Operating instructions

9
En
Changing the display color
You can preset up to 3 of your favorite colors you adjusted. The
display color can be changed to 12 different colors and 3
adjusted preset colors (select color mode). You can also select
12 different colors and 3 adjusted preset colors for each function
(function color mode).
You can select between select color mode and function color
mode.
Presetting select color mode
1 Press COLOR to display "SELECT CL" while the
power is on.
2 Within 4 seconds, turn VOLUME/MULTI JOG until
"COLOR M 1", "COLOR M 2" or "COLOR M 3"
is displayed.
3 Press COLOR.
"AGB" is displayed and "A " flashes.
4 Turn VOLUME/MULTI JOG to select "A ", "G "
or "B ".
- A: adjust amber color.
- G: adjust green color.
- B: adjust blue color.
5 Press COLOR.
6 Turn VOLUME/MULTI JOG to adjust the color.
The level can be adjusted from "00" to "50".
"50" is the brightest level.
7 Press COLOR.
8 Repeat steps 4 to 7 to set the desired color.
9 Press ENTER.
•If power is interrupted for more than approximately 12 hours,
all settings stored in memory after purchase need to be reset.
•If you select "00" in each color, it displays no color on the
display.
•The display color may not change when you adjust only
one of the colors.
Select color mode
1 Press COLOR to display "SELECT CL" while the
power is on.
2 Within 4 seconds, turn VOLUME/MULTI JOG to
select the color.
3 Press ENTER.
Function color mode
1 Hold down COLOR until "F-CL" is displayed.
2 Within 4 seconds, turn VOLUME/MULTI JOG so
that "CL EDIT" is displayed.
3 Press ENTER.
The source name and color number flashes on the display.
If there is no operation for 4 seconds, setting is canceled.
4 Turn VOLUME/MULTI JOG to select a source, then
press ENTER.
5 Turn VOLUME/MULTI JOG to select the color, then
press ENTER.
6 Repeat steps 4 and 5 to determine the colors for
other sources.
7 Press ENTER.
Changing the color mode
1 Hold down COLOR until "F-CL" is displayed.
2 Within 4 seconds, turn VOLUME/MULTI JOG to
select "F-CL ON" or "F-CL OFF".
- F-CL ON: function color mode
- F-CL OFF: select color mode
3 Press ENTER.
If there is no operation for 4 seconds, setting is canceled.
Setting the clock
1 Hold down SHIFT and press CLOCK on the remote
control.
When the unit is turned off, you can also press a or
ENTER.
2 Press f or g to set the time.
Each press changes the time in 1-minute steps.
Holding these buttons down will vary the time in 10-minute
units.
If f or g is not pressed within 4 seconds, setting
is canceled.
•You can also turn VOLUME/MULTI JOG to the right to
advance the time and to the left to move the time back.
The speed with which the time changes varies according
to how fast you turn VOLUME/MULTI JOG.
3 Press a or ENTER.
The time display stops flashing and the clock starts from
00 seconds.
To display the time while the power is on
Hold down SHIFT and press CLOCK on the remote control.
The time will be displayed for 4 seconds.
To switch to the 24-hour standard
Display the time and press s within 4 seconds.
With each press, the clock alternates between 12- and 24-
hour standard time.
Tip:
In the 12-hour standard, "AM12:00" indicates midnight and
"PM12:00" noon.
If the clock display flashes when the unit is turned
off
There has been a power interruption. Reset the clock.