Product Info

ManualsBrandsAKUVOX NETWORKS ManualsElectronicsDoor Phone/Access Control Terminal

Table Of Contents

1.Product Overview
2.Change Log
3.Introduction to Configuration Menu
4.Access the Device
- 4.1.Access the Device Setting on the device
- 4.2.Access the Device Setting on the Web Interface
5.Time and Language Setting
- 5.1.Language Setting
- 5.2.Time Setting
- 5.3.LED Setting
  - 5.3.1. Configure Card Reader LED Setting
  - 5.3.2. Configure LED White Light Setting
- 5.4.Screen Display configuration
  - 5.4.1.Configure Screensaver
  - 5.4.2.Upload Screensaver
- 5.5.Volume & Tone Configuration
6.Network Setting
- 6.1.Device Network Connection Setting
- 6.2.Device Deployment in Network
- 6.3.NAT Setting
7.Intercom Call Configuration
- 7.1.IP call & IP Call Configuration
  - 7.1.1.Make IP calls
  - 7.1.2.IP Call Configuration
- 7.2.SIP Call &SIP Call Configuration
- 7.3.Call Auto-answer Configuration
- 7.4.Call Settings
- 7.5.Configure DTMF Data Transmission
8.Relay Switch Setting
- 8.1.Relay Switch Setting
- 8.2.Web Relay Setting
  - 8.2.1.Configure Web Relay on the Web Interface
  - 8.2.2.Configure Web Relay on the Device
9.Door Access Schedule Management
- 9.1. Configure Door Access Schedule
10.Door Unlock Configuration
- 10.1.Configure PIN Code for Door Unlock
- 10.2.Configure RF Card for Door Unlock
- 10.3. Configure Door Access Using Configured Files.
- 10.4.Editing the User(s)-specific door access data
- 10.4.1.Unlock by QR Code
- 10.4.2.Unlock by Bluetooth
- 10.4.3.Unlock by HTTP Command on Web Browser
- 10.4.4.Unlock by Exit Button by the Door
- 10.4.5.Unlock by Reception Tab
- 10.4.6.Unlock by DTMF Code
- 10.4.7.Body Temperature Measurement for Door Access（Optio
  - 10.4.7.1.Body Temperature Measurement Configuration
  - 10.4.7.2.Ambient Temperature Configuration
11.Security
- 11.1.Tamper Alarm Setting
- 11.2.Security Notification Setting
- 11.3.Web Interface Automatic Log-out
12.Monitor and Image
- 12.1.MJPEG Image Capturing
- 12.2.Live Stream
- 12.3.RTSP Stream Monitoring
  - 12.3.1.RTSP Basic Setting
  - 12.3.2.RTSP Stream Setting
- 12.4. ONVIF
13.Logs
- 13.1. Call Logs
- 13.2.Door Logs
- 13.3.Temperature Log
14.Debug
- 14.1.System Log for Debugging
- 14.2.PCAP for Debugging
15.Firmware Upgrade
16.Backup
17.Auto-provisioning via Configuration File
- 17.1.Provisioning Principle
- 17.2. Configuration Files for Auto-provisioning
- 17.3.AutoP Schedule
- 17.4.DHCP Provisioning Configuration
- 17.5.Static Provisioning Configuration
18.Integration with Third Party Device
- 18.1.Integration via Wiegand
- 18.2. Integration via RS485
- 18.3. OSDP Setting
19.Password Modification
20.System Reboot&Reset
- 20.1.Reboot
- 20.2.Reset
21.Abbreviations
22. Contact Us

E16C Administrator Guide

AKUVOX SMART INTERCOM www.akuvox.com

Note:

 IR LED light should be triggered first before the white light can be

valid in the facial recognition, however IR LED light does not need to

be triggered for the white light function in the QR code scan.

5.4. Screen Display configuration

E16C door phones allow you to enjoy a variety of screen displays to enrich

your visual and operational experience through the customized setting to

your preference.

5.4.1.Configure Screensaver

Await screen is mainly a function for the screen protection. You can make the

device to go into idle status for a predefined time span when there is no

operation on the device, or no one is detected approaching. To configure the

configuration on web Device > LCD > Standby Interface Display interface.

Parameter Set-up

 ScreenSaver Mode: tick the check box to enable the screen saver

function.

 Sleep: set the screen saver start time range from “5” seconds to “ 30”

minutes For example, if you set it as “ 15 seconds” then the device will go

into screen saver mode in 15 second when when there is no operation on

the device or no one is detected approaching.