Installation Sheet

ManualsBrandsAker ManualsPlumbingCM 60 AcryIX 75-1/2" High x 60" Wide x 33" Deep Alcove Shower Tub Module with Right Drain and Above Floor Rough-In

GUIDELINES

FOR UNIT

INSTALLATION

These guidelines are recommended by

Aker Plastics Company Inc. (hereafter

“MAAX”) for the proper installation of their

product. A careful review of these procedures

(and any referenced publications) before

starting is important in avoiding unnecessary

problems resulting in an improper assembly

or installation.

NOTE: All drawings in this publication are

typical, and may appear different than the

actual items being installed. In addition,

optional items may be shown on the units

which may not have been ordered on the

unit being installed.

ON WHIRLPOOL EQUIPPED MODELS,

A SEPARATE SET OF INSTRUCTIONS

IS PACKED WITH THE UNIT FOR THE

WHIRLPOOL SYSTEM. READ THEM

BEFORE INSTALLING UNIT!

WARNING!

NEVER LIFT OR HANDLE WHIRLPOOL

BY SYSTEM PIPING AT ANY TIME.

LIFTING THE UNIT BY THE PIPING CAN

CAUSE SYSTEM DAMAGE.

Special Notes to Installer

!It is the sole responsibility of the installer

to determine, prior to the installation, the

requirements necessary for compliance

with all codes involving the unit or the

installation!

!All paperwork packaged with the unit and

any associated options or accessories

should be saved and presented to the

homeowner upon completion of the

installation!

!HANDLE THE UNIT BY THE SHELL

ONLY! Never lift any unit by attachments

or piping on the shell.

!All published unit dimensions are for

reference only. Any critical dimensions

required for installation should be

taken directly from the unit being

installed!

!Any independent changes made to the

unit (or to any options and accessories

supplied with the unit) beyond those

required for normal installation can void

all warranties! (Refer to warranties for

further information.)

A careful check of the unit should be

conducted upon receipt. Notify your

supplier immediately if any questions or

problems are encountered during this

process.

DO NOT INSTALL ANY UNIT

WITHOUT FIRST ADDRESSING

QUESTIONS WHICH ARISE DURING

THE INSPECTION!

Basic Module Check

Check that the unit drain corresponds to

the bathroom drain location.

Check for unit surface damage.

Check unit color for coordination to

other bathroom fixtures.

Check for proper options and

accessories.

Whirlpool and Accessories Check

An individual system check list is included

in the assembly and operational guidelines

packaged with whirlpool equipped models

and various accessories. Refer to the listed

publications for further information before

continuing.

Inspection Guidelines

Page 1

0703 10023045

141000

CM-60 R

CM-60 L (Shown)

141004

GB-60 R

GB-60 L (Shown)

Tub-Shower Modules

141000 141004

CM-60 R/L GB-60 R/L

Summary of content (6 pages)

PAGE 1
Page 1 Tub-Shower Modules 141000 141004 GUIDELINES FOR UNIT INSTALLATION CM-60 R/L 141000 141004 CM-60 R CM-60 L (Shown) These guidelines are recommended by Aker Plastics Company Inc. (hereafter “MAAX”) for the proper installation of their product. A careful review of these procedures (and any referenced publications) before starting is important in avoiding unnecessary problems resulting in an improper assembly or installation.
PAGE 2
Page 2 GUIDELINES FOR UNIT INSTALLATION Figure 1 - Unit Data, Dimensional and Alcove Framing Guidelines (Tolerance: +0/ -3 /8 inch) HEADER DETAIL Ceiling NOTE: Left End Drain Installation Illustrated Header for Optional Cap Illustrated (required only for units installed with cap) Dbl.
PAGE 3
Page 3 GUIDELINES FOR UNIT INSTALLATION Framing Requirements Due to individual site variations, exact guidelines for every situation cannot be supplied. The recommended framing and dimensional requirements shown are for a typical application and may vary, depending on site requirements. The dimensions shown in Figure 1 are from the surfaces where the unit will be attached. This surface can be bare studding, dry wall or other suitable underlayment material.
PAGE 4
Page 4 GUIDELINES FOR UNIT INSTALLATION ON WHIRLPOOL EQUIPPED UNIT ! Check for required modifications to framing due to whirlpool components. The unit must be positioned square in the alcove framework. The use of shim or filler material behind the fastening flange at each framing member may be required to maintain the unit in the proper position.
PAGE 5
Page 5 GUIDELINES FOR UNIT INSTALLATION Unit Surface Care WARNING! AVOID APPLYING WAX TO THE UNIT BOTTOM! • Mold/Mildew: Liquid mildew remover or baking soda and water paste. Apply paste and allow to fizz several minutes. (Rinse surface thoroughly.) • Routine Cleaning: Mild, non-abrasive cleaner specifically formulated for gelcoat and acrylic surfaces recommended. (Rinse surface thoroughly.) • Construction Adhesive: Soften adhesive with hand held dryer and peel off adhesive.
PAGE 6
Page 6 GUIDELINES FOR UNIT INSTALLATION LIMITED WARRANTY Aker Plastics Company Inc. (hereafter "Aker") offers the following express limited warranty on each of its products. This warranty extends only to the original owner/end-user for personal household use. For commercial uses, additional limitations apply.