Operation Manual
6
When you have finished using the CD player, before switching off the CAUTION:
power, be sure that the disc holder had been closed with the Do not forcibly close the disc holder when the power is off.
OPEN/CLOSE button.
POWER OFF
POWER OFF
Do not switch off the power when the disc holder is open. Switch off the power after the disc holder has been closed with the
OPEN/CLOSE button.
BEFORE SWITCHING OFF THE POWER
1. Precautions on handling compact discs. implement such as a pencil or ball point pen.
- Do not allow fingerprints, oil or dust to get on the surface of the - Condensation will form if a disc is brought into a warm area from
disc. a colder one, such as outdoors in winter. Do not attempt to dry the
- If the disc is dirty, wipe it off with a soft dry cloth. disc with a hair dryer, etc..
- Do not use benzene, thinner, water, record spray, electrostatic- 2. Precaution on storage
proof chemicals, or silicone-treated cloths to clean discs. - After playing a disc, always unload it from the player.
- Always handle discs carefully to prevent damaging the surface; - Always store the disc in the jewel case to protect from dirt or
in particular when removing a disc from its case or returning it. damage.
- Do not bend the disc. - Do not place discs in the following areas:
- Do not apply heat. - Areas exposed to directs sunlight for a considerable time.
- Do not enlarge the hole in the center of the disc. - Areas subject to accumulation of dust or high humidity.
- Do not write on the label (printed side) with a hard-tipped - Areas are affected by heat from indoor heaters, etc..
HANDLING COMPACT DISCS
OPERATIONS
english
cdj 907
-.Program Play:
-.Memory Cuening: 2.
-.Fader Start Playback:
-.
-.Relay Play using two Players:
-.End of Operation: Before you switch off the CDPlayer , please make
sure that the CDTray is completely closed before you switch off.
If theis is not the case, switch the CDPlayer on again and close trhe
CDTray with the Open/Close button.
Press PROG Button(8) to make the unit enter the continuous program of whatever tracks you wish
program mode and stop condition. The PROGRAM indicator lights. *By setting a cue point on the standby player, you can perform relay to
Select Track using NUMBER button(6) or TRACK SEARCH button(14) any desired cue point on the selected track
press PROG. again. Repeat this up to 30 times.
Press PLAY button(18) to begin playing programmed tracks. To cancel NOTE: Relay play may not work properly if the audio out jacks on the
Program press and hold PROG. Button(8) more than 2 sec two players are not connected to the same audio amplifier
Press the MEMORY button(1) to make the unit or press the RELAY button(21) on the front panel of Controller
enter cue memory mode, then press the desired numerical button(6) at the
desired cue point to memorize. The numeral(4) on the display will flash *The default has no Relay function when power on
twice then lit steadily to indicate the cue memory has been set. *Pressing the RELAY button to enable Relay function
Press the RECALL button(5) to make the unit enter cue recall mode, then *While the Relay is enabled, the LED will light on
press the desired numerical button(6) to recall the desired cue memory *In the single mode, the CD player will be paused at the next track when
point. A new cue point will be set. finish playing current track
To clear all the cue memory, just press and hold the MEMORY button(1) *And only the other side of CD player that is standby in pause mode will
for more than 2 seconds. All the cue memory will be clear start playing automatically
*There is no Fader start function when in the Relay mode
Both player's CONTROL jack are connected to
Mixer's CROSS FADER signal output CH1 or CH2; when the jack are Stutter Effect: It can create a sound similar to a CD skipping. The
connected, the operation for both player as following: STUTTER Effect can be created in 2 ways.
Left player will return to standby mode at CUE point automatically when
move CROSS FADER from left to right to start playback on right player. 1.By rapidly pressing the CUE BUTTON (16)
Right player will return to standby mode at CUE point automatically a.Press PLAY/PAUSE BUTTON (18) so that music is playing.
when move CROSS FADER from right to left to start playback on left PLAY/PAUSE LED will light
player b.Next, rapidly press the CUE BUTTON (16) in sync with the music
How to set the Relay function 2.By Hitting The DIRECT TRACK ACESS BUTTONS (6)
a.Press PLAY/PAUSE BUTTON (18) so that music is playing.
1.By either the both player's CONTROL jack are connected to each other PLAY/PAUSE LED will light
without pressing the RELAY button; when the both player's CONTROL b.Press MEMORY BUTTON (2) to set a CUE POINT in memory.
jack are connected to each other, the relay-play effects can be produced. MEMORY LED will light
The relay play is explained as below c. Press desired DIRECT TRACK ACCESS BUTTON
d.Press RECALL BUTTON (5)
*Set both players to single play mode (the SINGLE indicators(6) will lit e.Once RECALL LED lights, rapidly press the DIRECT TRACK
in the displays). ACCESS BUTTON (6) previously selected
*Begin playback on the first player
*When the currently playing track ends, playback will begin
automatically on the standby player
*The first player will enter standby mode at the beginning of the next
track on its disc
*By repeating this operation, the two players can be used to perform
continuous relay play
*By loading new discs on the standby player, you can construct a