Product Info

ManualsBrandsAKUVOX NETWORKS ManualsElectronicsDoor Phone/Access Control Terminal

Table Of Contents

1.Product Overview
2.Change Log
3.Introduction to Configuration Menu
4.Access the Device
- 4.1.Access the Device Setting on the device
- 4.2.Access the Device Setting on the Web Interface
5.Time and Language Setting
- 5.1.Language Setting
- 5.2.Time Setting
- 5.3.LED Setting
  - 5.3.1. Configure Card Reader LED Setting
  - 5.3.2. Configure LED White Light Setting
- 5.4.Screen Display configuration
  - 5.4.1.Configure Screensaver
  - 5.4.2.Upload Screensaver
- 5.5.Volume & Tone Configuration
6.Network Setting
- 6.1.Device Network Connection Setting
- 6.2.Device Deployment in Network
- 6.3.NAT Setting
7.Intercom Call Configuration
- 7.1.IP call & IP Call Configuration
  - 7.1.1.Make IP calls
  - 7.1.2.IP Call Configuration
- 7.2.SIP Call &SIP Call Configuration
- 7.3.Call Auto-answer Configuration
- 7.4.Call Settings
- 7.5.Configure DTMF Data Transmission
8.Relay Switch Setting
- 8.1.Relay Switch Setting
- 8.2.Web Relay Setting
  - 8.2.1.Configure Web Relay on the Web Interface
  - 8.2.2.Configure Web Relay on the Device
9.Door Access Schedule Management
- 9.1. Configure Door Access Schedule
10.Door Unlock Configuration
- 10.1.Configure PIN Code for Door Unlock
- 10.2.Configure RF Card for Door Unlock
- 10.3. Configure Door Access Using Configured Files.
- 10.4.Editing the User(s)-specific door access data
- 10.4.1.Unlock by QR Code
- 10.4.2.Unlock by Bluetooth
- 10.4.3.Unlock by HTTP Command on Web Browser
- 10.4.4.Unlock by Exit Button by the Door
- 10.4.5.Unlock by Reception Tab
- 10.4.6.Unlock by DTMF Code
- 10.4.7.Body Temperature Measurement for Door Access（Optio
  - 10.4.7.1.Body Temperature Measurement Configuration
  - 10.4.7.2.Ambient Temperature Configuration
11.Security
- 11.1.Tamper Alarm Setting
- 11.2.Security Notification Setting
- 11.3.Web Interface Automatic Log-out
12.Monitor and Image
- 12.1.MJPEG Image Capturing
- 12.2.Live Stream
- 12.3.RTSP Stream Monitoring
  - 12.3.1.RTSP Basic Setting
  - 12.3.2.RTSP Stream Setting
- 12.4. ONVIF
13.Logs
- 13.1. Call Logs
- 13.2.Door Logs
- 13.3.Temperature Log
14.Debug
- 14.1.System Log for Debugging
- 14.2.PCAP for Debugging
15.Firmware Upgrade
16.Backup
17.Auto-provisioning via Configuration File
- 17.1.Provisioning Principle
- 17.2. Configuration Files for Auto-provisioning
- 17.3.AutoP Schedule
- 17.4.DHCP Provisioning Configuration
- 17.5.Static Provisioning Configuration
18.Integration with Third Party Device
- 18.1.Integration via Wiegand
- 18.2. Integration via RS485
- 18.3. OSDP Setting
19.Password Modification
20.System Reboot&Reset
- 20.1.Reboot
- 20.2.Reset
21.Abbreviations
22. Contact Us

E16C Administrator Guide

 Payload: select the payload type (ranging from 90-118) to configure the

audio codec payload. The pay load between the door phone and the

corresponding intercom device should be identical. The default payload

is 104.

7.5. Configure DTMF Data Transmission

In order to achieve the door access via DTMF code or some other

applications, you are required to properly configure DTMF in order to

establish a DTMF-based data transmission between the door phone and

other intercom device for the third party integration. To configure the DTMF

data transmission, you can go to Account > Advanced > DTMF.

Parameter Set-up:

 Mode: select DTMF mode among five options: “Inband”, “RFC2833”,

“Info+Inband” and “Info+RFC2833” based on the specific DTMF

transmission type of the third party device to be matched with as the

party for receiving signal data.

 How to Notify DTMF：select among four types: “Disable” “ DTMF”

“DTMF-Relay” “Telephone-Event” according to the specific type adopted

by the third party device. You are required to set it up only when the third

party device to be matched with adopts “Info” mode.

 Payload: set the payload according the the specific data transmission

payload agreed on between the sender and receiver during the data

transmission.