Operation Manual

5
OPERATIONS
cdj 907
english
cdj 907
-.Switch de CD Player on via the Power Switch.
When the devices is on and the tray has no disc, “No Disc” appears -.Scanning: To do this rotate Shuttle wheel(11) forward or reverse.
on the display. You will scan or reverse at 4 different speeds depending on how
much you rotate the wheel.
Press OUT/EXIT BUTTON (15) to set desired ending point of the
SEAMLESS LOOP. You will know you are in SEAMLESS LOOP
mode because IN REAL TIME and OUT/EXIT LEDs will light and
flash. LOOP INDICATOR (8) in LCD DISPLAY will also flash.
Sound will continue with no interruption (SEAMLESS LOOP).
To exit SEAMLESS LOOP, press OUT/EXIT BUTTON (15). LEDs
will stay on but not flash. Music will resume normal play.
To replay loop, press the RELOOP BUTTON (17). IN REAL TIME
and OUT/EXIT LEDs and LOOP INDICATOR (8) in LCD
DISPLAY will all begin flashing again
(Must be in SEAMLESS LOOP mode). If a
SEAMLESS LOOP has not been created, follow instructions on this
page for creating a SEAMLESS LOOP. If a SEAMLESS LOOP has
already been created, press RELOOP BUTTON (17) to reenter the
SEMALESS LOOP mode.
Next, press OUT/EXIT BUTTON (15) to return to normal play
(figure 6). This disengages the SEAMLESS LOOP mode.
Press OUT/EXIT BUTTON (15) again for new desired ending point
of the loop.
FOR SHORTER LOOP: press OUT/EXIT BUTTON (15) quickly.
FOR LONGER LOOP: Wait until the song plays several frames, then
press OUT/EXIT BUTTON (15).
NOTE: YOU CAN ONLY EDIT THE ENDING PART OF THE
LOOP
The CD player automatically shuts off the transport
"Cueing" is the action of preparing for playback; when the and laser after 15 minutes (when in pause or cue mode). This will
Cue button(16) is pressed, playback return to the cue point and enters lengthen the life of your motor drive and laser. To restart player, just
pause mode. When the PLAY/PAUSE button(18) is pressed during press cue(16) or play(18) buttons
the cue mode, playback starts.
During normal play, each time you press TIME
Cue point setting: button(2), the display changes as following information.
Playback starts from pause ( using the jog wheel to set the starting a.Elapsed playing time
point ) or skip to a new track during play or pause. b.Remaining time in a selection
a.The beginning play point will be set to the cue point,or c.Total remaining time of the disc
b.Press the IN REALTIME CUE button(13) during playback to set
the new cue point,or
c.Memorize any of 10 CUE points by pressing MEMORY(1) to set
desired Cue then press any of 10 number buttons(6).
To return to Cue point press Cue Button(16). This will return to point
A or B above.The player has completed the cue or pause operation
and is waiting for the play start command.When the PLAY/PAUSE
button(18) is pressed, playback starts.
d.To recall cues, if the recall LED is lit you can press the last number
button cue stored and create a STUTTER EFFECT (see also p8). The
last cue that was stored or recalled will flash in the LED screen to let The speed increases or decreases respectively
you know it was last cued up while the PITCH BEND+(7) or PITCH BEND-(7) button is pressed.
The extent to which the speed changes is proportionated to the
-.Auto Cue: When disk is loaded, the cue point is set to the first amount of time the button is pressed. For example, if the PITCH
source of music. BEND+ button is held in continuously, the speed increases
If track is changed before pressing play, the cue point is changed to continuously.
the new starting point. The pitch changes within a range of +/- 16%. The jog wheel will
If you pause during playback this also sets the new cue point. temporarily bend the pitch of the music if the song is already playing
by rotating the wheel clockwise to speed up or counterclockwise to
-.Frame search: This is done by first pausing then using the jog slow down. The speed that you rotate the JOG Wheel determines the
wheel(12) to set the starting point.(When you use the jog wheel the percent of pitch bend.
monitor function allows you to hear what is playing. Once you have
set starting point press PLAY(18) then CUE(16) to again mute
output.)
-.Disc Tray.This operation only works when the power is on.Press
the OPEN/CLOSE button(10) to open or close the disc tray. -.Loop Play: You can create a seamless loop between two points
Press PLAY button tray automatically closes. If tray is not closed continuously.
after 60 seconds it will close automatically and pause. Press PLAY/PAUSE BUTTON (18) so a CD is playing. The
The disc trays cannot be opened during playback to prevent playback PLAY/PAUSE BUTTON'S LED lights.
from being interrupted if the OPEN/CLOSE button is pressed Press IN REAL TIME CUE BUTTON (13). This sets the starting
accidentally. Stop playback, then press the OPEN/CLOSE point of the SEAMLESS LOOP. The IN REAL TIME CUE'S
button(10). BUTTON LED will light
CAUTION:Do not play foreign objects in the disc tray, and do not
place more than one disc in the disc tray at a time. Doing so may
result in malfunction.
Do not push the disc tray in manually when the power is off, as this
may result in malfunction and damage the player.
-.Selecting Tracks:Select desired track using NUMBER Button(6)
or press the TRACK Buttons once to move to one higher or lower
track or Hold the TRACK buttons(14) in to change tracks
continuously at a higher speed.
When a new track is selected during playback, playback begins as
soon as the search operation is completed. -.Samless Loop:
-.Starting Playback: Press the PLAY/PAUSE button(18) during the
pause or cue to start playback. The PLAY indicator lights when
playback starts
-.Stoping Playback: There are two ways to stop playback.
a.Press the PLAY/PAUSE button(18) during playback to pause at
that point.
b.Press the CUE button(16) during playback to return to the position
at which playback started(Back Cue).
-.Pausing: Press the PLAY/PAUSE button(18) to switch between
play and pause.
The PAUSE indicator lights when the pause mode is set.
-Sleep Mode.
-.Cue:
-Time Display:
-.Pitch Bending: