Product Info

ManualsBrandsAKUVOX NETWORKS ManualsElectronicsDoor Phone/Access Control Terminal

Table Of Contents

1.Product Overview
2.Change Log
3.Introduction to Configuration Menu
4.Access the Device
- 4.1.Access the Device Setting on the device
- 4.2.Access the Device Setting on the Web Interface
5.Time and Language Setting
- 5.1.Language Setting
- 5.2.Time Setting
- 5.3.LED Setting
  - 5.3.1. Configure Card Reader LED Setting
  - 5.3.2. Configure LED White Light Setting
- 5.4.Screen Display configuration
  - 5.4.1.Configure Screensaver
  - 5.4.2.Upload Screensaver
- 5.5.Volume & Tone Configuration
6.Network Setting
- 6.1.Device Network Connection Setting
- 6.2.Device Deployment in Network
- 6.3.NAT Setting
7.Intercom Call Configuration
- 7.1.IP call & IP Call Configuration
  - 7.1.1.Make IP calls
  - 7.1.2.IP Call Configuration
- 7.2.SIP Call &SIP Call Configuration
- 7.3.Call Auto-answer Configuration
- 7.4.Call Settings
- 7.5.Configure DTMF Data Transmission
8.Relay Switch Setting
- 8.1.Relay Switch Setting
- 8.2.Web Relay Setting
  - 8.2.1.Configure Web Relay on the Web Interface
  - 8.2.2.Configure Web Relay on the Device
9.Door Access Schedule Management
- 9.1. Configure Door Access Schedule
10.Door Unlock Configuration
- 10.1.Configure PIN Code for Door Unlock
- 10.2.Configure RF Card for Door Unlock
- 10.3. Configure Door Access Using Configured Files.
- 10.4.Editing the User(s)-specific door access data
- 10.4.1.Unlock by QR Code
- 10.4.2.Unlock by Bluetooth
- 10.4.3.Unlock by HTTP Command on Web Browser
- 10.4.4.Unlock by Exit Button by the Door
- 10.4.5.Unlock by Reception Tab
- 10.4.6.Unlock by DTMF Code
- 10.4.7.Body Temperature Measurement for Door Access（Optio
  - 10.4.7.1.Body Temperature Measurement Configuration
  - 10.4.7.2.Ambient Temperature Configuration
11.Security
- 11.1.Tamper Alarm Setting
- 11.2.Security Notification Setting
- 11.3.Web Interface Automatic Log-out
12.Monitor and Image
- 12.1.MJPEG Image Capturing
- 12.2.Live Stream
- 12.3.RTSP Stream Monitoring
  - 12.3.1.RTSP Basic Setting
  - 12.3.2.RTSP Stream Setting
- 12.4. ONVIF
13.Logs
- 13.1. Call Logs
- 13.2.Door Logs
- 13.3.Temperature Log
14.Debug
- 14.1.System Log for Debugging
- 14.2.PCAP for Debugging
15.Firmware Upgrade
16.Backup
17.Auto-provisioning via Configuration File
- 17.1.Provisioning Principle
- 17.2. Configuration Files for Auto-provisioning
- 17.3.AutoP Schedule
- 17.4.DHCP Provisioning Configuration
- 17.5.Static Provisioning Configuration
18.Integration with Third Party Device
- 18.1.Integration via Wiegand
- 18.2. Integration via RS485
- 18.3. OSDP Setting
19.Password Modification
20.System Reboot&Reset
- 20.1.Reboot
- 20.2.Reset
21.Abbreviations
22. Contact Us

E16C Administrator Guide

18.3. OSDP Setting

If you choose OSDP integration mode, you can not only check for OSDP

status but also obtain the authentication from the third-party devices for

various applications such as door access etc. To configure the configuration

on web Device > RS485 > OSDP Advance Setting interface.

Parameter Set-up:

 Connect Status: indicate OSDP based communication status.

 Send by: select in what way you want to send out the card number

among three options: OSDP, Wiegand and None. if you select OSDP then

the card number will be sent out to the third party devices via RS485. if

you select Wiegand then the card number will be sent out via wiegand. If

you select None then the card number will not be sent out but retained in

NO.

Integration Mode

Description

None

If you select “None” then the RS485

integration will be disabled.

OSDP

If you Select “OSDP” Mode, then the

integration communication between the

E16C door phone and the third party device is

via OSDP protocol. You are required to check

for the device integration protocol and make

sure if that they use the same integration

protocol.