UNDER CABINET RANGE HOOD Universal Installation Instructions and Use & Care Guide For questions about features, operation/performance parts, accessories or service, call: 1-626-453-0550 Model: Y01 W01 IMPORTANT: READ AND SAVE THESE INSTRUCTIONS. FOR RESIDENTIAL USE ONLY. Revised September 2014 Disclaimer: Item purchased may be slightly different from the manual.
TABLE OF CONTENTS RANGE HOOD SAFETY ....................................................................2 INSTALLATION REQUIREMENTS ...................................................4 Tools and Parts Requirements ...................................................4 Location Requirements .............................................................4 Installation Dimensions ............................................................5 Ventilation Requirements .................................................
IMPORTANT SAFETY INSTRUCTIONS WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, READ THE FOLLOWING: ■ Use this unit only in the manner intended by the manufacturer. If you have questions, please contact the manufacturer. ■ Before servicing or cleaning the unit, switch the power off and lock the service panel. This will prevent the power from accidentally turning on. If the service panel does not lock, secure a warning label, such as a tag, to the service panel.
INSTALLATION REQUIREMENT TOOLS AND PARTS REQUIREMENTS Electrical drill or ratchet driver 1/2” drill bit for drilling pilot holes 1 ¼” drill bit for drilling electrical wiring access hole.
INSTALLATION DIMENSIONS A. B. C. D. Countertop height Hood height from ceiling to bottom of the range hood filter surface: D-A-C=B 29” (73.66 cm) min. from cooking surface, suggested 31” (78.74 cm) max.
VENTILATION REQUIREMENTS ■ Range hoods must be ventilated to the outdoors ■ Do not ventilate the range hood into an attic or other enclosed areas. ■ Do not use 4" (10.2 cm) laundry-type wall caps. ■ The length of the range hood and the number of elbows should be kept to a minimum to provide maximum performance. For the most efficient and quiet operation ■ Use no more than three 90°elbows. ■ Make sure there is a minimum of 24" (61 cm) of straight duct between the elbows if more than one elbow is used.
Calculating Vent System Length To calculate the length of the system you need, add the equivalent feet (meters) for all vent pieces used in the system. ELECTRICAL REQIUREMENTS Observe all governing codes and ordinances. Ensure that the electrical installation is adequate and in conformance with the National Electrical Codes, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition), all local codes, and ordinances.
INSTALLATION INSTRUCTIONS PREPARING THE LOCATION ■ It is recommended for the vent system to be installed before hood is installed. ■ Before making cutouts, make sure there is proper clearance from the range hood to the cook top. ■ Check your cabinet’s height and the hood height available for your ceiling before selecting your hood. 1. Disconnect the power. 2. Determine which venting method to use: roof, wall, or back. RANGE HOOD MOUNTING SCREWS INSTALLATION 1.
Air Flow Flapper Preparation 5. Mark the flappers location under the cabinet. 6. Cut out a rectangle a little bit larger than the air flow flapper under the cabinet. Also, cut out a circle where the white, green, and black wires would be. Complete Preparation 1. Determine and make all necessary cuts in the wall for the vent system. Install the vent system before installing the hood. See Page 6 “Ventilation Requirements” Section. 2.
STEP 1: CONNECTING VENT SYSTEM Air Flow Flapper Installation 1. Install the non-return air flap on top of hood with M5 X 8 screws (Part B). 2. Remove the tape from the air flow flappers.
STEP 2: MOUNTING THE RANGE HOOD 1. After preparing the location, use two or more people, hang the range hood on the 8 mounting screws (Part A), installed during preparations (Look at page 8), through the mounting slots on the top of hood (Part B1). Excessive Weight Hazard Use two or more people to move and install range hood. Failure to do so can result in back or other injury. 2. Level the range hood and tighten inner M5 X 45 mounting screws (Part B2). 3. Tighten the 4 M5 X 12 screws after (Part C).
STEP 3: ELECTRICAL CONNECTION 1. Connect the three prong cable (not included) to the existing cable on the range hood. 2. Connect the White to White, Black to black, and Green ground to green ground by either a solder or with a connection piece. DO NOT FORGET TO GROUND THE CONNECTION SAFETY WARNING: Risk of electrical shock. This range hood must be properly grounded. Make sure this is done by a qualified electrician in accordance with all national and local electrical codes.
RANGE HOOD USE The range hood is designed to remove smoke, vapors, and odors. For best results, start the hood before cooking. After, the cooking process is complete, allow the range hood to run for several minutes to completely clear all the smoke and odors from the kitchen. A. Return Air flapper B. LED/Halogen lights C. Control Panel D.
RANGE HOOD CONTROLS Operating the lights The On/Off light button controls both lights. Press once for “ON” and again for “OFF”. Operating the blower The “Speed” button turns the fan on and controls the fan speed and sound level for quiet operation. The speed can be changed anytime during the fan operation by pressing the desired blower speed button. The “OFF” button turns the fan off. Disclaimer: Control panel may vary from model to model; models may not have these controls at all.
RANGE HOOD CARE Cleaning IMPORTANT: Clean the hood and grease filters frequently according to the following instructions. Replace panel filters before operating hood. Exterior Surfaces To avoid damage to the exterior surface, do not use steel wool or soap-filled scouring pads. Always wipe dry to avoid water marks. Cleaning Method Use liquid detergent soap and water, or all-purpose cleanser. Wipe with damp soft cloth or non-abrasive sponge, then rinse with clean water and wipe dry.
Replacing the LED/Halogen light Turn off the range hood and allow the LED/Halogen to cool. To avoid damage or decreasing the life of the new bulb, do not touch bulb with bare fingers. Replace bulb using tissue or wearing cotton gloves to handle bulb. If new LED/Halogen light does not operate, make sure the lamps are inserted correctly before calling service. For replacement please visit our website www.shoprangehoods.com .
TROUBLE SHOOTING Potential Effect of Failure Lamp does not turn ON FAN does not work Potential Cause(s) Recommended Action(s) Electronic Control does not work. Due to Over Voltage a) Pressing any key the LCD lights up and icons are in place? Yes, Proceed with the following diagnostic sequence No, Replace the control and user interface. Non functional lamp 1) Remove the lamp. 2) Verify the lamp to be non functional reviewing that the filament is not burned and be in correct place.
in the white plastic. - Push inwards the motor/lamp connectors until the locking system on connectors is well attached. 5) Connect hood to power supply and verify. The blower is too noisy Filters are dirty 1) Verify that the grease and/or charcoal filters are clean. 2) If they are not clean change charcoal filter, or wash grease filter and verify. False contact in the connectors During the hood cleaning, the motor connector has been loose and a false contact in the main harness is performed.
SHOPRANGEHOODS.COM MAJOR APPLIANCE WARRANTY LIMITED WARRANTY For three year from the date of purchase, when this major appliance is operated and maintained according to instructions attached to or furnished with the product, Www.shoprangehoods.com will pay for Factory Specified Parts. This limited warranty is valid only in the United States or Canada and applies only when the major appliance is used in the country in which it was purchased.
