Product Info
Table Of Contents
- 1.1.Device Start-up Network Selection
- 1.2.Device Home Screen Type Selection
- 1.3.Accessing the Device Setting on the Device
- 1.4.Access the Device Setting on the Web Interface
- 1.5.Language Setting
- 1.6.Time Setting
- 1.7.Screen Display setting on the Device
- 1.8.Screen Display Setting on the Web Interface
- 1.9.Screensaver Configuration
- 1.10.Upload Wall Paper
- 1.11.Status Bar
- 1.12.Upload Device Booting Image
- 1.13.Icon Screen Display Configuration
- 1.14.Volume Configuration
- 1.15.Phone Book Configuration on the Device
- 1.16.Phone Book Configuration on the Web Interface
- 1.17.Device Network Configuration
- 1.18.Device Deployment in Network
- 1.19. Device NAT Setting
- 1.20. Device Bluetooth Setting
- 1.21.Device Wi-Fi Setting
- 1.22.IP call & IP Call Configuration
- 1.23.SIP Call &SIP Call Configuration
- 1.24.SIP Account Registration
- 1.25.SIP Server Configuration
- 1.26.Outbound Proxy Server configuration
- 1.27.SIP Call DND & Return Code Configuration
- 1.28.Device Local RTP configuration
- 1.29.Data Transmission Type Configuration
- 1.30.Call Setting
- 1.31. Intercom Call Configuration
- 1.32.PTime Configuration
- 1.33.SIP Hacking Protection
- 1.34.Emergency Call Setting
- 1.35.RF Setting (Optional)
- 1.36.Multicast Configuration
- 1.37.Call Forwarding Setting
- 1.38.Manage Messages
- 1.39. Configure Voice Message (MWI)
- 1.40.Audio Codec Configuration
- 1.41.Video Codec Configuration
- 1.42.Monitor and Image
- 1.43.Alarm and Arming Configuration
- 1.44.Screen Unlock Setting
- 1.45.Voice Encryption
- 1.46.Remote Control
- 1.47.Relay Switch Setting
- 1.48.Web Relay Setting
- 1.49.Door Unlock Configuration
- 1.50.Configure Lift Control
- 1.51.Configure Lift Control Prompt
- 1.52.Provisioning Principle
- 1.53.Introduction to the Configuration Files for Auto-P
- 1.54.Autop Schedule
- 1.55.DHCP Provisioning Configuration
- 1.56.Static Provisioning Configuration
- 1.57.System Log for Debugging
- 1.58. PCAP for Debugging
- 1.59. User Agent
- 1.60.Enter Applications Screen
- 1.61. Install Third-party App
- 1.62.Modify Device Basic Setting Password
- 1.63.Modify Device Advanced Setting Password
- 1.64.Modify Device Web Interface Password
- 1.65.Modify Browser Password
- 1.66.PBX Configuration on The Device
- 1.67.PBX Configuration on The Web Interface
- 1.68.Reboot
- 1.69. Reset
Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment .
This transmitter must not be co ‐ located or operating in conjunction with
any other antenna or transmitter.
Ｔｈｉｓ ｅｑｕｉｐｍｅｎｔ ｓｈｏｕｌｄ ｂｅ ｉｎｓｔａｌｌｅｄ ａｎｄ ｏｐｅｒａｔｅｄ ｗｉｔｈ ｍｉｎｉｍｕｍ ｄｉｓｔａｎｃｅ ２０ｃｍ
ｂｅｔｗｅｅｎ ｔｈｅ ｒａｄｉａｔｏｒ＆ ｙｏｕｒ ｂｏｄｙ．