About This Manual Thank you for choosing Akuvox E16C door phone. This manual is intended for the administrators who need to properly configure the door phone. This manual applies to 116.30.1.134 version, and it provides all the configurations for the functions and features of E16C door phones. Please visit Akuvox forum or consult technical support for any new information or the latest firmwares.
Introduction of Icons and Symbols Warning: Always abide by this information in order to prevent the persons from injury. Caution: Always abide by this information in order to prevent the damages to the device. Note: Informative information and advice from the efficient use of the device. Tip: Useful information for the quick and efficient use of the device.
Related Documentation You are advised to refer to the related documents for more technical information via the link below: https://knowledge.akuvox.
Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Table of Contents 1. Product Overview ............................................................................................. 1 2. Change Log .......................................................................................................2 3. Introduction to Configuration Menu ............................................................... 3 4. Access the Device ............................................................................................ 4 4.1.
7.4.3.2. Configure Video Codec .................................................. 25 7.5. Configure DTMF Data Transmission ..................................................26 8. Relay Switch Setting ...................................................................................... 27 8.1. Relay Switch Setting ........................................................................... 27 8.2. Web Relay Setting ................................................................................28 8.2.1.
12.2. Live Stream ........................................................................................ 55 12.3. RTSP Stream Monitoring .................................................................. 56 12.3.1. RTSP Basic Setting .................................................................56 12.3.2. RTSP Stream Setting .............................................................. 57 12.4. ONVIF .................................................................................................
E16C Administrator Guide 1.Product Overview Akuvox E16C is an Android-based IP video door phone with a touch screen. It incorporates audio and video communications, access control, and video surveillance. Its finely-tuned Android OS, SmartPlus and AI-based communication technology allow featured customization to better suit your operation habit.
E16C Administrator Guide 2.Change Log The change log will be updated here along with the changes in new software version. AKUVOX SMART INTERCOM www.akuvox.
E16C Administrator Guide 3.Introduction to Configuration Menu Status: this sections gives you basic information such as product information, Network Information, and account information etc. Account: this section concerns SIP account, SIP server, proxy server, transport protocol type, outbound proximity server. Network: this section mainly deals with DHCP&Static IP setting, and device deployment etc. Intercom: this section covers Intercom call setting, call log etc.
E16C Administrator Guide 1. Discovery mode: It is a plug and play configuration mode. Akuvox devices will configure themselves automatically when users power on the devices and connect them to network. It is super time-saving mode and it will greatly bring users convenience by reducing manual operations. This mode requires no prior configurations previously by the administrator. 2. SmartPlus mode: Akuvox SmartPlus is an all-in-one management system.
E16C Administrator Guide E16C door phone system setting can be either accessed on the device directly or on the device web interface. 4.1. Access the Device Setting on the device If you want to access the device setting in order to configure and adjust the parameters, you can do it directly on the device. To access the device setting, you can long press where on the initial screen for approximately five seconds, then enter the default PIN code “admin” and press Confirm. 4.2.
E16C Administrator Guide Tip: You can also obtain the device IP address using the Akuvox IP scanner to log in the device web interface. Please refer to the URL below for the IP scanner application: http://wiki.akuvox.com/doku.php?id=tool:ip_scanner&s[]=ip&s[]= scanner Note: Google Chrome browser is strongly recommended. The Initial user name and password are “admin” and please be case-sensitive to the user names and passwords entered. 5.Time and Language Setting AKUVOX SMART INTERCOM www.akuvox.
E16C Administrator Guide 5.1. Language Setting When you first set up the device, you might need to set the language to your need. You can select the language display the device web Setting > Time/Lang > LCD Language interface. 5.2. Time Setting Time setting on the web Setting > Time/Lang > Time interface allows you to set up time and date manually while allowing you to use NTP server address that you obtained to automatically synchronize your time and date.
E16C Administrator Guide is used and then press Confirm tab for the confirmation. The default time zone is GMT+0.00. Primary Server: enter the primary NTP server you obtained in the NTP Server field. Secondary Server: enter the secondary NTP server you obtained in the NTP Server field to be used as a backup. Update Interval: set the automatic time update via NTP server. Note: When the check box is not ticked, the parameters related to NTP server will become unedited. 5.3. LED Setting 5.3.1.
