AVR 330 Audio/VideoReceiver OWNER’S MANUAL DIGITAL EX LOGIC 7 PRO LOGIC 3 STEREO DSP SBL 7 CH. STEREO SURR.
Table of Contents 3 4 4 5 7 9 12 13 13 13 14 16 17 17 18 18 18 18 19 19 22 23 23 24 24 24 25 27 27 29 29 29 30 30 31 31 31 31 31 32 32 32 32 33 33 33 34 35 35 35 35 36 36 36 36 37 37 38 38 38 38 39 39 39 39 Introduction Safety Information Unpacking Front Panel Controls Rear Panel Connections Main Remote Control Functions Zone II Remote Control Functions Installation and Connections Audio Connections Video Connections SCART A/V Connections System and Power Connections Speaker Selection Speaker Placement Sys
Introduction Thank you for choosing Harman Kardon! With the purchase of a Harman Kardon AVR 330 you are about to begin many years of listening enjoyment. Designed to provide all the excitement and detail of movie soundtracks and every nuance of musical selections, the AVR 330 is truly a multichannel receiver for the new millennium. In addition to the traditional 5.
Safety Information Important Safety Information Verify Line Voltage Before Use Your AVR has been designed for use with 220240-Volt AC current. Connection to a line voltage other than that for which it is intended can create a safety and fire hazard and may damage the unit. If you have any questions about the voltage requirements for your specific model, or about the line voltage in your area, contact your dealer before plugging the unit into a wall outlet.
Front Panel Controls ( ¯ ˜ DIGITAL EX Û $ LOGIC 7 PRO LOGIC 3 STEREO DSP SBL 7 CH. STEREO SBR VID 1 DVD VID 2 CD VID 3 FM VID 4 TAPE 8 3 2 4 ! 7 ) 5 6 ı Ù Ú 8 CH SURR.
Front Panel Controls 7 Selector Buttons: When you are establishing the AVR’s configuration settings, use these buttons to select from the choices available, as shown in the Main Information Display ˜. 8 Tone Mode: Pressing this button enables or disables the Balance, Bass and Treble tone controls. When the button is pressed so that the words TONE I N appear in the Main Information Display ˜, the settings of the Bass and Treble Ú controls and of the Balance control Ò will affect the output signals.
Rear Panel Connections AM Antenna FM Antenna Tape Inputs Tape Outputs Subwoofer Output DVD Audio Inputs CD Inputs Multiroom Outputs Fan Vents 8-Channel Direct Inputs Digital Audio Outputs Video Monitor Outputs DVD Video Inputs NOTE: To assist in making the correct connections for multichannel input/output and speaker connections, all connection jacks and terminals have been color coded in conformance with the latest CEA standards as follows: Front Left: White Fr
Rear Panel Connections Video Monitor Outputs: Connect this jack to the composite and/or S-Video input of a TV monitor or video projector to view the on-screen menus and the output of any standard Video or S-Video source selected by the receiver’s video switcher. DVD Video Inputs: Connect these jacks to the composite or S-Video output jacks on a DVD player or other video source. Front Speaker Outputs: Connect these outputs to the matching + or – terminals on your left and right speakers.
Main Remote Control Functions 0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q ! " # $ % & ' ( ) * + , - Power Off Button IR Transmitter Window Program/SPL Indicator Power On Button Input Selectors AVR Selector AM/FM Tuner Select 6-Channel/8-Channel Direct Input Test Button Sleep Button Surround Mode Selector Night Mode Channel Select Button ⁄ / ¤ Buttons ‹ Button Set Button Digital Select Numeric Keys Tuner Mode Direct Button Tuning Up/Down OSD Button Dolby Mode Select Button DTS Digital Mode S
Main Remote Control Functions IMPORTANT NOTE: The AVR 330’s remote may be programmed to control up to seven devices, including the AVR. Before using the remote, it is important to remember to press the Input Selector button 4 that corresponds to the unit you wish to operate. In addition, the AVR’s remote is shipped from the factory to operate the AVR and most Harman Kardon CD or DVD players and cassette decks.
Main Remote Control Functions M Dolby Mode Selector: This button is used to select one of the available Dolby Surround processing modes. Each press of this button will select one of the Dolby Pro Logic II modes, Dolby 3 Stereo or Dolby Digital. Note that the Dolby Digital mode is only available with a digital input selected and the other modes only as long as a Dolby Digital source is not playing (except Pro Logic II with Dolby Digital 2.0 recordings, see page 32).
