CONTRAST REC GAIN MAIN VOLUME GAIN HIGH LOW SETUP SEQUENCE Q1 Q2 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 MAX MIN PAD BANK B A D C NEXT SEQUENCE F E TRACK MUTE 7 8 SAMPLE I J MULTI L MIN MAX A MIN ACTIVE B C D E F G H 5 6 1 2 3 PROGRAM K MIXER EFFECT M SAVE N GLOBAL LOAD MAX ACTIVE DRUMS O Q-LINK SEQUENCE PA D 13 P LOOP PA D 14 P TO PA D 15 P FROM PA D 16 P Q MISC.
# SAFETY INSTRUCTIONS # INFORMATIONS 1. Parts identified by the } symbol are critical for safety. Replace them only with the parts number specified. 2. In addition to safety, other parts and assemblies are specified for conformance with such regulations as those applying to spurious radiation. These must also be replaced only with the specified replacements. Examples : Noise blocking capacitors, noise blocking filters, etc. 3. Use specified internal wiring.
I. SPECIFICATIONS General Sound Generator Power supply 100-240V AC 50/60Hz 70W (27W without options) Dimensions Weight 526 (W) x 170 (H) x 453 (D) mm (with LCD tilted down) 10.5kg (without options) Display 320 x 240 dots grey-scale graphical LCD w/back light Sampling rate Data format 44.1kHz, 48kHz, 96kHz 24/16 bit linear Sampling time 180/120 (16/24 bit) seconds mono FS=44.
II. DISASSEMBLY In case of trouble, etc., necessitating dismantling, please dismantle in the order shown in the illustrations. Reassemble in the reverse order. 1.
ZS-821548X SCREW TOP COVER NI ZS-331182 BT BID30X08 STL BNI ZS-331182 BT BID30X08 STL BNI SERVICE MANUAL 5
ZS-331182 BT BID30X08 STL BNI SERVICE MANUAL 6
III.
IV. OS Update Procedure OS Update Procedure [OS Update procedure from USB] The OS update can be made from the PC via the USB port. You must have the “OS loader software for MPC4000” besides the OS .bin file. The OS loader software includes the OS Loader.exe file, USB driver.inf file, and USB Driver.sys file. 1. Install USB Driver to your PC After all files are un-Zipped, place the USB Driver.inf and USB Driver.sys files into the same folder, e.g. Driver.
V. TEST MODE Panel Test Mode To enter the Panel Test Mode, press the GLOBAL key while holding down the SHIFT key in the GLOBAL page [F1] of the GLOBAL Mode. • Moving the Q-link knobs changes the graphics accordingly. • Tapping the PAD shows the amount of pressure applied on the bar graph. • Switching the FOOT Pedal on/off changes the graphics accordingly. • Turning the JOG wheel increases/decreases the value in the Data field. • Pressing the key shows its name at the bottom of the screen.
VI. PARTS LIST ATTENTION 1. When placing an order for parts, be sure to list the Part No., Model No. and the description of each part. Otherwise, the non-delivery of the part or the delivery of a wrong part may result. 2. Please make sure that Part No. is correct when ordering. If not, a part different from the one you ordered may be delivered. 3. Since the parts shown in Parts List or Preliminary Service Manual may have been the subject of changes, please use this Parts List for all future reference.
PC BOARD BLK The PC Board Block may contain several PC Boards. They appear under its block name with their individual part number. 1. P.C. BOARD BLOCK Ref.No. 1 Part No. BA-L6052A020A Description PC CPU BLK Z8 2 3 BA-L4016A020A BA-L4016A030A PC (#) IO BLK MPC4000 PC OPERATION BLK MPC4000 4 BA-L4016A040A PC (#) OTHER BLK MPC4000 PC (#) IO BLK CONSISTS OF FOLLOWING P.C. BOARDS.
Ref.No. R23 Part No. ER-812771J Description R OMF V T05FS ERX12SE1/2W 1R0J Ref.No. J27 Part No. EJ-821386X Description PHONE J YKB22-5264 NUT 6.3 R77 TR1 ER-821483X ET-429896J R OMF H S15 FS ERG2SH 2W 820J TR C.DTA144EKA T146T08E R361 RL1 ER-422512J EQ-348929 R OMF H S15 FS ERG2SH 2W 151J RELAY SIG G5A-237P 2TR 12V TR2 TR3 ET-429897J ET-434246J TR C.
