R26B Door Phone Admin Guide
About this manual Thank you for choosing Akuvox’s R26B door phone. This manual is intended for end userswho need to properly configure the door phone. This manualis applicable to 26.31.4.xx version, and it provides all functions’ configurations of R26B. Please visit Akuvox forum or consult technical support for any new information or latest firmware. Note: Please refer to universal abbreviation form in the end of manual when meet any abbreviation letter.
—Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help.
Content 1. Product Overview...............................................................................................................................................................................................1 1.1. Product Description................................................................................................................................................................................... 1 1.2. Connector Introduction...........................................................
3.2.1. Modify the Web Password............................................................................................................................................................. 6 3.3. Phone Configuration..................................................................................................................................................................................6 3.3.1. Language.......................................................................................................
3.4.3. Auto Answer................................................................................................................................................................................... 16 3.4.4. Web Call......................................................................................................................................................................................... 17 3.4.5. Push To Hang Up.....................................................................................
4.1.2. IR LED.............................................................................................................................................................................................26 4.1.3. RF Card Code Display Related...................................................................................................................................................27 4.2. Intercom.............................................................................................................
4.4.3. Action...............................................................................................................................................................................................35 4.4.3.1. Action Parameters..................................................................................................................................................................... 35 4.4.3.2. Push Button Action...................................................................................
R26B Admin Guide 1. Product Overview 1.1. Product Description Akuvox R26B is a SIP-compliant, hands-free, five buttons door phone. It can be connected with Akuvox indoor monitors for remote unlock control and monitor. Users can operate the indoor phone to communicate with visitors via voice and video. Users can also use RFID cards to unlock the door It’s applicable in villas, office and so on. Figure 1.1 Product Description 1.2.
R26B Admin Guide DOOR A/B: Trigger signal input terminal. Relay A/B (NO/NC/COM): Relay control terminal. Note: The general door phone interface diagram is only for reference. 1.3. LED Status Information LED Status Blue Description Always on Normal status Flashing Calling Red Flashing Network is unavailable Green Always on Talking on a call Flashing Receiving a call Flashing Upgrading Pink Figure 1.
R26B Admin Guide 2. Daily Use 2.1. Making a Call Press one of the call buttons to call out the predefined SIP account or IP address and if LED turns green, it means the call has been answered. 2.2. Receiving a Call User can use IP phone or indoor monitor to call R26B and R26Bwill answer it automatically by default. If user disable auto answer, pressing button to answer incoming call.
R26B Admin Guide 2.3. Unlock 2.3.1. Unlock by RFID Cards Place the predefined user cards in RFID card reader to unlock. Under normal conditions, R26B will announce “The door is now opened.” 13.56 MHz RF card is supported on R26B. 2.3.2. Unlock by DTMF Codes Users can press the predefined DTMF code from an answer unit to remotely unlock the door during the call. Users will also hear “The door is now opened.
R26B Admin Guide 3. Basic Setting 3.1. Getting Started 3.1.1. IP Announcement While R26B starts up normally, hold the top of call button for several seconds after the Status LED turns blue, voice system will enter IP announcement mode. In announcement mode, the IP address will be announced periodically and “IP 0.0.0.0” would be announced if no IP address is gained. Press call button again to quit the announcement mode. 3.1.2.
R26B Admin Guide User Name: admin Password: admin Note: The recommended browser is Google Chrome. 3.2. Password Modification 3.2.1. Modify the Web Password Go to Security - Basic to modify password for webpage. To modify Figure 3.2.1 Modify the web password password for“admin” or “user” account. 3.3. Phone Configuration 3.3.1. Language Figure 3.3.1Language Go to Phone-Time/Lang to select language for webpage.
R26B Admin Guide 3.3.2. Time Go to Phone - Time/Langto configure it. Time Zone: To select local time zone for NTP server. Primary Server: To configure primary NTP server address. Secondary Server: To configure secondary NTP server address, it Figure 3.3.2 Time takes effect if primary NTP server is unreachable. Update Interval: To configure interval between two consecutive NTP requests. System Time: The current time of the phone. 3.3.3. Network DHCP Mode In website, go to Network - Basic. Figure 3.3.3.
R26B Admin Guide R26B uses DHCP mode by default which will get IP address, subnet mask, default gateway and DNS server address from DHCP server automatically. Static IP Mode In Website, go to Network - Basic. If select static IP, users should manually setup IP address, subnet mask, default gateway and DNS server address. The figure right shows static IP settings. Local RTP Go to Network - Advanced to configure. Local RTP:To display and configure local RTP settings.
R26B Admin Guide SNMP Go to Network - Advanced to configure. SNMP:To display and configure SNMP settings. Active: To enable or disable SNMP feature. Figure 3.3.3-3 SNMP Port: To configure SNMP server’s port. Trusted IP: To configure allowed SNMP server address. It could be an IP address or any valid URL domain name. Note: SNMP is Internet-standard protocol for managing devices on IP networks. 3.3.3.1. VLAN Go to Network - Advanced to configure. VLAN:To display and configure VLAN settings. Figure 3.3.3.