Zone II Remote Control Functions POWER A MUTE K OFF AVR VID1 VID2 AM//FM VID3 VID4 DVD CD TAPE DN TUNING UP DN PRESET UP The Zone II remote may be used in either the same room where the AVR is located, or it may be used in a separate room with an optional infrared sensor that is connected to the AVR’s Multi IR input jack . B C D E F G å Power Off: When used in the room where the AVR is located, press this button to place the unit in Standby.
Installation and Connections After unpacking the unit, and placing it on a solid surface capable of supporting its weight, you will need to make the connections to your audio and video equipment. Audio Equipment Connections We recommend that you use high-quality interconnect cables when making connections to source equipment and recorders to preserve the integrity of the signals.
Installation and Connections 7. If another component video device is available, connect it to the Video 2 Component Video Input jacks . The audio connections for this device should be made to either the Video 2 Input jacks # or any of the Coaxial or Optical Digital Input jacks !. 8. If the component video inputs are used, connect the Component Video Output to the component video inputs of your TV, projector or display device. 9.
Installation and Connections Black Black Figure 1: SCART/Cinch-Adapter for playback; signal flow: SCART → Cinch Yellow Yellow Red Red Black Black Red Red Blue 1 Blue Yellow Yellow Figure 2: SCART/Cinch-Adapter for record and playback; signal flow: SCART ↔ Cinch Green 1 Green White White Black Black Figure 3: Cinch/SCART-Adapter for playback; signal flow: Cinch → SCART Yellow Yellow Red Red Rot Red Figure 4: SCART/S-Video Adapter for playback; signal flow: SCART → Cinch Schwarz Black S-Video InIn S
Installation and Connections System and Power Connections The AVR 330 is designed for flexible use with multiroom systems, external control components and power amplifiers. Main Room Remote Control Extension If the receiver is placed behind a solid or smoked glass cabinet door, the obstruction may prevent the remote sensor from receiving commands. In this event, the remote sensor of any Harman Kardon or other compatible device, not covered by the door, or an optional remote sensor may be used.
Installation and Connections No matter which type or brand of speakers is used, the same model or brand of speaker should be used for the front-left, center and front-right speakers. This creates a seamless front soundstage and eliminates the possibility of distracting sonic disturbances that occur when a sound moves across mismatched front-channel speakers. Speaker Placement The placement of speakers in a multichannel home-theater system can have a noticeable impact on the quality of sound reproduced.
System Configuration Once the speakers have been placed in the room and connected, the remaining steps are to program the system configuration memories. With the AVR two kind of memories are used, those associated individually with the input selected, e.g. surround modes, and others working globally for all inputs selected like speaker output levels, crossover frequencies or delay times used by the surround sound processor.
System Configuration To make this process as quick and as easy as possible, we suggest that you use the full-OSD system with the on-screen menus, and step through each input. Input Setup The first step in configuring the AVR is to select an input, i.e. to associate an analog or digital input with each input source in use, e.g. CD or DVD.
System Configuration If you wish to customize the speaker size individually to each input, make certain that the cursor is on the BASS MGR line and press the ‹/ › Buttons E& so that INDEPENDENT appears in highlighted video. When this setting is entered all speaker size settings will be shown with their factory default size in the menu and all other inputs will turn to INDEPENDENT too. Now you should enter the speaker size settings prefered for the input selected, as described below.
System Configuration If the front left/right speakers are set to LARGE, three options are available: • If no subwoofer is connected to the AVR, press the ‹/ › Buttons E& on the remote so that NONE appears in the on-screen menu. When this option is selected, all bass information will be routed to the front left/right “main” speakers.
System Configuration As an example, in the Figure below, all speakers are set for “large,” and a subwoofer is set. When the SURR BACK line of the SPEAKER SETUP menu (Figure 4) is set to SMALL or LARGE the AVR 330 will be configured for 6.1/7.1-channel operation, and additional modes such as Dolby Digital EX and 7 STEREO or Logic 7 7.1 will appear, as they are only available when seven main speakers are present.
System Configuration field presentations. The choices available are Hall 1, Hall 2, Theater, VMAx Near and VMAx Far. The Hall and Theater modes are designed for multichannel installations, while the two VMAx modes are optimized for use in delivering a full surround field when only the front left and front right speakers are installed. See pages 27 for a complete explanation of the DSP surround modes. Note that the Hall and Theater modes are not available when a Dolby Digital or DTS soundtrack is played.