Ref.No. D135 Part No. ED-811455J Description D SILICON H 1SS133T-77 T26 Ref.No. D305 Part No.
Ref.No. SW135 Part No. ES-349474 Description SW TACT SKHHAM004A Ref.No. D175 Part No.
Ref.No. X1 Part No. EI-820992X Description OSC X'TAL C.DS0751SV 25.0000MHZ Ref.No. Part No.
Ref.No. 12 SW 13 BUTTON Part No. ES-415015J SB-821550X Description SW TACT SKQEAD BUTTON PUSH B(5) [ White ] Ref.No. 47 Part No.
FINAL ASSEMBLY BLOCK 2 13 6 7 1 68 17 16 18 11 4 CONTRAST REC GAIN 22 MAIN VOLUME 23 GAIN HIGH LOW SETUP SEQUENCE Q1 Q2 F1 F2 F3 F4 F5 F6 F1 F2 F3 F4 F5 F6 D C NEXT SEQUENCE F E TRACK MUTE 7 8 MIN B MAX MIN ACTIVE C D E F G H SAMPLE I J MULTI 9 4 5 6 1 2 3 PROGRAM K MIXER EFFECT M SAVE N LOAD GLOBAL MAX ACTIVE DRUMS O Q-LINK SEQUENCE 21 PA D 13 P LOOP PA D 14 P TO PA D 15 P FROM PA D 16 P SONG Q MISC.
FINAL ASSEMBLY BLOCK 31 42 43 35 38 39 34 37 41 51 33 40 36 32 37 45 48 29 46 47 44 28 30 50 49 55 56 53 52 54 ZS-418538J SERVICE MANUAL 18 ZS-417137
LCD BLOCK 3 ◎ ◎ ○ 5 ○ ◎ 4 2 1 3 9 16 7 6 14 15 8 13 11 12 10 SERVICE MANUAL 19
VII. INFORMATION OF ICs 1. IC Explanation. 1-1 IC1 SA1110B (Intel CPU) 206MHz version chip. CPU clock : 176.9MHz. SDRAM (CPU work memory) : 88.45MHz (=176.
Signal name TxD_C SCLK_C SFRM_C LDD[7:0] L_BIAS L_PCLK L_LCLK L_FCLK TXTAL ROM_SEL SMROM_EN /PIOR,/PIOW /IOIS16 TCK_BYP TESTCLK GP10,/PCE1 /PWAIT BATT_FAULT VDD_FAULT VDD VDDX VSS VSSX Dir in in in out out out out out in in in out in in out - Explanation CD digital recognition. Low=connected.(MPC only) BM1. Machine recognition. Low=Z4/8. High=MPC. BM0. Connected GND now. for future. LCD controller display data. LCD ac bias drive. LCD pixel clock. LCD line clock. LCD frame clock. Not used.
1-6. IC8 XC95144XL-7TQ100C (Complex programable logic (CPLD). Address decoder. Expansion port by using data-latch. Communication logic for RTC. Selector. 1-6-2.
Signal name /FP2_PROG PLD2_TMS PLD2_TDI PLD2_TDO TCK,TMS,TDI TDO VCCINT VccIO GND Dir out Explanation For configuration to FPGA on ADAT PCB. out For configuration to CPLD on DIO. in in out - For configuration to CPLD on DIO. For configuration.(TCK is also used for CPLD on DIO) For configuration. Positive supply for internal logic. +3.3V Positive supply for output driver. +3.3V Ground supply. 1-7. IC9 XC2S100-5TQ144C (Field Programmable Gate Arrays (FPGA)) IDE controller.
1-8. IC10 SL811HST (USB Host/Slave Controllers). 1-8-2. Pin Descriptions Pin No. 3 4 5 6 7 8 9 16 17 18 19 21,39 27-29 31-33 40 42 43 44 45 15,41 9,20 30 Signal name /WR /CS CM USBVDD DATA+ DATAUSBGND CLK/X1 X2 /RST INTRQ Dir in in in i/o i/o in out in out Explanation Write Strobe. Active low. Chip select. Active low. Clock mode. H: at 12MHz. L: at 48MHz clock source. Power for USB Transceivers. USB Differential Data Signal High Side. USB Differential Data Signal Low Side. Ground Connection for USB.
