Contents Safety Information......................................... 24 Getting Started...................................................... 25 Notifications & Features & Accessories................. 25 Environmental Information ................................... 25 Standby Notifications............................................. 25 Features................................................................ 25 Accessories Included............................................
Safety Information If there is lightning or storms, or if the TV is not going to be used for a while (e.g. if going away on holiday), disconnect the TV set from the mains. The mains plug is used to disconnect TV set from the mains and therefore it must remain readily operable. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Getting Started Notifications & Features & Accessories • AVL (Automatic Volume Limiting). Environmental Information This television is designed to consume less energy to help save the environment. To reduce energy consumption, you should take the following steps: If you set the Power Save Mode as Eco, the TV will switch to energy-saving mode. The Power Save Mode settings can be found in the ‘Picture’ section of the Main Menu. Note that some picture settings will be unavailable to be changed.
To turn the TV off: Press the middle of the button down and hold it down for a few seconds, the TV will turn into standby mode. Inserting the Batteries into the Remote Lift the cover on the back of the remote upward gently. Install two AAA batteries. Make sure to match the + and - ends of the batteries in the battery compartment (observe the correct polarity) Replace the cover.
Getting Started Remote Control 1 / 2 / SOURCE PRESETS 1 2 3 4 5 6 7 8 9 .,/@ 0 1. Standby 2. My button 1 3. Internet browser 4. Equalizer settings mode 5. Picture mode selection 6. Numeric buttons 7. TV Button / Channel list 8. Electronic programme guide 9. Menu 10. Navigation buttons (Up/Down/Left/(Right-TXT Subpage) Q. MENU 11. Back 12. Favourites 13. Volume Up / Down 14. Info EXIT BACK 15. No function . V P V P 16. Play 17.
Getting Started Connections Connector Type Cables Device Scart Connection (back) VGA Connection (back) SIDE AV SIDE AV 5Vdc Max:500mA PC/YPbPr Audio Connection (side) Side Audio/Video Connection Cable (Supplied) PC Audio Cable (Not supplied) HDMI MODE o Connection (back) SPDIF Connection (back) SIDE AV SIDE AV 5Vdc Max:500mA SIDE AV 5Vdc Max:500mA MODE o HEADPHONE Side AV (Audio/Video) Connection (side) AV Connection Cable (supplied) Headphone Connection MODE o (side) PC to YPbPr YPb
Getting Started First Time Installation - USB Connections Cable Installation Switching On/Off To Switch the TV On Connect the power cord to the 220-240V AC, 50 Hz. To switch on the TV from standby mode either: Press the “ ” button, P+ / P- or a numeric button on the remote control. Press the side function switch until the TV comes on from standby. To Switch the TV Off If you select CABLE option and press OK button on the remote control. To continue, please select YES and press OK.
TV Menu Features and Functions Picture Menu Contents Mode You can change the picture mode to suit your preference or requirements. Picture mode can be set to one of these options: Cinema, Game, Sport, Dynamic and Natural. Contrast Sets the lightness and darkness values of the screen. Brightness Sets the brightness value for the screen. Sharpness Sets the sharpness value for the objects displayed on the screen. Colour Sets the colour value, adjusting the colors.
Sound Menu Contents Volume Adjusts the volume level. Equalizer Selects the equalizer mode. Custom settings can be made only when in user mode. Balance This setting is used for emphasizing left or right speaker balance. Headphone Sets headphone volume. Sound Mode You can select a sound mode. (If the selected channel supports). AVL (Automatic Volume Limiting) Function sets the sound to obtain fixed output level between programmes.
Other Settings: Displays other setting options of the TV set: Menu Timeout Changes timeout duration for menu screens. Scan Encrypted Channels When this setting is on, the search process will locate the encrypted channels as well. Blue Background Activates or deactivates the blue background system when the signal is weak or absent. Software Upgrade To ensure that your TV always has the most up to date firmware. Application Version Displays application version.