E16C Administrator Guide Parameter set-up: Enabled: tick the check box if want to enable the card reader LED lighting and vice versa. Start Time - End Time (H): enter the time span for the LED lighting to be valid, e.g. if the time span is from 18-22 it means LED light will stay on during the time span from 6:00 pm to 10:00 pm during one day (24 hours). 5.3.2.
E16C Administrator Guide Note: IR LED light should be triggered first before the white light can be valid in the facial recognition, however IR LED light does not need to be triggered for the white light function in the QR code scan. 5.4. Screen Display configuration E16C door phones allow you to enjoy a variety of screen displays to enrich your visual and operational experience through the customized setting to your preference. 5.4.1.
E16C Administrator Guide 5.4.2.Upload Screensaver You can upload screensaver pictures separately or in batch to the device and to the device web interface for publicity purpose or for a greater visual experience. To configure the configuration on web Device > LCD > Upload ScreenSaver interface. You can upload a maximum of 5 pictures, and each picture will be displayed in rotation according to the ID order with specific time duration (Time Interval) you set. AKUVOX SMART INTERCOM www.akuvox.
E16C Administrator Guide 5.5. Volume & Tone Configuration Volume and tone configuration in E16C door phone refers to the Call volume, the AD volume, key volume and Mic volume and open door tone configuration. Moreover, you can upload the tone you like to enrich your personalized user experience. 5.5.1.Volume Configuration You can configure the Mic volume, speaker volume and temper alarm volume according to your need for the intercom-based audio&video communication.
E16C Administrator Guide 5.5.2.Upload Open Door Tone You can upload the Open-Door Tone on the device web interface.To configure the configuration on web Device > Voice > Open Door Tone Setting interface. 5.5.3. Configure Door Access Prompt Text You can enable or disable the door access prompt to be shown on the access control terminal screen for door open failure and success. To configure the configuration on web Setting > Door > Open Door Succeeded Text Prompt interface.
E16C Administrator Guide 6.Network Setting 6.1. Device Network Connection Setting You can configure the default DHCP mode (Dynamic Host Configuration Protocol) and static IP connection. Moreover, you can set up IP address, Subnet Mask, Default Gateway, LAN DNS1 & LAN DNS2. To configure the configuration on web Network > Ethernet > LAN Port interface. Parameter Set-up: DHCP: select the DHCP mode by checking off the DHCP box. DHCP mode is the default network connection.
E16C Administrator Guide environment. Default Gateway: set up the correct gateway default gateway according to the IP address of the default gateway. DNS1/DNS2: set up DNS1/ DNS2 (Domain Name Server)according to your actual network environment. DNS1 is the primary DNS server address while the DNS2 is the secondary server address and the door phone connects to DNS2 server when the primary DNS server is unavailable . 6.2.
E16C Administrator Guide Discovery Mode: go to “Enabled” to turn on the discovery mode of the device so that it can be discovered by other devices in the network,and go to “Disabled” if you want to conceal the device so as not to be discovered by other devices. Device Address: specify the device address by entering device location information from the left to the right :Community, Unit, Stair, Floor, Room in sequence.
E16C Administrator Guide 7.Intercom Call Configuration Intercom call in the device can be configured to allow you to perform a variety of customized intercom calls such as IP call and SIP call for different application scenarios. 7.1. IP call & IP Call Configuration IP call can be made directly on the intercom device by entering the IP number on the device. And you can also disable the direct IP call if you allow no IP call to be made on the device. 7.1.1.
E16C Administrator Guide Note: You can press Home to the initial screen. on the Dial screen if you want to go back 7.1.2.IP Call Configuration To configure the IP call on the device web Basic > Direct IP interface. Parameter Set-up: Direct IP Call: go to “Enable” or “Disable” to turn the direct IP call on or off. For example if you do not allow direct IP call to be made on the device, you can go to” Disable” to terminate the function.
E16C Administrator Guide 7.2.1.SIP Account Registration E16C door phones support two SIP accounts that can all be registered according to your applications. The SIP account can be configured on the device interface. To perform the SIP account setting on the web Account > Basic > SIP Account Interface. Parameter Set-up: Status: check to see if the SIP account is registered or not. Account Active: go to “Enable” or “Disable” to activate or deactivate the registered SIP account.
