 52
CX-JN10 7-6. CHASSIS SECTION (E, EA, E51, SP, TW) 258 252 252 not supplied not supplied #2 #1 251 A PT004 259 #1 254 #1 (AEP, UK, AUS) 252 #1 #1 252 not supplied not supplied #2 251 #1 not supplied not supplied 258 258 not supplied not supplied 256 PT002 A 255 257 253 258 260 not supplied B 258 A (AEP, UK) C911 C912 C913 not supplied C950 258 B #1 not supplied The components identified by mark 0 or dotted line with mark 0 are critical for safety.
PAGE 53
CX-JN10 7-7. CD MECHANISM DECK SECTION-1 (CDM74S-K6BD72) 502 502 505 503 504 502 507 506 501 515 508 514 516 513 M741 515 509 516 514 513 510 512 511 503 CD mechanism deck section -2 Ref. No. Part No. Description 501 502 503 504 505 4-243-815-01 4-218-252-61 4-218-253-21 1-687-132-12 4-243-819-01 TABLE (LOADING) SCREW (+PTPWH M2.6), FLOATING SCREW (M2.
PAGE 54
CX-JN10 7-8. CD MECHANISM DECK SECTION-2 (CDM74S-K6BD72) 559 562 551 560 551 558 564 554 561 565 S711 563 M751 CD mechanism deck section -3 556 557 553 555 552 554 551 Ref. No. Part No. Description 551 552 553 554 555 4-218-252-61 4-244-034-01 4-224-613-01 4-218-253-31 1-687-669-12 SCREW (+PTPWH M2.6), FLOATING BELT (LOADING) GEAR (SHAFT) SCREW (M2.
PAGE 55
CX-JN10 7-9. CD MECHANISM DECK SECTION-3 (CDM74S-K6BD72) 603 604 605 602 601 612 606 604 BU-K6BD72 607 607 608 609 608 610 Ref. No. Part No. Description 601 602 603 604 605 X-4955-707-2 1-471-035-11 4-231-189-01 4-218-252-61 4-243-822-02 PULLEY (A5) ASSY, CHUCKING MAGNET ASSY PULLEY (B), CHUCKING SCREW (+PTPWH M2.6), FLOATING LEVER (LIFTER) 606 X-4955-536-1 HOLDER (213) ASSY Remark 611 Ref. No. Part No.
PAGE 56
CX-JN10 7-10. BASE UNIT SECTION (BU-K6BD72) 652 not supplied (M702) not supplied (M701) 653 #3 651 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified. Ref. No. Part No. 651 0 652 A-4734-406-A BD BOARD, COMPLETE A-4735-357-A BASE ASSY, OP (KSM-213DCP) (including M701 (SLED), M702 (SPINDLE)) 56 Description Remark Ref. No. 653 #3 Part No. Description 1-792-024-11 WIRE (FLAT TYPE) (16 CORE) 7-685-534-19 SCREW +BTP 2.
PAGE 57
CX-JN10 SECTION 8 ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the parts list may be different from the parts specified in the diagrams or the components used on the set. • -XX and -X mean standardized parts, so they may have some difference from the original one. • RESISTORS All resistors are in ohms. METAL: Metal-film resistor. METAL OXIDE: Metal oxide-film resistor. F: nonflammable • Abbreviation AUS : Australian model E51 : Chilean and Peruvian models Ref. No. Part No.
PAGE 58
CX-JN10 BD Ref. No. CD KEY DRIVER HP Part No. Description R726 R727 R728 R729 1-216-819-11 1-216-809-11 1-216-841-11 1-216-834-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP 680 100 47K 12K 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W Remark R730 R731 R732 R738 R739 1-216-822-11 1-216-825-11 1-216-864-11 1-218-867-11 1-216-864-11 METAL CHIP METAL CHIP SHORT CHIP METAL CHIP SHORT CHIP 1.2K 2.2K 0 6.8K 0 5% 5% 1/10W 1/10W 0.
PAGE 59
CX-JN10 HP Ref. No. Part No. Description Remark R226 1-260-089-11 CARBON 150 R226 1-260-090-61 CARBON 180 5% 1/2W (EXCEPT AEP, UK) 5% 1/2W (AEP, UK) Ref. No. Part No. KEY Description Remark < FERRITE BEAD > FB401 1-410-396-41 FERRITE 0.
PAGE 60
CX-JN10 KEY Ref. No. MAIN Part No. Description Remark R408 1-216-174-00 RES-CHIP 100 R409 1-216-825-11 METAL CHIP 2.2K R410 1-216-825-11 METAL CHIP 2.2K R411 1-216-825-11 METAL CHIP 2.2K R412 1-216-825-11 METAL CHIP 2.
PAGE 61
CX-JN10 MAIN Ref. No. Part No.