1-9. IC11 FAS236U (SCSI Controller) 1-9-2. Pin Descriptions Pin No. 100 1 2 4 5 6 7 8-15 19-26 16,27 29-36 37 42-45 48-51 52 56 57 58 59 62 63 64 65 66 69 70 71 72 73 74,75 76 77 79 80 81 82-85 86 87 90-93 96-99 38,88 17,18,40 41,46,47 54,55,60 61,67,68 94,95 Signal name DREQ /DACK /DBWR IGS DIFFSENS TGS EDIFFS Dir out in in out in out in Explanation DMA request. H: ready to transfer data. DMA acknowledge. Data-bus write control. Indicates that chip is acting in initiator mode. H: differential mode.
1-10 IC12, 16 ALVCH16245 (16 bit Bus bidirectional transceivers) 1-11 IC13-15 ALVCH16244 (16 bit Bus Buffers) 1-12 IC17, 18 LVC244 (8 bit Bus Buffers) 1-13 IC19 LVC245 (8 bit Bus bidirectional transceivers) In particular, this is used for changing 5V into 3.3V. 1-14 IC20 M51957B (System Reset IC. Delay time is about 0.34 sec) 1-15 IC21, 22 NJM317 (Regulator IC) IC21: regulate +2.5V for FPGA. IC22: regulate +1.75V for CPU. 1-16. IC23 NET2890 (USB function controllers) 1-16-2.
Appendix: Installing storage devices (for service engineers) This appendix explains how to install storage devices (ATA hard disk, CD-ROM drive, Zip drive, etc.) in the MPC4000. Check the included items The following items are included with the MPC4000 for use when installing storage devices. Check to make sure that no items are missing.
3. Remove the screw (located in the center of the front panel) that fastens the top panel from the lower front side. 4. Remove the screw (located in the center of rear panel) that fastens the top panel from the rear side. 5. Use both hands to lift the protrusion on the front of the top panel, and open the top panel.
6. Use a metal rod or similar object as a prop inside the chassis to hold up the top panel. The side panels and screws you removed must be kept in a safe place. To close the top panel, re-tighten the screws in the opposite order to which they were removed. Installing a drive 1. If you are installing a removable-media drive such as a CD-ROM drive or Zip drive, remove the blank panel from the front panel. 2.
When installing a drive in the 5 inch bay Bracket (L) PC IO PC IO AD_DA P23 P7 P8 P2 PC CPU Cable connections Connecting the flat cable 1. Remove two screws from the cover that conceals the PC CPU board. When you remove the cover, you will see the P2 connector for the ATA drive. Bracket (S) PC IO AD_DA P7 P8 PC IO P2 Step 1 PC CPU 2. 3Insert the blue connector of the included flat cable into the P2 connector of the PC CPU board. 3. Reattach the cover that you removed. 4.
Connecting the power cable 1. Insert the connector of the included power cable into the P7 connector or P8 connector of the PC I/O board. Use the power cable with the ferrite core if you are installing a hard disk. Use the power cable without a ferrite core if you are installing a Zip drive or CD-ROM drive. 2. Connect the other end of the power cable to the drive.
! Installation - MPC4000 1. Remove the fixing screws of the MPC4000 Side Panels (4pcs. on each side) and remove Side Panels. Next, remove the screws (5pcs. on each side) hidden by the Side Panels and then remov e the center screws (2pcs.) located underneath the Armrest and the topmost of Rear Panel. The Top Panel Block can be swing-opened by lifting the Armrest from the front. Save the removed screws. 2. Remove the fixing screws (4pcs.
! Installation - MPC4000 1. Remove the fixing screws of the MPC4000 Side Panels (4pcs. on each side) and remove Side Panels. Next, remove the screws (5pcs. on each side) hidden by the Side Panels and then remove the center screws (2pcs.) located underneath the Armrest and the to pmost of Rear Panel. The Top Panel Block can be swing-opened by lifting the Armrest from the front. Save the removed screws. 2. Remove the fixing screws (2pcs.) for the Mask Plate on the Rear Panel and remove the Mask Plate.
