CD Stereo System OPERATING INSTRUCTIONS MANUAL DE INSTRUCCIONES En (English) E (Español) NSX-D30 U C MODE D'EMPLOI F (Français) OWNER'S RECORD Record the model number and serial number of your set (found at the rear of your set) below. Refer to them when contacting your Aiwa dealer. Model No. _____________________________ Serial No.
WARNING To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. En IMPORTANT SAFETY INSTRUCTIONS Read the Operating Instructions carefully and completely before operating the unit. Be sure to keep the Operating Instructions for future reference. All warnings and cautions in the Operating Instructions and on the unit should be strictly followed, as well as the safety suggestions below.
Overloading - Do not overload wall outlets, extension cords, integral convenience receptacles as this can result in a risk of fire or electric shock. Outdoor Antenna Power lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits.
PREPARATIONS Connection Plug in the AC power cord to the AC power outlet after all other connections are made. 1 Connect the front speakers. Connect the right front speaker to the SPEAKERS R terminals and place it on the right side of the unit. Connect the left to the SPEAKERS L terminals and place it on the left side.The speaker cords with the white stripes go to the 0 terminals. En 2 Connect the supplied antennas. Strip off the insulation of the FM antenna with twisting the cord.
PARTS AND CONTROLS Main unit: rear Dynamic Integrated Neo Amplifier 1 AM LOOP, FM 75 Ω terminals Plug in the supplied AM and FM antennas here. 2 VIDEO/AUX jacks Accepts analog sound signals from external equipment. Connect using an optional connecting cable with RCA phono plugs (red plug to R jack, white plug to L jack). Refer also to the operating instructions of your equipment. To switch function to external input, press VIDEO/AUX.
Main unit: front TIMER Enters timer setting mode. 3 SYNC DUB Starts dubbing a whole tape. En wREC/REC MUTE Starts recording. 4 aPAUSE/SET CD and Tape: pauses playback. Radio: stores the received station to preset. sSTOP/CLEAR CD and Tape: stops playback. Radio: clears a station preset. 1 TAPE/DECK 1/2 Selects Tape function, and deck 1 or 2. TUNER/BAND Selects Radio function and the radio band. VIDEO/AUX Selects the function of external equipment connected to VIDEO/AUX jacks. CD Selects CD function.
Remote control 3 The numbered buttons take on these functions when pressed together with SHIFT held down: RANDOM/REPEAT Enters random or repeat CD playback mode. 5 SHIFT Hold down when pressing a numbered button to change its function to that printed above the number. e.g.) "Press SHIFT+SLEEP on the remote control" indicates "Hold down SHIFT and press '6' (SLEEP)", so that you can use 'Sleep timer' function. TUNER MODE Switches between stereo or monaural FM reception.
ADJUSTMENTS BEFORE OPERATIONS DEMO If the clock has not been set, a DEMO appears on the display when the unit is turned off. To deactivate and activate the DEMO Press DEMO/ECO when the unit is turned off. En Spectrum analyzer display You can change the spectrum analyzer display. Press DISPLAY (SHIFT+DISPLAY on the remote control) repeatedly to select one of the three spectrum analyzer displays. Power Volume Turning the unit on Press POWER 6 STANDBY/ON (POWER on the remote control).
ECO mode Dimmer Setting the clock Reduces power consumption with the following operations, etc. Adjusts the brightness of the display. 1 Press SHIFT+CLOCK on the remote control. 1 Press DEMO/ECO twice when the unit is turned on, and then within 4 seconds press ENTER. 2 Press f or g to set the time. - The unit blacks out when the unit is turned off. Only the red indicator lights up. (Only when the clock is set.
CD OPERATIONS To replace disc(s) during playback without interruption While one disc is being played back, press DISC CHANGE so that the compartment opens, replace disc(s) with other one(s), and press DISC CHANGE to close the compartment. Random/Repeat playback En Random playback plays all the tracks on one desired disc or all the discs in random order. Repeat playback plays all the tracks repeatedly on one desired disc or all the discs.
Programed playback Plays back up to 30 selected tracks in programed order. 1 Press SHIFT+PROGRAM on the remote control during stop. "PRGM" flashes on the display. 2 Press CD DIRECT on the remote control and then press the numbered button (1-3) within 3 seconds to select a disc. Go to the next step when the tray stops rotating. 3 Press the numbered buttons on the remote control to program a track. To check the program Press f or g repeatedly during stop.