PAGE 62
CX-JN10 MAIN Ref. No. Part No. Description C605 C606 C607 C608 C609 1-130-481-00 1-130-481-00 1-162-962-11 1-162-962-11 1-126-960-11 MYLAR MYLAR CERAMIC CHIP CERAMIC CHIP ELECT 0.0068uF 0.0068uF 470PF 470PF 1uF 5% 5% 10% 10% 20% 50V 50V 50V 50V 50V Remark C610 C611 C612 C613 C614 1-126-960-11 1-164-739-11 1-164-739-11 1-162-967-11 1-162-967-11 ELECT CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP CERAMIC CHIP 1uF 560PF 560PF 0.0033uF 0.
PAGE 63
CX-JN10 MAIN Ref. No. Remark Ref. No. Part No. Description D662 D663 D671 D691 D692 8-719-083-60 8-719-988-61 8-719-988-61 6-500-522-21 6-500-522-21 DIODE DIODE DIODE DIODE DIODE UDZSTE-174.7B 1SS355TE-17 1SS355TE-17 10EDB40-TB3 10EDB40-TB3 JR651 JR701 JR801 D693 D694 D695 D697 D801 6-500-522-21 6-500-522-21 8-719-988-61 6-500-522-21 8-719-069-54 DIODE DIODE DIODE DIODE DIODE 10EDB40-TB3 10EDB40-TB3 1SS355TE-17 10EDB40-TB3 UDZSTE-175.
PAGE 64
CX-JN10 MAIN Ref. No. Part No.
PAGE 65
CX-JN10 MAIN Ref. No. Part No. Description Remark R074 1-216-838-11 METAL CHIP 27K R075 1-216-830-11 METAL CHIP 5.
PAGE 66
CX-JN10 MAIN Ref. No. Part No. Description Remark R156 1-216-823-11 METAL CHIP 1.5K R157 R158 1-216-809-11 METAL CHIP 1-216-809-11 METAL CHIP 100 100 R159 R160 R161 1-216-049-11 RES-CHIP 1-216-049-11 RES-CHIP 1-218-867-11 METAL CHIP 1K 1K 6.8K R162 1-218-867-11 METAL CHIP 6.8K R163 1-216-830-11 METAL CHIP 5.6K R164 1-216-830-11 METAL CHIP 5.6K R181 R182 R183 1-216-834-11 METAL CHIP 1-216-834-11 METAL CHIP 1-216-830-11 METAL CHIP 12K 12K 5.6K R183 1-218-867-11 METAL CHIP 6.
PAGE 67
CX-JN10 MAIN Ref. No. Part No. Description Remark R610 R612 R615 R616 R617 1-216-836-11 1-216-829-11 1-216-835-11 1-216-835-11 1-216-835-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 18K 4.7K 15K 15K 15K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R618 R619 R620 R621 R622 1-216-835-11 1-216-838-11 1-216-838-11 1-216-830-11 1-216-830-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 15K 27K 27K 5.6K 5.
PAGE 68
CX-JN10 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C413 1-126-960-11 ELECT 1uF 20% 50V (EXCEPT AEP, UK) D508 D509 8-719-991-33 DIODE 1SS133T-77 8-719-991-33 DIODE 1SS133T-77 C414 1-164-156-11 CERAMIC CHIP 0.1uF C415 1-164-156-11 CERAMIC CHIP 0.1uF C501 C502 C503 1-126-960-11 ELECT 1-162-970-11 CERAMIC CHIP 1-126-960-11 ELECT 1uF 0.
PAGE 69
CX-JN10 PANEL Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R419 1-216-821-11 METAL CHIP 1K R501 R502 1-249-408-11 CARBON 1-216-841-11 METAL CHIP 180 47K 5% 1/10W (EXCEPT AEP, UK) 5% 1/4W 5% 1/10W R503 R504 R505 R506 R507 1-216-841-11 1-249-429-11 1-216-829-11 1-216-815-11 1-216-833-11 METAL CHIP CARBON METAL CHIP METAL CHIP METAL CHIP 47K 10K 4.
PAGE 70
CX-JN10 PANEL Ref. No. PT Part No. SENSOR Description Remark Ref. No. Part No. Description Remark R917 1-216-845-11 METAL CHIP 100K 5% 1/10W R973 1-216-845-11 METAL CHIP 100K R918 R919 R920 R921 R922 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 1-216-845-11 METAL CHIP METAL CHIP METAL CHIP METAL CHIP METAL CHIP 100K 100K 100K 100K 100K 5% 5% 5% 5% 5% 1/10W 1/10W 1/10W 1/10W 1/10W R974 1-247-879-11 CARBON 100K R975 R976 1-247-879-11 CARBON 1-216-825-11 METAL CHIP 100K 2.
PAGE 71
CX-JN10 SENSOR Ref. No. Part No. Description Remark Ref. No. < IC > Part No.
PAGE 72
CX-JN10 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. 1.0 Date 2004.