General TV Operation Using the Channel List The TV sorts all stored stations in the Channel List. You can edit this channel list, set favourites or set active stations to be listed by using the Channel List options. Configuring Parental Settings Connectivity Functions Connecting to a Wired Network • Connect broadband ISP connection ethernet cable to the ETHERNET INPUT of your modem. To prohibit viewing of certain programmes, channels and menus can be locked by using the parental control system.
Connecting to a Wireless Network IMPORTANT: “Veezy 200” USB dongle is required to use wireless network feature. • To make your modem’s SSID visible, you should change your SSID settings via modem’s software. The TV cannot connect to the networks with hidden SSID. For connecting to a wireless LAN network, you should perform the following steps: 1. Connect broadband ISP connection ethernet cable to the ETHERNET INPUT of your modem. 2.
Press YELLOW button to scan wireless network. Afterwards, available network list will be displayed. Please select your desired network from the list. If the selected network is protected with a password, please enter the correct key by using the virtual keyboard. You can use this keyboard via navigation buttons and OK button on the remote control. Wait until the IP the address is shown on the screen. This means that the connection is now established.
Step 3: Play Shared Files via Media Browser Select Media Browser by using Left or Right button from the main menu and press OK button. Media browser will be then displayed. DLNA support is available only with Media Browser folder mode. To enable folder mode, go to Settings tab in the main media browser screen and press OK. In the settings options, highlight View Style and change to Folder using Left or Right button. Please select desired media type and press OK.
PC Input Typical Display Modes AV and HDMI Signal Compatibility The following table is an illustration of some of the typical video display modes. Your TV may not support all resolutions. Your TV supports up to 1920x1080.
No sound Software Upgrade Your TV is capable of finding and updating automatically via the Aerial/Cable signal or over the Internet. • Has the TV been set to mute? To cancel mute, press the “ ” button, or increase the volume level. Software upgrade search via user interface • Sound is coming from only one speaker. Is the balance set to one extreme? See Sound Menu section. Simply navigate on your main menu. Choose Settings and select Other Settings menu.
Internet Browser To use the internet browser, please select the internet browser logo from the portal section. Refresh Home Page Address Bar Add History Bookmarks Zoom Previous Next Settings Remote control shortcuts (Zoom in-out/Back/Home) Quick Access • To navigate the web browser, use the arrow buttons on the remote control. Press OK to continue. pages and these will take you to the appropriate pages.
Getting Started with Skype Make voice calls and video calls with Skype on your TV. Select the Skype app from the portal section to start a conversation. Follow the on screen instructions to see how to operate related features. NOTE • Connect your supported webcam directly to the USB port on your TV. • If the camera is not working properly, switch off and unplug the TV. Connect your camera again and turn the TV on. • As soon as the TV is turned off, Skype disconnects.
Sign In & Sign Up Now To use the Skype application, you need a Skype account. You can create a Skype account, using this app, in the ‘Sign In & Sign Up Now’ menu if you don’t already have one. If you already have a Skype account, enter your name and password correctly. Select Sign In and press OK. If you have a Skype account and you forgot your password, press the Red button to view the “reset password” screen. After successfully logging in to your account, the contact list will be displayed on screen.
Adding a contact By pressing the button select the “Search Contacts” option. Enter the full name, skype name or email address of the contact you want to find and add. Use the remote control or virtual keyboard to enter a keyword. Recent history Incoming call Outgoing call Missed call Icon meaning Your Skype history can be seen in this section. To view recent history options, use the p+ and p- buttons. To delete a conversation, press the Red button.
Actions Account Name, mood message and profile picture. Online status Select a Menu by pressing the button. Your contact list (Press Ok to use video&voice call) Help bar Select a person from the contact list screen and press OK. Choose an action from the list and then press OK to start the selected process. Voice and video call is ready for your use. If available you will see the thumbnail view of yours and the other person’s camera feed.
Incoming call The incoming call dialog is shown when you are logged into Skype and when other users initiate a Skype call. A small dialog box will appear in the lower right corner of the TV screen whether the user watches TV or is browsing through Skype. Use the remote control button and choose your action. Dialing Phones The option to call phones is available if you have Skype Credit. Please buy credit first. Afterwards, select a country then enter a phone number which you want to call.