D10CE 10-bit Encoder SDI to Analog Converter User Manual August 25, 2003 P/N 101641-00
Trademarks AJA, Io, and Kona are trademarks of AJA Video, Inc. All other trademarks are the property of their respective holders. Notice Copyright © 2003 AJA Video, Inc. All rights reserved. All information in this manual is subject to change without notice. No part of the document may be reproduced or transmitted in any form, or by any means, electronic or mechanical, including photocopying or recording, without the express written permission of AJA Inc.
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — Introduction Introduction The D10CE converts Component Serial Digital (SDI) to analog Composite and Component outputs—simultaneously. Four analog outputs are provided, plus two equalized and re-clocked SDI loop-through outputs. The D10CE automatically detects and configures to 525 or 625 line component digital input and then outputs analog NTSC (525 line input), PAL (625 line input) or component as configured by an 8-section DIP switch.
Block Diagram DIP Switch User Interface for Feature Selection Serial Video In ReClock 10-bit D/A Converter PLL Jitter Filter Filter COMPOSITE or SYNC COMPONENT OUTPUTS (selected by DIP switch) Clocked Loop-through SDI Outputs Filter COMP B Y Filter Y G Pb Filter C R Pr Serial Video Out 1 Serial Video Out 2 D10CE 10-bit SDI to Analog Component and Composite Converter, Block Diagram I/O Connections SDI Input BNC Composite and Component Output BNCs SDI Loop Output 1 BNC Configurati
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — User Controls User Controls The user interface for the D10CE is an 8-switch DIP accessible through a cut-out in the bottom of the unit. Use the DIP switches to configure outputs, pedestal, blanking, and enable or disable noise reduction. 1 2 3 4 5 6 7 8 Switches 1 through 3 control the COMPOSITE/ SYNC output BNC. Switches 4 through 8 control the video format of the three BNCs below.
Switch 3 Configure Blanking For Composite/Sync BNC : ON OFF WIDE Blanking: Vertical— Line numbers indicate where video starts) line 20, field 1; line 20, field 2 (525 line) line 23, field 1; line 336, field 2 (625 line) Horizontal— Active video line duration ITU-R/SMPTE (710 pixels NTSC, 702 pixels PAL) NARROW (NAR) Blanking: Vertical— Line numbers indicate where video starts line 13, field 1; line 12, field 2 (525 line) line 10, field 1; line 322, field 2 (625 line) Horizontal— Active video line dur
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — User Controls Switch 7 Configure Blanking For Component Output BNCs (3) : ON OFF WIDE Blanking: Vertical— Line numbers indicate where video starts) line 20, field 1; line 20, field 2 (525 line) line 23, field 1; line 336, field 2 (625 line) Horizontal— Active video line duration ITU-R/SMPTE (710 pixels NTSC, 702 pixels PAL) NARROW (NAR) Blanking: Vertical— Line numbers indicate where video starts line 13, field 1; line 12, field 2 (525
Installation Typically, D10CE installation consists of the following: 1. 2. 3. 4. disconnect +5VDC from the convertor configure the DIP switch for the desired equipment configuration and video formats connect video equipment to the convertor BNCs apply +5VDC power to the converter ((AJA power supply model DWP) Specifications Item Specification Serial Input SMPTE 259M 270MB, (SDI) SDI Cable Equalization 300 meter 8281 typical Serial Outputs Equalized, Re-clocked Frequency Response +/- .
AJA D10CE 10-bit SDI to Component/Composite Converter User Manual — Specifications 1 9