R26B Admin Guide Note: Please consult administrator for specific VLAN settings in the networking environment. 3.3.3.2. TR069 Go to Network - Advanced to configure. TR069:To display and configure TR069 settings. Active: To enable or disable TR069 feature. Version: To select supported TR069 version (version 1.0 or 1.1). ACS/CPE: ACS is short for auto configuration servers as server side, and CPE is short for customer-premise equipment as client side devices. URL:To configure URL address for ACS or CPE.
R26B Admin Guide Note:TR-069 is a technical specification entitled CPE WAN Management Protocol (CWMP).It defines an application layer protocol for remote management of end-user devices. 3.3.4. Sound Go to Phone-Voice to configure volume and upload tone file. Mic Volume: To configure microphone volume. Speaker Volume:To configure speaker volume. Open Door Warning: Disable it, and users will not hear the prompt voice when the door is opened.
R26B Admin Guide 3.3.5. DND Go to Phone - Call Featureto configure DND feature. DND:DND allows phones to ignore any incoming calls. Return Code when DND: Determine what response code should be sent back to server when there is an incoming call if DND is on. DND On Code: The code is used to turn on DND on server’s side, if configured, door phones will send a SIP message to server to turn on DND on server side if users press DND when DND is off.
R26B Admin Guide 3.4. Intercom Call 3.4.1. Direct IP Call Without sip server, users can also use IP address to call each other, but this way is only suitable in the LAN. Figure 3.4.1-1 Direct IP call Go to Phone - Call Feature to enable the direct IP call for door phones first. Go to Intercom - Basic to configure the IP address of the destination(E.g.IP address 192.168.10.91).One button for each button.After, press the push button to make direct IP call.
R26B Admin Guide 3.4.2. SIP Call SIP calls which use SIP numbers to make or receive calls should be supported by SIP server. Users need to register accounts and fill SIP feature parameters before using it. Go to Account - Basic to configure SIP account and SIP server for door phones first. 3.4.2.1. SIP Account Status: To display register result. Display Label: To configure label displayed. Display Name: To configure name sent to the other call party for displaying.
R26B Admin Guide 3.4.2.2. SIP Server 1&2 Server IP 1: To enter SIP server’s IP address or URL. Server IP 2: To display and configure secondary SIP server settings. This is for redundancy, if registering to primary SIP server fails, the phone will go to secondary SIP server for registering. Registration Period: The registration will expire after registration Figure 3.4.2.2 SIP server 1&2 period, and the phone will re-register automatically within registration period. 3.4.2.3.
R26B Admin Guide TLS: Secured and reliable transport layer protocol. DNS-SRV: DNS record for specifying the location of services. 3.4.2.5. NAT To display and configure NAT settings. STUN: Short for session traversal utilities for NAT, a solution to solve NAT issues. Figure 3.4.2.5 NAT Note:By default, NAT is disabled. After configuring SIP call related parameters, users can refer to the direct IP call part to dial out a SIP call. 3.4.3.
R26B Admin Guide 3.4.4. Web Call Go to Intercom-Basic to dial out or answer incoming call from website. Figure 3.4.4 Web call 3.4.5. Push To Hang Up Go to Intercom - Basic to configure. To enable or disable pushing Figure 3.4.5 Push to hang up button to hang up. 3.5. Security 3.5.1. Live view Go to Intercom - Live Stream to check the real-time video from R26B. In addition, user also can check the real-time picture via URL: http://IP_address:8080/picture.jpg. 17 Figure 3.5.
R26B Admin Guide 3.5.2. RTSP R26B supports RTSP stream, go to Intercom - RTSP to enable or disable RTSP server. The URL for RTSP stream is: rtsp://IP_address/live/ch00_0. RTSP Stream: To enable RTSP video and select the video codec. R26B supports H.264 video codec by default. H.264 Video Parameters: H.264 is a video stream compression standard. Different from H.263, it provides an approximately identical level of video stream quality but a half bit rate.
R26B Admin Guide less core program space. To modify the resolution, framerate and bitrate of MPEG4. 3.5.3. ONVIF R26B supports ONVIF protocol, which means R26B’s camera can be searched by other devices, like NVR which supports ONVIF protocol as well. Go to Intercom - ONVIF to configure ONVIF mode, its username and password. Switching ONVIF mode to “Undiscoverable”and it means users must program ONVIF’s URL manually. The ONVIF’s URL is: http://IP_address:8090/onvif/device_service. 19 Figure 3.5.
R26B Admin Guide 3.6. Access Control 3.6.1. Relay Go to Intercom - Relay to configure relay. There are three terminals of relay: NO, NC and COM. NO stands for normally open contact while NC stands for normally closed contact. Relay ID:R26B supports two relays, users can configure them respectively. Relay Type:Default state means NC and COM are normally closed, while invert state means NC and COM are normally opened. Relay Delay:To configure the duration of opened relay.
R26B Admin Guide Multiple DTMF: To configure multiple digits DTMF code for remote unlock. Relay Status:