Product Info

ManualsBrandsAKUVOX NETWORKS ManualsElectronicsDoor Phone/Access Control Terminal

Table Of Contents

1.Product Overview
2.Change Log
3.Introduction to Configuration Menu
4.Access the Device
- 4.1.Access the Device Setting on the device
- 4.2.Access the Device Setting on the Web Interface
5.Time and Language Setting
- 5.1.Language Setting
- 5.2.Time Setting
- 5.3.LED Setting
  - 5.3.1. Configure Card Reader LED Setting
  - 5.3.2. Configure LED White Light Setting
- 5.4.Screen Display configuration
  - 5.4.1.Configure Screensaver
  - 5.4.2.Upload Screensaver
- 5.5.Volume & Tone Configuration
6.Network Setting
- 6.1.Device Network Connection Setting
- 6.2.Device Deployment in Network
- 6.3.NAT Setting
7.Intercom Call Configuration
- 7.1.IP call & IP Call Configuration
  - 7.1.1.Make IP calls
  - 7.1.2.IP Call Configuration
- 7.2.SIP Call &SIP Call Configuration
- 7.3.Call Auto-answer Configuration
- 7.4.Call Settings
- 7.5.Configure DTMF Data Transmission
8.Relay Switch Setting
- 8.1.Relay Switch Setting
- 8.2.Web Relay Setting
  - 8.2.1.Configure Web Relay on the Web Interface
  - 8.2.2.Configure Web Relay on the Device
9.Door Access Schedule Management
- 9.1. Configure Door Access Schedule
10.Door Unlock Configuration
- 10.1.Configure PIN Code for Door Unlock
- 10.2.Configure RF Card for Door Unlock
- 10.3. Configure Door Access Using Configured Files.
- 10.4.Editing the User(s)-specific door access data
- 10.4.1.Unlock by QR Code
- 10.4.2.Unlock by Bluetooth
- 10.4.3.Unlock by HTTP Command on Web Browser
- 10.4.4.Unlock by Exit Button by the Door
- 10.4.5.Unlock by Reception Tab
- 10.4.6.Unlock by DTMF Code
- 10.4.7.Body Temperature Measurement for Door Access（Optio
  - 10.4.7.1.Body Temperature Measurement Configuration
  - 10.4.7.2.Ambient Temperature Configuration
11.Security
- 11.1.Tamper Alarm Setting
- 11.2.Security Notification Setting
- 11.3.Web Interface Automatic Log-out
12.Monitor and Image
- 12.1.MJPEG Image Capturing
- 12.2.Live Stream
- 12.3.RTSP Stream Monitoring
  - 12.3.1.RTSP Basic Setting
  - 12.3.2.RTSP Stream Setting
- 12.4. ONVIF
13.Logs
- 13.1. Call Logs
- 13.2.Door Logs
- 13.3.Temperature Log
14.Debug
- 14.1.System Log for Debugging
- 14.2.PCAP for Debugging
15.Firmware Upgrade
16.Backup
17.Auto-provisioning via Configuration File
- 17.1.Provisioning Principle
- 17.2. Configuration Files for Auto-provisioning
- 17.3.AutoP Schedule
- 17.4.DHCP Provisioning Configuration
- 17.5.Static Provisioning Configuration
18.Integration with Third Party Device
- 18.1.Integration via Wiegand
- 18.2. Integration via RS485
- 18.3. OSDP Setting
19.Password Modification
20.System Reboot&Reset
- 20.1.Reboot
- 20.2.Reset
21.Abbreviations
22. Contact Us

E16C Administrator Guide

11. Security

11.1.Tamper Alarm Setting

Tamper alarm function serves as a protection against any unauthorized

removal of the devices by triggering off the temper alarm on the device. To

configure the configuration on web Security > Basic > Temper Alarm

interface.

Parameter Set-up:

 Enable: tick the check box to enable the temper alarm function. When the

temper alarm goes off , you can press the Disarm tab beside the check

box to clear the alarm.

 Key Status: temper alarm will not be triggered unless the key status is

shifted from “Low” to “ High” status.

Note:

 Disarm tab will turn gray when the temper alarm is cleared.

 The round rubber button at the back of the device must be in

press-down status otherwise the alarm will not be fired.

Note:

 The round rubber button at the back of the device must be in

press-down status otherwise the alarm will not be fired.