Technical Specifications

Data sheets are subject to change without notice. For the latest version, please check the product page at www.tccmaterials.com
Available Size
• 8.6 oz. (250 mL) tube (BOM #120438)
Coverage
Each 8.6 oz. tube yields approximately 30 lin. ft. (9.1 m) at
⅛ in. x ⅛ in. (3x3 mm) line
5. INSTALLATION
Preparation
Read all directions before starting work. Proper surface
preparation is crucial to achieving a successful application.
1. For better adhesion concrete surfaces should be dry and
cured a minimum of 21-28 days from date of placement
depending upon curing and drying conditions. Surface and
ambient temperature must be 40°F (5°C) or above.
2. Prepare all anchor holes prior to placement of Fast-Setting
Anchoring Epoxy. Drill the hole to the correct diameter and
depth to suit the anchor, using a rotary percussion drill and
carbide-tipped bit. Hole diameter is typically ⅛ in. (3 mm)
greater than the anchor diameter and hole depth is typically
nine times anchor diameter.
3. Surface to be bonded must be clean and sound. Remove
dust, dirt, grease, curing compounds laitance, and other
foreign matter by sandblasting, hydro blasting, or mechanical
abrasion. For drilled holes and cracks, clean with a nylon
bristle brush. Remove all water and dust with clean
compressed air prior to installation.
Note: It is the responsibility of the installer/applicator to ensure
the suitability of the product for its intended use.
Mixing
• Before using, condition material to 65°F-85°F (18°-29°C).
• Unscrew and remove both protective cap and plug from the
cartridge. Insert the flow restrictor, attach the static nozzle
mixer and tighten nut. Load cartridge into standard caulking
gun.
1. PRODUCT NAME
Akona
®
Fast-Setting Anchoring Epoxy
2. MANUFACTURER
Akona Manufacturing, LLC
A TCC Materials Company
2025 Centre Pointe Blvd., Suite 300
Mendota Heights, MN 55120 USA
Phone: [phone]
Web: tccmaterials.com
3. PRODUCT DESCRIPTION
Akona Fast-Setting Anchoring Epoxy is a two-component, non-
sag, 100% solids, high-performance, moisture tolerant epoxy
adhesive designed for anchoring bolts and rebar steel into
concrete and for bonding or repairing a variety of household
and common building materials including concrete, porous tile,
and stone. Because it is resistant to moisture during and after
curing, it is ideal for stopping air and water leaks. Gray in color.
Maximum width ⅛ in. (3 mm) annular, depth is limited by
diameter of anchor.
Features and Benefits
• High-strength
• Resists chemicals and solvents
• Moisture tolerant
• Fits standard caulking gun
• Non-shrink
• Fast-setting:
 Initial set time of in as little as 12-14 min.
 Initial cure time of 2 hr.
 Final cure of 12-16 hr.
• Non-sag
• Excellent adhesion
When/Where to Use
• Most household and building materials including concrete,
tile, stone
• For horizontal and vertical repairs
• Fills defects in concrete floors, walls, driveways, stairs, and
patios
• Bonds loose or cracked tiles
• Secures railings or posts
• Stops air and water leaks
• For setting anchor bolts, dowels, and rebar in concrete and
masonry
4. TECHNICAL DATA
FAST-SETTING
ANCHORING EPOXY
Fast-setting, 100% solids epoxy repair for general construction applications
Typical Values • Akona Fast-Setting Anchoring Epoxy
Mix ratio 1 part A; 1 part B by volume
Mixed color Gray
Solids (%) 100
Gel Time
2 oz. (60 g) mass: 14 minutes at
77°F (25°C)
Gel Time
1 oz. (30 g) mass: 30 minutes at
77°F (25°C)
Tensile strength
(ASTM D412)
4,500 psi (31 MPa)
Elongation (ASTM D412) 6%
Water absorption
(ASTM D-570)
0.37% at 7 days
Compressive strength
(ASTM D695)
11,000 psi
(75.8 MPa)
Rebar
Size
Hole
Diameter
Hole
Depth
Anchors per
8.45 fl. oz.
Tube
3/8” 7/16” 3⅜” 43
3/8” 7/16” 5⅝” 27
1/2” 9/16” 4½” 23
1/2” 9/16” 7½” 13
5/8” 3/4” 5⅝” 9
5/8” 3/4” 9⅜” 5
3/4” 7/8” 6¾” 6
3/4” 7/8” 11¼” 3
1” 1-⅛” 9” 3
1¼’ 1⅜” 11¼” 1