E16C Administrator Guide 7.2.2.SIP Server Configuration SIP servers can be set up for device in order to achieve call session through SIP server between intercom devices. To set up SIP server, you can go to Account > Basic > Preferred SIP Server. Parameter Set-up: Preferred SIP Server: enter the primary server IP address number or its URL. Alternate SIP Server: enter the backup SIP server IP address or its URL. Port: set up SIP server port for data transmission.
E16C Administrator Guide Parameter Set-up: Enable Outbound: go to “Enable” and “Disable” to turn on or turn off the outbound proxy server. Server IP: enter the SIP address of the outbound proxy server. Port: enter the Port number for establish call session via the outbound proxy server Backup Server IP: set up Backup Server IP for the back up outbound proxy server. Port: enter the Port number for establish call session via the backup outbound proxy server. 7.2.4.
E16C Administrator Guide UDP: select “UDP” for unreliable but very efficient transport layer protocol. UDP is the default transport protocol. TCP: select “TCP” for Reliable but less-efficient transport layer protocol. TLS: select “TLS” for Secured and Reliable transport layer protocol. DNS-SRV: select “DNS-SRV” to obtain DNS record for specifying the location of servers. And SRV not only records the server address but also the server port.
E16C Administrator Guide Auto Answer Mode: set up the “Video” or “ Audio mode” you preferred for the automatic call answering. 7.4. Call Settings 7.4.1.Maximum Call Duration Setting E16C door phone allows you to set up the call time duration in receiving the call from the calling device as the caller side might forget to hang up the phone. When the call time duration is reached, the door phone will terminate the call automatically.
E16C Administrator Guide Parameter set-up: Dial In Time: enter the dial in time duration for you door phone (ranging from 30-120 sec.) for example, if you set the dial in time duration is 60 second in your door phone, then the door phone will hang up the incoming call automatically if the call is not answered by the door phone in 60 seconds. 60 seconds is the dial in time duration by default. Dial Out Time: enter the dial in time duration for your door phone (ranging from 5-120 sec.
E16C Administrator Guide Please refers to the bandwidth consumption and sample rate for the four types of codecs below: Codec Type Bandwidth Sample Rate Consumption PCMA 64 kbit/s 8kHZ PCMU 64 kbit/s 8kHZ G729 8 kbit/s 8kHZ G722 64 kbit/s 16kHZ 7.4.3.2. Configure Video Codec This series support H.264 codec that provides a better video quality at much lower bit rate with different video quality and payload. To do the configuration, you can go to Account > Advanced > Video Codec.
E16C Administrator Guide Payload: select the payload type (ranging from 90-118) to configure the audio codec payload. The pay load between the door phone and the corresponding intercom device should be identical. The default payload is 104. 7.5.
E16C Administrator Guide 8.Relay Switch Setting 8.1. Relay Switch Setting You can configure the relay switch(es) and DTMF for the door access on the web Access Control > Relay > Relay interface. Parameter Set-up: Trigger Delay (Sec): set the relay trigger delay timing (Ranging from 1-10 Sec.) For example, if you set the delay time as “5” sec. then the relay will not triggered until 5 seconds after you press “unlock “ tab. Hold Delay (Sec): set the relay hold delay timing (Ranging from 1-10 Sec.
E16C Administrator Guide DTMP Mode is set as 3-digits. Relay Status: relay status is low by default which means normally closed(NC) If the relay status is high, then it is in Normally Open status(NO). Relay Name: name the relay switch according to your need. For example you can name the relay switch according to where the relay switch is located for the convenience.
E16C Administrator Guide Parameter Set-up: Type: select among three options Disabled, WebRelay and Both. Select WebRelay to enable the web relay. Select “Disable” to disable the web relay. Select Both to enable both local relay and web relay. IP Address: enter the we relay IP address provided by the web relay manufacturer. User Name: enter the User name provided by the web relay manufacturer. Password: enter the password provided by the web relay manufacturer.
E16C Administrator Guide performed on the intercom device, while this setting is optional. And please refer to the example below: http://admin:admin@192.168.1.2/state.xml?relayState=2. After the web relay is set up, you can configure the specific web relay to be triggered based on the relay location for the door access. To configure the configuration on web Access Control > User interface. 8.2.2.