System Configuration Now the › cursor will be at the SURROUND line so that the delay for the surround speakers may be set. Press the ‹ / › Buttons E& until the distance from the video display at the front of the room to the surround speakers is entered. Finally, if the system is configured for 7.
System Configuration configuration button has been pressed the test noise will be heard from the front left speaker. 6. At this point, EzSet will take over, adjusting the output level of each channel so that when the process is complete all levels will be equal and at the set reference point. This process may take a few minutes, depending on the extent of adjustment required. 7.
System Configuration You may also adjust the output levels manually while using the level indication feature of the EzSet remote. To activate the sensor and indicator, simply press and release the SPL Indicator Select Button * on the remote while the test tone is circulating and set the main Volume Control ) to -15dB (respectively higher or lower, if needed, as outlined above). The Program/SPL Indicator 2 will change color to indicate the level.
Operation Surround Mode Chart MODE FEATURES DELAY TIME RANGE DOLBY DIGITAL Available only with digital input sources encoded with Dolby Digital data. It provides up to five separate main audio channels and a special dedicated Low Frequency Effects channel. Center: 0 - 30ft / 9m Initial Setting: 12ft / 3.6m Surround: 0 - 30ft / 9m Initial Setting: 10ft / 3m DOLBY DIGITAL EX Available when the receiver is configured for 6.1/7.1 channel operation, Dolby Digital EX is the latest version of Dolby Digital.
Operation Surround Mode Chart MODE FEATURES DELAY TIME RANGE DOLBY 3 STEREO Uses the information contained in a surround-encoded or two-channel stereo program to create center-channel information. In addition, the information that is normally sent to the rear-channel surround speakers is carefully mixed in with the front-left and front-right channels for increased realism. Use this mode when you have a center-channel speaker but no surround speakers.
Operation Basic Operation Once you have completed the setup and configuration of the AVR, it is simple to operate and enjoy. The following instructions should be followed for you to maximize your enjoyment of your new receiver: Turning the AVR On or Off • When using the AVR for the first time, you must press the Main Power Switch 1 on the front panel to turn the unit on. This places the unit in a Standby mode, as indicated by the amber color of the Power Indicator 3.
Operation Controls and Use of Headphones Surround Mode Selection • Adjust the volume to a comfortable level using the front panel Volume Control ı or remote Volume Up/Down )î buttons. One of the most important features of the AVR 330 is its ability to reproduce a full multichannel surround sound field from digital sources, analog matrix surround encoded programs and standard stereo or even mono programs. In all, a total of 23 listening modes are available on the AVR.
Operation To listen to a program in traditional two-channel stereo, using the front left and front right speakers only (plus the subwoofer, if installed and configured), press the Stereo Button 5 until SURR O F F appears in the Main Information Display ˜. Digital Audio Playback Digital audio is a major advancement over older analog surround processing systems such as Dolby Pro Logic.
Operation Digital Bitstream Indicators When a digital source is playing, the AVR senses the type of bitstream data that is present. Using this information, the correct surround mode will automatically be selected. For example, DTS bitstreams will cause the unit to switch to DTS decoding, and Dolby Digital bitstreams will enable Dolby Digital decoding.
Operation sense changes to the bitstream and channel count and reflect them in these indicators. Important Note: When a digital surround source (Dolby Digital, DTS) is played, the letters SBL/SBR for the Surround Back channels will appear only when a DTS ES DISCRETE 6.1 source is played. Then this surround mode will be indicated in the front display and on-screen display.
Operation Repeat the procedure as needed until all channels requiring adjustment have been set. When all adjustments have been made and no further adjustments are made for five seconds, the AVR will return to normal operation. level for each channel and surround mode as you prefer, e.g. you may lower the center channel level when you find it to be too high or increase the level of the rears when you find it to be too low with specific surround modes.
Advanced Features The AVR 330 is equipped with a number of advanced features that add extra flexibility to the unit’s operation. While it is not necessary to use these features to operate the unit, they provide additional options that you may wish to use. Surround Amplifier Channel Assignment The AVR is equipped with seven full-power amplifier channels to allow for complete 7.1-channel operation without the need for additional external amplifiers.
Advanced Features / Multiroom Operation Semi-OSD Settings Full-OSD Time Out Adjustment Multiroom Operation The semi-OSD system places one line messages at the lower third of the video display screen whenever the Volume, Input Source, Surround mode or tuner frequency of any of the configuration settings are changed. The semi-OSD system is helpful in that enables you to have feedback on any control changes or remote commands using the video display when it is difficult to view the front-panel displays.