! Installation – MPC4000 1. Remove the fixing screws of the MPC4000 Side Panels (4pcs. on each side) and remove Side Panels. Next, remove the screws (5pcs. on each side) hidden by the Side Panels and then remove the center screws (2pcs.) located underneath the Armrest and the topmost of Rear Panel. The Top Panel Block can be swing-opened by lifting the Armrest from the front. Save the removed screws. 2. Remove the fixing screws (4pcs.
1-3, Hiranuma 1-Chome, Nishi-Ku, Yokohama, Japan SERVICE SECT.
MPC4000 OPERATION BLOCK DIAGRAM
MPC4000 PC IO BLOCK DIAGRAM
MPC4000 AD DA BLOCK DIAGRAM
5 4 3 2 1 SEND[0..5] B-RET12 B-RET13 B-RET14 F1 D171 GMA01 F2 D172 GMA01 F3 D173 GMA01 F4 D174 GMA01 3pcs RED SW176 1 2 F5 D175 GMA01 B-SEND5 F6 D176 GMA01 B-SEND4 MULTI D148 GMA01 SW140 1 2 SW141 1 2 SW142 1 2 7 D140 GMA01 8 D141 GMA01 9 D142 GMA01 SW134 1 2 SW135 1 2 SW136 1 2 4 D134 GMA01 5 D135 GMA01 6 D136 GMA01 SW143 1 2 SW144 1 2 SW145 1 2 MIXER D144 GMA01 E.PRG D145 GMA01 SW137 1 2 SW138 1 2 SW139 1 2 STEP E.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 D+5V D+5V PH 4P R5 220 12 DGNG MSPEED C55 47/25 74HCT32 IC13D 74HCT32 A R30 0.047 C66 C65 0.047 C69 0.047 DSS306-101 FL15 DSS306-101 FL14 FL12 DSS306-101 FL11 DSS306-101 Vcc 3 D2 1SS133T 6 5 4 PC400 C89 4.7/50 D8 1SS133T 5 R96 E R93 10K C90 C83 10u 0.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A A A+12V A+12V C62 3.3/50 C61 C63 3.3/50 2700PF A+12V B DA_RST 2 IC10A 8 22/50 LRCK DA_BCK SOUT12 DA_MCLK 220 R3 220 R4 C20 0.047 C RST ZEROL ZEROR LRCK DATA BCK SCKI DGND VDD DEMP0 DEMP1 FMT0 FMT1 FMT2 VCC3 AGND2 IOUTLIOUTL+ VCC2 VCC1 VCOM3 IREF VCOM2 VCOM1 AGND1 IOUTR+ IOUTRMUTE 10/50 220 220 R60 3900p R1 R2 4 A-12V C22 C21 IC9 1 2 3 4 5 6 7 8 9 10 11 12 13 14 R63 750 1.
7
5 4 3 2 1 N: Blue ! AC INLET SOT-16 PC(# )IO C5 MKP3362 683M 2 1 L4016A502B 1 'MAIN&REC VOLUME' L1 HR-24-562 PC(# )OTHERS L4016A504E 'FILTER' ! C6 MKP3362 103M ! 3 P4 P3 4 2 ! 2 FAN MOTOR PC 4ADT(ADAT) PC 48P(8para OUT) L5263B5010 L5261B5010 W3 109R0612F402 L=230 WIRE ASSY L5263(2) PH 8P J3 P1 P1 WIRE ASSY L5261(1) RA-RC 26P WIRE ASSY L5263(1) RA-RC 50P ! WIRE ASSY L4016(16) OUPIIN 26P 2 2 1 1 ! SW10 SDDF3A ! P2 P4 L6052A5060 W1 'POWER SW' PC(# )IO P7 For O
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 A A A+12V CD ON LINE ON A+12V 6 LCOLD TR10 2SC3329 D13 1SS133 C106 R106 3.3K 5 100P 4 A-12V TR11 2SC3329 C114 IC22B 8 7 10K M5520L C126 R136 10/50 300 C118 R191 2 R193 10K R194 10K R140 470K M5220L R141 91K J23 SL 1000/6.3 R170 10K TR12 2SC3329 4 A-12V R145 18K R144 300K C133 3900pF C132 TR13 2SC3329 P23 GND L_CD GND R_CD PH_2P D14 1SS133 R133 750 0.
PC IO VR BLK PC IO VR BLK
PC IO BLK
PC IO BLK
PC IO ADDA BLK PC IO ADDA BLK
PC LCD BLK