E16C Administrator Guide 9. Door Access Schedule Management You are required to configure and make schedule for the user-based door access via RF card, Private PIN and Facial recognition. 9.1. Configure Door Access Schedule You can create door access schedules so that they can be later conveniently applied to the door access control intended for individual user or a group of users created. More over, you can edit your door access schedule if needed. 9.1.1.
E16C Administrator Guide To create a longer period schedule, select Schedule Type as Normal. 9.1.2.Import and Export Door Access Schedule In addition to creating door access schedule separately, you can also conveniently import or export the schedules in order to maximize your door access schedule management efficiency. To configure the configuration on web Access Control > Schedule Setting > Import/Export Schedule(.xml) interface. Note: It only supports .
E16C Administrator Guide 9.1.3.Edit the Door Access Schedule If you want to edit or delete your door access schedule you created, you can edit or delete the configured schedule separately or in batch on the web interface. To configure the configuration on web Access Control > Schedule Setting > Schedule Management interface.
E16C Administrator Guide 10. Door Unlock Configuration E16C door phone offer you three types of door access via PIN code, RF card and Facial recognition. You can configure them on the device and web interface. More over, you can import or exporting the configured files to maximize your RF card configuration efficiency. 10.1.Configure PIN Code for Door Unlock You can create and modify both public PIN code and private PIN code for the door access on E16C door phones. 10.1.1.
E16C Administrator Guide Note: Public PIN code will not valid until the function is turned on. Note: APT+PIN can only be applicable when the device is added to the Akuvox SmartPlus. 10.1.2. Configure Private PIN Code on the Device You can configure door access by Private PIN code on the device by entering the user’s name and the PIN code for the door access. To configure private PIN code , you can press User icon on the Setting screen. Press Add tab and enter the User name.
E16C Administrator Guide 10.1.3. Configure Private PIN Code on the Web Interface On the web Access Control > User interface, you can not only set up PIN code, but also set and select the door access schedule that you created for the validity of the PIN Code access during a certain time span you scheduled. In addition, you can set the limit for the total number of valid PIN code door access. Enter the user’s name and floor number then go to Private PIN section to enter the private PIN code in Code.
E16C Administrator Guide Parameter Set-up: Validity Term: select validity term among three options: Always, Schedule and Never. if you select Always, then the door access via PIN code will always be valid with no restriction. If you select Schedule, then you are required to select among the created schedule for user-based PIN code access. If you select Never then the PIN code access will never be valid. Frequency: set the total number of valid PIN code access allowed.
E16C Administrator Guide Parameter Set-up: Authorization Mode: select access mode between “ PIN” and “APT#+PIN”. if you select “PIN” then you are only required to enter PIN code directly for the door access,while if you select “ APT#+PIN”, then you are required to enter the Apartment Number first before entering your PIN code for the door access. 10.2.Configure RF Card for Door Unlock 10.2.1. Configure RF Card on the Web Interface To configure the configuration on web Access Control > User interface.
E16C Administrator Guide 10.2.1.1. Configure RF Card Code Format If you want to integrate with the third-party intercom system in terms of RF card door access, you can change the RF card code format to be identical with that applied in the third-party system. To configure the configuration on web Access Control > CardSetting interface. Parameter Set-up: IC-Card Display Mode: select the card format for the ID Card for the door access among five format options: 8H10D; 6H3D5D(W26); 6H8D; 8HN; 8HR.
E16C Administrator Guide 10.2.2.2. Configure Facial Recognition on Web Interface To configure the configuration on web Access Control > User interface. Parameter Set-up: Status: It will show “Registered” when the picture uploaded conforms to the format and standard otherwise it would show “ Unregistered” as the default. However, the status will be changed back to “Unregistered” if the picture uploaded is cleared when you press the Reset tab.
E16C Administrator Guide Note: Pictures to be uploaded should be in jpg or png format. 10.3. Configure Door Access Using Configured Files. E16C door phones allow you to speedily configure user(s)-specific door access in batch by importing the configured all-in-one door access control files incorporating user information, door access type, door access schedule etc.
E16C Administrator Guide 10.4.1. Unlock by QR Code QR code is another option for door access. If you want to apply QR code access, you need to enable the QR code function. To enable the QR code function , you can go to Access Control > Relay > Open Relay via QR Code. Note: The function should work with Akuvox SmartPlus. For more information, please contact Akuvox technical support. 10.4.2.