Multiroom Operation Multiroom Setup Once the audio and IR link connections have been made, the AVR needs to be configured for multiroom operation using the steps below. Press the OSD button L to bring the M A ST E R M E N U (Figure 1) to the screen. Press the ⁄ button D twice, until the on-screen › cursor is next to the MULTI-ROOM line. Press the Set button F to enter the MULTI-ROOM menu (Figure 12).
Tuner Operation Basic Tuner Operation The AVR 330’s tuner is capable of tuning AM, FM and FM Stereo broadcast stations and receiving RDS data. Stations may be tuned manually, or they may be stored as favorite station presets and recalled from a 30 position memory. Station Selection 1. Press the AM/FM Tuner Select button 6 on the remote to select the tuner as an input.
Tuner Operation RDS Operation The AVR 330 is equipped with RDS (Radio Data System), which brings a wide range of information to FM radio. Now in use in many countries, RDS is a system for transmitting station call signs or network information, a description of station program type, text messages about the station or specifics of a musical selection, and the correct time.
Programming the Remote The AVR 330 is equipped with a powerful remote control that will control not only the receiver’s functions, but also most popular brands of audio and video equipment, including CD players, TV sets, cable boxes, VCRs, satellite receivers and other home-theater equipment. Once the AVR’s remote is programmed with the codes for the products you own, it is possible to eliminate most other remotes and replace them with the convenience of a single universal remote control.
Programming the Remote Code Readout Macro Programming When the code has been entered using the Auto Search method, it is always a good idea to find out the exact code so that it may be easily reentered if necessary. You may also read the codes to verify which device has been programmed to a specific Control Selector button. Macros enable you to easily repeat frequently used combinations of commands with the press of a single button on the AVR’s remote control.
Programming the Remote Programmed Device Functions Once the AVR’s remote has been programmed for the codes of other devices, press the appropriate Input Selector 4 to change the remote from control over the AVR to the additional product. When you press any of these buttons, it will briefly flash in red to indicate that you have changed the device being controlled. When operating a device other than the AVR, the controls may not correspond exactly to the function printed on the remote or button.
Programming the Remote Transport Control Punch-Through The AVR’s remote may be programmed to operate so that the Transport Control Functions P (Play, Stop, Fast Forward, Rewind, Pause and Record) for a VCR, DVD or CD will operate in conjunction with one of the other devices controlled by the remote. For example, while using and controlling the TV, you may wish to start or stop your VCR or DVD without having to change the device selected by the AVR or the remote.
Function List 44 FUNCTION LIST No. Button Name AVR Function DVD CD/CDR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Power On Power Off Mute AVR DVD CD Tape VID 1 VID 2 VID 3 VID 4 DIM AM/FM 6/8 Ch.
Function List No. Button Name Tape VCR (VID 1) TV (VID 2) CBL (VID 3) SAT(VID 3) 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 Power On Power Off Mute AVR DVD CD Tape VID 1 VID 2 VID 3 VID 4 DIM AM/FM 6/8 Ch.
Troubleshooting Guide SYMPTOM CAUSE SOLUTION Unit does not function when Main Power Switch 1 is pushed • No AC Power • Make certain AC power cord is plugged into a live outlet • Check to see if outlet is switch controlled Display lights, but no sound or picture • Intermittent input connections • Make certain that all input and speaker connections are secure • Press Mute button , • Turn up volume control • Mute is on • Volume control is down Units turns on, but Front-Panel Display does not light •
Technical Specifications Audio Section Stereo Mode Continuous Average Power (FTC) 65 Watts per channel, 20Hz–20kHz, @ < 0.07% THD, both channels driven into 8 ohms 5/7 Channel Surround Modes Power Per Individual Channel Front L&R channels: 50 Watts per channel, @ < 0.07% THD, 20Hz–20kHz into 8 ohms Center channel: 50 Watts, @ < 0.07% THD, 20Hz–20kHz into 8 ohms Surround (L & R Side, L & R Back) channels: 50 Watts per channel, @ < 0.
250 Crossways Park Drive, Woodbury, New York 11797 www.harmankardon.com Harman Consumer International: 2, route de Tours, 72500 Château-du-Loir, France © 2003 Harman Kardon, Incorporated Part No.
