WLS 8060 MAX Wireless Loudspeaker System Bedienungsanleitung User Instructions
Table of Contents Page 0. FCC Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2. Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.1. Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2. Potential Risks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WLS 8060 ”MAX” 1. Introduction The WLS 8060 ”MAX” is a high quality powered loudspeaker for a wide range of applications. It allows you to set up a mobile or fixed sound system quickly and easily. This professional design is easy to use even if you are not familiar with the intricacies of sound reinforcement. A clear control layout and rugged case make the WLS 8060 ”MAX” a user-friendly tool for every sound system application.
15 15 9 7 1 10 11 12 6 5 14 7 13 3 Abb.
WLS 8060 ”MAX” 1. RECHARGE BATTERY DC input jack for charging the integrated battery or operating the WLS 8060 on AC power using the supplied AC adapter. 2. Charging LED This yellow LED will light constantly while the battery is being charged and will start flashing as soon as the battery is fully charged. 3. POWER switch Switches power to the WLS 8060 audio section and amplifier ON and OFF but does not affect the charging circuit. 4.
2. Tighten the fixing nut on each antenna CW. 3. Point both antennas upward so that the two antennas will form a ”V”. If you cover the WLS 8060 with the optional RP 6060 rain cover point the antennas straight down. 5.4. Powering Up (Battery Operation) The WLS 8060 has been designed primarily for battery operation. Before first operating the WLS 8060 or if the unit has not been connected to AC power for more than a year, charge the battery for 18 hours. 1.
WLS 8060 ”MAX” CHANNEL 3a LED 3m GAIN 3d LED + PWR GAIN 3f + 3h Fig. 2: Opening the handheld transmitter Fig. 3: Bodypack transmitter 6.1.2. Selecting the Carrier Frequency dead within about 90 minutes. Replace the batteries with new ones as soon as possible. If the status LED fails to illuminate the batteries are dead. Insert new batteries. 6. Handheld transmitter: Slide the supplied adjustable protective ring onto the shaft and screw the battery compartment cover back on.
2. The red status LED on the transmitter lighting brightly means the transmitter is overloaded. Turn the GAIN control on the transmitter CCW to the point that the status LEDs will only flash occasionally. MIC Switch Both the handheld and bodypack transmitters provide a MIC switch. In order to mute the microphone, set the MIC switch to ”0”. Power and carrier frequency remain ON, however.
WLS 8060 ”MAX” 8. Specifications WLS 8060 Amplifier power (rms/peak) Drivers Speaker type Crossover frequency Sensitivity at 1W/1m Max.
Notizen * Notes 18
WLS 8060 ”MAX” Notizen * Notes 19
Mikrofone · Kopfhörer · Drahtlosmikrofone · Drahtloskopfhörer · Kopfsprechgarnituren · Akustische Komponenten Microphones · Headphones · Wireless Microphones · Wireless Headphones · Headsets · Electroacoustical Components Technische Änderungen vorbehalten. Specifications subject to change without notice. AKG Acoustics GmbH Lemböckgasse 21–25, P.O.B. 158, A-1230 Vienna/AUSTRIA Tel: (43 1) 86 654-0*, Fax: (43 1) 86 654-516 Internet: http://www.akg-acoustics.