E16C Administrator Guide Parameter Set-up: Enabled: enable or disable the Bluetooth function. Bluetooth is turned off by default. Rssi Threshold: select the signal receiving strength from -85~-50db in absolute terms. The higher value it is, the greater strength it has. The default value is 72db in absolute terms. Open Door Interval: select the time interval between the every two Bluetooth door accesses. 10.4.3.
E16C Administrator Guide Parameter Set-up: Enable: enable the HTTP command unlock function by go toing on Enable field. User Name: enter the user name of the device web interface, for example “Admin”. Password: enter the password for the HTTP command. For example : “12345”. Please refer to the following example: http://192.168.35.
E16C Administrator Guide Parameter Set-up: Trigger Electrical Level: select the trigger electrical level options between “High” and “Low” according the actual operation on the exit button. Execute Relay: set up relays to be triggered by the input. Door Status: display the status of input signal. 10.4.5. Unlock by Reception Tab In the device home screen, E16C door phone provide residents and visitors a quick door access by pressing the Reception tab on the bottom of the home screen.
E16C Administrator Guide Number: enter the SIP/IP number to be called to after pressing the Reception icon for the door access. 10.4.6. Unlock by DTMF Code DTMF codes can be configured on the door phone web interface and set up identical DTMF code on the corresponding intercom devices such as indoor monitor, which allows residents to enter the DTMF code on the soft keypad or press DTMF code attached unlock tab on the screen to unlock the door for visitors etc., during a call.
E16C Administrator Guide “DTMF-Relay” “Telephone-Event” according to your need. DTMF Payload: select the payload 96-127 for data transmission identification. Note: Please refer to the chapter Configure DTMF Data Transmission for the specific DTMF code setting. Intercom devices involved must be consistent in the DTMF type otherwise DTMF code cannot be applied. 10.4.7.
E16C Administrator Guide Parameter set-up: Mode: select either Disabled Mode or Wrist Mode for temperature measurement according to your need. The device can be installed with digital forehead temperature detector therefore you can are required to set the mode properly according to your application. Mask Detection: select Enable or Disable to turn on or turn off the mask detection.
E16C Administrator Guide will appear for you to fill in SIP/IP numbers when you check the box in the Action to Execute field. 10.4.7.2. Ambient Temperature Configuration In order to offset the minor variations on the temperature as affected by the ambient temperature in the different places where the device is installed or in the different time of a day, you are required to configure the temperature setting on the basis of time segments during a day.
E16C Administrator Guide 11. Security 11.1.Tamper Alarm Setting Tamper alarm function serves as a protection against any unauthorized removal of the devices by triggering off the temper alarm on the device. To configure the configuration on web Security > Basic > Temper Alarm interface. Parameter Set-up: Enable: tick the check box to enable the temper alarm function. When the temper alarm goes off , you can press the Disarm tab beside the check box to clear the alarm.
E16C Administrator Guide 11.2.Security Notification Setting 11.2.1. Email Notification Setting If you want to receive the security notification via email, you can configure the Email notification on the web interface properly. To configure the configuration on web Setting > Action > Email Notification interface. Parameter Set-up: Sender’s Email Name: enter the name of the email sender. Sender's email address: enter the sender’s email address from which the email notification will be sent out.
E16C Administrator Guide Port: enter the port number from which the email is sent out. SMTP user name: enter the SMTP user name, which is usually the same with sender’s email address. SMTP password:configure the password of SMTP service, which is same with sender’s email address. Email subject: enter the subject of the email. Email content: compile the emails contents according to your need. 11.2.2.
E16C Administrator Guide 11.2.3. TFTP Notification Setting If you want to receive the security notification via TFTP, you can configure the FTP notification on the web interface properly. To configure the configuration on web Setting > Action > TFTP Notification interface. Parameter set-up: TFTP Server: enter the address (URL) of the TFTP server for the FTP notification 11.3.
E16C Administrator Guide 12. Monitor and Image 12.1.MJPEG Image Capturing E16C allow you to capture the MJPEG format monitoring image if needed. You can enable the MJPEG function and set the image quality on the web interface. To configure the configuration on web Surveillance > MJPEG > MJPEG Server interface. Parameter Set-up: Enabled: Tick the check box to enable or disable the Mjpeg service.
