Owner’s Manual Stainless Steel Range Hood Island Mounts: Type A Only Copyright ShopRangeHoods.com© 2016 Office: +1 (626) 321-9834 Email: support@shoprangehoods.com Distributed by ShopRangeHoods.
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer at the address or telephone number listed in the warranty. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
TOOLS & PARTS REQUIREMENTS LOCATION REQUIREMENTS VENTILATION REQUIREMENTS Electrical drill or ratchet driver 1/2” drill bit for drilling pilot holes 1¼” drill bit for drilling electrical wiring access hole Screwdrivers: Philips & Straight blade Pliers Tape measure or ruler and pencil Electrical supplies for wiring Aluminum foil tape and/or HVAC tape Hammer Jigsaw or saber saw Stud finder PARTS SUPPLIED Body & Main Unit: 1 pc. Chimney Mounting Bracket: 1 pc.
Recirculating Installations & Carbon Filters Non-Vented (Recirculating) Installations Carbon Filter Care Guide Ordering Carbon Filters If it is not possible to vent cooking fumes and vapors to the outside, the hood can be used in the non-vented (recirculating version, fitting a carbon filter at the motor. Fumes and vapors are then recycled through the top grille. Do not block the chimney holes and vents on either side.
Cleaning & Maintenance Cleaning Mesh or Baffle Filters Types of Metal Filters Interior Range Hood Cleaning Mesh and baffle filters can be cleaned with regular household dish washing soap and hot water. Please wear gloves while cleaning filters to protect against scrapes or cuts. Exercise caution around sharp metal edges and corners. Mesh The unit must be turned off before being cleaned. Also avoid spraying cleaner directly onto the light bulb or light bulb socket.
AKDY Island Mount Range Hood: Type A (L-Brackets) Installation Steps: 1-8 For best results, please watch our accompanying installation video on YouTube: https://www.youtube.
AKDY Island Mount Range Hood: Type A (L-Brackets) Installation Steps: 9-16 For best results, please watch our accompanying installation video on YouTube: https://www.youtube.
AKDY Island Mount Range Hood: Type A (L-Brackets) Installation Steps: 17-24 For best results, please watch our accompanying installation video on YouTube: https://www.youtube.
Adjusting the Clock Control Panel: Type A Control Panel: Type B1 Clock Setting: Type A Step 1: Tap and hold for 3 secs. Step 2: Tap repeated to set the hour. Step 3: Tap to switch to mins. Step 4: Tap again repeatedly to set the mins. Step 5: Tap again to finish. Clock Setting: Type B Step 1: Tap and hold for 3 secs. Step 2: Tap OR repeatedly to set the hour. Step 3: Tap OR to switch to mins. Step 4: Tap OR again repeatedly to set the mins. Step 5: Tap again to finish.
Adjusting the Clock Control Panel: Type D Clock Setting: Type D Step 1: Tap and hold Control Panel: Type E for 3 secs. Step 2: Tap OR repeated to set the hour. Step 3: Tap to switch to mins. Step 4: Tap OR Step 5: Tap again to finish. repeatedly to set the mins. Clock Setting: Type E Step 1: Tap and hold for 5 secs. Step 2: Tap *If your control panel is not listed, please contact us: support@shoprangehoods.com | +1-626-321-9834 Step 3: Tap repeated to set the hour.
RETURNS & WARRANTY RETURNS, DAMAGES, MISSING PARTS We thank you for your purchase. If you are not satisfied with your purchase or have an issue with our product, please kindly let us know. Our full returns policy is outlined below. Carefully read over our terms before contacting us. If you have questions, our customer service team can be reached at: +1 (626) 321-9834 or support@shoprangehoods.com.
