Operation Manual

27- Contrapeso.
Su ajuste proporciona la fuerza descendente
adecuada para el trabajo de la aguja sobre
el disco.
27- Counterweight.
Adjustment creates the proper downward
pressure of the stylus to the record. Attach
now by sliding the counterweight onto the
rear of the tone arm. Twist lightly and it
will screw on to the rear shaft of the tone
arm.
- Turn the power dial to turn on and the
speed indicator and the strobe iluminator
will light up.
- Insert the target light for
the stylus.
illuminating
- Place a record on the turntable mat.When
playing a 45rpm record with a large center
hole, place the 45rpm adapter on the center
spindle.
- Set the rotation speed (33/45/78) to match
the record.
- Relase the arm clamp.
- Set the cueing lever to the up position.
- Press the Start/Stop button and the
turntable platter will start to rotate.
- Move the tone arm over the desired groove.
- Set the Cuening lever to the down
position, the tone arm will descend slowly
onto. The record and play begins.
- Set the desired Pitch adjusts range by
depressing the buttons until the desired
pitch is reached. Options are +/-10%,or +/-
20%, or +/-50%.
- Adjust the Pitch to a desirable speed.
During play, observe
the strobe dots. If the strobe dots appear
to the right, the Pitch is slower that the
rater speed . If they flow to the left, the
rated speed.
If the strobe dots appear stationary, witch
means the platter is in normal turntable
speed, move the pitch control slider up or
down to adjust the speed
When pitch is on 0%,
is slower.
- To suspend play, lift tone arm with
cuening lever.
- When play is finished, raise the cueing
lever, move the tone arm to the armrest and
secure the tone arm with the arm clamp.
- Press the Start/Stop button to Stop the
platter rotating.
- Turn the power dial to turn off the power.
- Accione el boton de puesta en marcha. El
indicador de velocidad y la luz del
estroboscopio se encenderan.
- Active la luz retractil para la
iluminacion de la aguja pulsando el control
adyacente.
- Ponga un disco en la alfombrilla, en caso
se ser un disco de 45 rpm debe situar el
adaptador encajandolo en el teton central.
- Escoja la velocidad (33/45/78) adecuada
al disco que va a reproducir.
- Retire el protector de la aguja y libere
el brazo.
- Disponga la palanca Elevacion / Descenso
tal que el brazo este elevado.
- Presione el boton Start / Stop y el plato
empezara a girar.
- Situe el brazo encima de la pista que
desea empezar a reproducir.
- Disponga la palanca Elevacion / Descenso
tal que el brazo descienda hasta posar la
aguja sobre la pista del disco deseada. En
este momento comenzara la reproduccion.
- Seleccione el rango de velocidad (Pitch)
deseado +/-10% o +/-20% o +/-50%
presionando los botones hasta alcanzar la
velocidad deseada.
- Ajuste el control de velocidad Pitch a la
velocidad deseada. Durante la reproduccion
observe los puntos del estroboscopio, si
estos se desplazan hacia delante la
velocidad es menor que el valor fijado
(33/45/78), si se desplazan hacia atras la
velocidad es mayor. Cuando los puntos del
estroboscopio aparecen estacionarios la
velocidad es exactamente la seleccionada,
es decir 33,45 78 rpm.
- Cuando quiera terminar la reproduccion
situe el brazo en posicion levantando
mediante la palanca Elevacion / Descenso y
fijelo en su posicion de reposo.
- Accione el boton Start / Stop para que el
plato deje de girar y presione el boton de
encendido para desconectar el aparato.
Operating Funcionamiento
Tone arm BrazoTone arm Brazo
19- Headshell
Install cartridge here. When installing a
cartridge, refer to the installation
instructions supplied by the manufacturer
of that cartridge. During installation,
attach the stylus protector to guard the
stylus tip from damage.Attach wires as
follows:
White (L+) Left Channel +
Blue (L-) Left Channel -
Red (R+) Right Channel +
Green (R-) Right Channel -
19- Portacapsula
Instale la capsula aqui. Al instalarla siga
las instrucciones proporcionadas por el
fabricante de esta. Durante la instalacion
no quite el protector de la aguja para
evitar desperfectos de la misma. Conecte
los cables al terminal de la capsula, la
mayoria de los cables estan codificados por
colores. Conecte cada cable al terminal del
mismo color.
Blanco (L+) Canal Izquierdo +
Azul (L-) Canal Izquierdo -
Rojo (R+) Canal Derecho +
Verde (R-) Canal Derecho -
20- Headshell Locking Nut
Attach Headshell by inserting into the
front end of the tone arm, then turn the
locking nut cockwise with the headshell
firmly held horizontally.
20- Rosca de Bloqueo del Portacapsulas
Inserte el portacapsulas en el extremo del
brazo, gire la rosca en el sentido de las
agujas del reloj manteniendo el
portacapsulas firme en posicion horizontal.
21- S-Shaped Tone Arm
21- Brazo metalico tipo S
24- Tone Arm Clamp and Rest.
Use this rest for the tone arm and clamp it
in position during transportation.
24- Bloqueo del Brazo.
Utilicelo en caso de tener que mover o
transportar el equipo para evitar que el
brazo se dane.
22- Tone Arm Lift Adjust Screw.
Controls the Amount of lift.
22- Tornillo de Ajuste de Elevacion.
Ajusta el grado de elevacion del brazo por
encima el disco.
23- Tone Arm Lift.
This elevates tonearm above the record
surface.
the
23- Elevador del Brazo.
Permite elevar el brazo por encima de la
superficie del disco.
26- Anti-Skate Control.
This applies inward force to the tone arm so
it doesn’t skip outward across the record
due to the centrifugal force of the record
spinning. Cartridge manufacturers usually
specify the proper setting of this.
25- Palanca Elevacion / Descenso del Brazo.
Nos permite elevar y descender el brazo
respecto del disco.
25- Tone Arm Lever.
Controls the up and down action of the tone
arm lift.
26- Control Anti-Patinamiento (Anti-Skate)
Aplica una fuerza al brazo tal que lo hace
girar hacia el interior contrarrestando la
fuerza centrifuga propia del giro.De este
modo evitamos que el brazo se desplace hacia
fuera por encima del disco. Los fabricantes
de capsulas acostumbran a proporcionar el
valor anti-Skate adecuado para cada modelo.
2727
2323
2626
2525
2222
2424
2121
2020
1919