E16C Administrator Guide 12.2.Live Stream If you want to check the real-time video from the E16C access control terminal, you can go to the device web interface to obtain the real-time video or you can also enter the correct URL on the web browser to obtain it directly. To see the live stream on web Surveillance > Live Stream interface. To check the real time video using URL, you can Enter the correct URL (http://IP_address:8080/video.
E16C Administrator Guide 12.3.RTSP Stream Monitoring E16C door phone support RTSP stream that allows intercom devices such as indoor monitor or the monitoring unit from the third party to monitor or obtain the the real time audio/ video (RTSP stream) from the door phone using the correct URL. 12.3.1. RTSP Basic Setting You are required to set up RTSP function in terms of RTSP Authorization, authentication, and password etc., before you are able to use the function.
E16C Administrator Guide 12.3.2. RTSP Stream Setting You can select the video codec format for the RTSP stream for the monitoring and you can also configure video resolution and bitrate etc. which based on your actual network environment on the web interface. To configure the configuration on web Surveillance > RTSP > H.264 Video Parameters interface. Parameter Set-up: Video Resolution: select video resolutions among seven options: “QCIF”, “QVGA”,”CIF”,”VGA”,”4CIF”,”720P,””1080P”.
E16C Administrator Guide 2nd Video Bitrate: select video bit-rate among the six options for the second video stream channel. While the second video stream channel is “512 kpbs” by default. Note: E16C supports two video stream channels for H.264 codec video stream. 12.4.
E16C Administrator Guide After the setting is complete, you can enter the ONVIF URL on the third party device to view the video stream. For example: http://IP address:80/onvif/device_service Note: Fill in the specific IP address of the door phone in the URL.
E16C Administrator Guide 13. Logs 13.1. Call Logs If you want to check on the calls inclusive of the dial-out calls , received calls and missed calls in a certain period of time, you can check and search the call log on the device web interface and export the call log from the device if needed. To check the call log, you can go to Intercom > Call Log interface.
E16C Administrator Guide Parameter set-up: Save Door Log Enabled: tick the check box to turn on or turn off the door log function. Status: select between Success and Failed options to search for successful door accesses or Failed door accesses. Time: select the specific time select the specific time span of the door logs you want to search, check or export. Name/Code: select the Name and Code options to search door log by the name or by the PIN code. 13.3.
E16C Administrator Guide 14. Debug 14.1.System Log for Debugging System log in the access control terminal can be used for debugging purpose. If you want to export the system out to a local PC or to a remote server for debugging, you can set up the function on the web Upgrade > Advanced > System Log interface. Parameter Set-up: LogLevel: select log levels from 1 to 7 levels. You will be instructed by Akuvox technical staff about the specific log level to be entered for debugging purpose.
E16C Administrator Guide 14.2.PCAP for Debugging PCAP in E16C access control terminal is used to capture the data package going in and out of the devices for debugging and troubleshooting purpose. You can set up the PCAP on the device web Upgrade > Advanced > PCAP interface properly before using it. Parameter set-up: Specific Port: select the specific ports from 1-65535 so that only the data packet from the specific port can be captured. You can leave the field blank by default.
E16C Administrator Guide 15. Firmware Upgrade Firmware of different versions for E16C access control terminal can be upgraded on the device web Upgrade > Basic interface. Note: Firmware files should be .zip format for upgrade.
E16C Administrator Guide 16. Backup Configuration files can be imported to or exported out of the device to your local PC on the device web Upgrade > Advanced > Others interface if needed.
E16C Administrator Guide 17. Auto-provisioning via Configuration File Configurations and upgrading on E16C door phone can be done on the web interface via one-time auto-provisioning and scheduled auto- provisioning via configuration files, thus saving you from setting up configuration needed one by one manually on the door phone. 17.1.Provisioning Principle Auto-provisioning is a feature used to configure or upgrade the devices in batch via third party servers.
E16C Administrator Guide 17.2. Configuration Files for Auto-provisioning Configuration files have two formats for the auto-provisioning. one is the general configuration files used for the general provisioning and other one is the MAC-based configuration provisioning.
E16C Administrator Guide Parameter Set-up: Power On: select Power on, if you want the device to perform Autop every time it boots up. Repeatedly: select Repeatedly, if you want the device to perform autop according to the schedule you set up. Power On + Repeatedly: select Power On + Repeatedly if you want to combine Power On Mode and Repeatedly mode that will enable the device to perform Autop every time it boots up or according to the schedule you set up.
