Product Info

ManualsBrandsAKUVOX NETWORKS ManualsElectronicsDoor Phone/Access Control Terminal

Table Of Contents

1.Product Overview
2.Change Log
3.Introduction to Configuration Menu
4.Access the Device
- 4.1.Access the Device Setting on the device
- 4.2.Access the Device Setting on the Web Interface
5.Time and Language Setting
- 5.1.Language Setting
- 5.2.Time Setting
- 5.3.LED Setting
  - 5.3.1. Configure Card Reader LED Setting
  - 5.3.2. Configure LED White Light Setting
- 5.4.Screen Display configuration
  - 5.4.1.Configure Screensaver
  - 5.4.2.Upload Screensaver
- 5.5.Volume & Tone Configuration
6.Network Setting
- 6.1.Device Network Connection Setting
- 6.2.Device Deployment in Network
- 6.3.NAT Setting
7.Intercom Call Configuration
- 7.1.IP call & IP Call Configuration
  - 7.1.1.Make IP calls
  - 7.1.2.IP Call Configuration
- 7.2.SIP Call &SIP Call Configuration
- 7.3.Call Auto-answer Configuration
- 7.4.Call Settings
- 7.5.Configure DTMF Data Transmission
8.Relay Switch Setting
- 8.1.Relay Switch Setting
- 8.2.Web Relay Setting
  - 8.2.1.Configure Web Relay on the Web Interface
  - 8.2.2.Configure Web Relay on the Device
9.Door Access Schedule Management
- 9.1. Configure Door Access Schedule
10.Door Unlock Configuration
- 10.1.Configure PIN Code for Door Unlock
- 10.2.Configure RF Card for Door Unlock
- 10.3. Configure Door Access Using Configured Files.
- 10.4.Editing the User(s)-specific door access data
- 10.4.1.Unlock by QR Code
- 10.4.2.Unlock by Bluetooth
- 10.4.3.Unlock by HTTP Command on Web Browser
- 10.4.4.Unlock by Exit Button by the Door
- 10.4.5.Unlock by Reception Tab
- 10.4.6.Unlock by DTMF Code
- 10.4.7.Body Temperature Measurement for Door Access（Optio
  - 10.4.7.1.Body Temperature Measurement Configuration
  - 10.4.7.2.Ambient Temperature Configuration
11.Security
- 11.1.Tamper Alarm Setting
- 11.2.Security Notification Setting
- 11.3.Web Interface Automatic Log-out
12.Monitor and Image
- 12.1.MJPEG Image Capturing
- 12.2.Live Stream
- 12.3.RTSP Stream Monitoring
  - 12.3.1.RTSP Basic Setting
  - 12.3.2.RTSP Stream Setting
- 12.4. ONVIF
13.Logs
- 13.1. Call Logs
- 13.2.Door Logs
- 13.3.Temperature Log
14.Debug
- 14.1.System Log for Debugging
- 14.2.PCAP for Debugging
15.Firmware Upgrade
16.Backup
17.Auto-provisioning via Configuration File
- 17.1.Provisioning Principle
- 17.2. Configuration Files for Auto-provisioning
- 17.3.AutoP Schedule
- 17.4.DHCP Provisioning Configuration
- 17.5.Static Provisioning Configuration
18.Integration with Third Party Device
- 18.1.Integration via Wiegand
- 18.2. Integration via RS485
- 18.3. OSDP Setting
19.Password Modification
20.System Reboot&Reset
- 20.1.Reboot
- 20.2.Reset
21.Abbreviations
22. Contact Us

E16C Administrator Guide

Parameter Set-up:

 Validity Term: select validity term among three options: Always, Schedule

and Never. if you select Always, then the door access via PIN code will

always be valid with no restriction. If you select Schedule, then you are

required to select among the created schedule for user-based PIN code

access. If you select Never then the PIN code access will never be valid.

 Frequency: set the total number of valid PIN code access allowed.

 All Schedule: select from the created door access schedule on the right

box and move the one to be applied to the user(s)-specific PIN code door

access to the box on the right side.

Note:

 This step is applicable to door access by RF card and facial

recognition as they are identical in configuration.

10.1.4. Configure Private PIN Access Mode

E16C door phones offer you two types of access modes for private PIN code

access, namely “ PIN” and “ APT#+PIN”. To configure the access mode, you

can go to Access Control > PIN Setting > Private PIN to select Authorization

Mode.