RADIO OPERATIONS Tuning in to preset stations On the unit 1 Press TUNER/BAND to select a band. 2 Press cPRESET repeatedly or turn MULTI JOG. With each press, the station with the succeeding preset number is tuned in. En On the remote control 1 Press BAND to select a band. 2 Press the numbered buttons for the preset number of your desired station. Manual tuning 1 Press TUNER/BAND (BAND on the remote control) repeatedly to select a band (FM or AM.) 2 Press f or g to tune in to a station.
Adjustments Antennas Keep antennas away from metallic objects, electrical equipment and cords. FM antenna: Extend fully and position for the best reception. If receiving condition is poor, connect optional outdoor antenna to FM 75 Ω terminal. Be sure to connect the shield braid of the antenna to the 2 terminal. AM antenna: Rotate to find best reception. En To switch to monaural FM reception Press SHIFT+TUNER MODE on the remote control.
TAPE OPERATIONS To play back type II (High position) tapes Turn MULTI JOG until "SOFT" is displayed while playing a type II tape. Then, the unit provides the optimum playback sound for type II tapes. Notes on cassettes •Use of 120-minute or longer tapes is not recommended since they are extremely thin and easily deformed or damaged. •Take up any slack in the tape with a pencil or similar tool before use. Slack tape may jam in the mechanism.
3 Press wREC/REC MUTE to start recording. When recording a CD or tape, playback starts automatically. When recording input from connected equipment, manually start playback of the source. On the remote control, press REC MODE and then press wREC/REC MUTE within 3 seconds. • You can also change the source by pressing REC MODE repeatedly before pressing wREC/REC MUTE. •Volume or tone adjustment does not affect recording. •"CAN'T REC" is displayed if you attempt to record a tape with the tab broken off.
Programed Edit Recording As you program the CD tracks to record, Programed Edit Recording displays the remaining recording time for each side of the tape, so you can easily select a set of desired tracks within the length of your tape. En 1 Insert the recording tape in DECK 2. 2 Select the CD function and load disc(s). 3 Press SHIFT+CD EDIT/CHECK twice on the remote control. "PRGM" and "EDIT" are displayed and "P C-00" appears on the display.
SOUND ADJUSTMENTS En Super T-BASS TREBLE Emphasizes low frequencies for a powerful sound. Press T-BASS repeatedly to select one of the three emphasis levels (1-3) or the off position (0). Enhances high frequency for sound clarity . Press TREBLE repeatedly to select one of the three enhancement levels (1-3) or the off position (0). •When the sound becomes distorted with the T-BASS effect, cancel it. •When the sound becomes distorted with the TREBLE effect, cancel it.
TIMER OPERATIONS 5 Press f or g to adjust the volume level for timed playback, then press aSET or ENTER. Adjustable range: 0 to 16 6 Prepare the source. To play CD(s), load disc(s). To play the radio, select the band and tune in to the desired station. To play a tape, insert the tape and select the deck. To play external equipment connected to the VIDEO/AUX jacks, set an external timer for the equipment so that its playback begins at the same time. En 7 Press POWER 6STANDBY/ON to turn the unit off.
To display the timer setting Press TIMER. The timer-on time, the source and the timer-activated duration are displayed for 6 seconds. Timer recording Tip: Timer setting can be displayed even while the unit is turned off, and at that time if you press ENTER or a within 6 seconds after TIMER is pressed, you can enter the timer setting mode and change the setting. 1 Press TIMER (SHIFT+TIMER on the remote control) repeatedly until "5REC" appears on the display.
REFERENCE En Care and maintenance Troubleshooting Occasional care and maintenance of the unit and the software are needed to optimize the performance of your unit. If your unit fails to perform properly, check the following guide and the relevant sections of the Operating Instructions. To clean the cabinet Use a soft and dry cloth. If the unit surfaces are extremely dirty, use a soft cloth lightly moistened with mild detergent solution. Do not use strong solvents such as alcohol, benzine or thinner.
GENERAL Specifications MAIN UNIT CX-ND30 TUNER FM tuning range FM usable sensitivity (IHF) FM antenna terminal AM tuning range AM usable sensitivity AM antenna 87.5 MHz to 108 MHz 13.2 dBf 75 ohms (unbalanced) 530 kHz to 1710 kHz (10 kHz step) 531 kHz to 1602 kHz (9 kHz step) 350 µV/m Loop antenna AMPLIFIER Power output Total harmonic distortion Input Outputs Weight 120 V AC, 60 Hz 80 W With ECO mode on: 0.6 W With ECO mode off: 17 W 260 x 324 x 315 mm (10 1/4 x 12 7/8 x 12 1/2 in.) 6.
NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.