E16C Administrator Guide Note: The custom Option type must be a string. The value is the URL of TFTP server. Parameter set-up: Custom Option: enter the DHCP code that matched with corresponding URL so that device will find the configuration file server for the configuration or upgrading.
E16C Administrator Guide DHCP Option 66: If none of the above is set, the device will automatically use DHCP Option 66 for getting the upgrade server URL. This is done within the software and the user does not need to specify this. To make it work, you need to configure the DHCP server for the option 66 with the update server URL in it. DHCP Option 43: If the device does not get an URL from DHCP Option 66, it will automatically use DHCP Option 43.
E16C Administrator Guide Parameter set-up: URL: set up tftp，http，https，ftp server address for the provisioning. User Name: set up a user name if the server needs an user name to be accessed to otherwise leave it blank. Password: set up a password if the server needs a password to be accessed to otherwise leave it blank. Common AES Key: set up AES code for the intercom to decipher general Auto Provisioning configuration file.
E16C Administrator Guide Note: Server Address format: TFTP: tftp://192.168.0.19/ FTP: ftp://192.168.0.19/ (allows anonymous login) ftp://username:password@192.168.0.19/(requires a user name and password) HTTP: http://192.168.0.19/ (use the default port 80) http://192.168.0.19:8080/ (use other ports, such as 8080) HTTPS: https://192.168.0.19/ (use the default port 443) Tip: Akuvox do not provide user specified server. Please prepare TFTP/FTP/HTTP/HTTPS server by yourself.
E16C Administrator Guide 18. Integration with Third Party Device 18.1.Integration via Wiegand If you want to integrate the E16C access control terminal with the third-party devices via Wiegand, you can configure the Wiegand on the web Device > Wiegand > Wiegand interface. Parameter Set-up: Wiegand Display Mode：select Wigand Card code format among 8H10D; 6H3D5D; 6H8D; 8HN; 8HR; RAW.
E16C Administrator Guide Wiegand Input Data Order：set the Wiegand input data sequence between “ Normal” and “Reversed” if you select “ Reversed” then the input card number will be reversed an vice versa. Wiegand Output Data Order: set the Wiegand output data sequence between “ Normal” and “Reversed” if you select “ Reversed” then the input card number will be reversed an vice versa.
E16C Administrator Guide NO. Integration Mode Description 1 None If you select “None” then the RS485 integration will be disabled. 2 OSDP If you Select “OSDP” Mode, then the integration communication between the E16C door phone and the third party device is via OSDP protocol. You are required to check for the device integration protocol and make sure if that they use the same integration protocol. 18.3.
E16C Administrator Guide the system. Note: Dummy card numbers can not be sent if “OSDP” is not selected in the RS485 list field.
E16C Administrator Guide 19. Password Modification On the device web interface, you can set and change password for accessing the web Security > Basic > Web Password Modify interface. In addition, you can also select the user role when setting passwords. To set up the Project PIN code, you can go to Project PIN section.
E16C Administrator Guide 20. System Reboot&Reset 20.1.Reboot If you want to restart the device, you can operate it on the device web Upgrade > Basic interface as well. Moreover, you can set up schedule for the device to be restarted. To set up the device restart schedule on web Upgrade > Advanced > Reboot Schedule interface.
E16C Administrator Guide 20.2.Reset If you want to reset the device system to the factory setting, you can it on the web Upgrade > Basic interface.
E16C Administrator Guide 21.
E16C Administrator Guide PCMA: Pulse Code Modulation A-Law PCMU: Pulse Code Modulation µ-Law PCAP: Packet Capture PNP: Plug and Play RFID: Radio Frequency Identification RTP: Real-time Transport Protocol RTSP: Real Time Streaming Protocol MPEG: Moving Picture Experts Group MWI: Message Waiting Indicator NO: Normal Opened NC: Normal Connected NTP: Network Time Protocol NAT: Network Address Translation NVR: Network Video Recorder ONVIF: Open Network Video Interface Forum SIP: Session Initiation Protocol SNMP:
E16C Administrator Guide 22. Contact Us For more information about the product, please visit us at www.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: support@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products.
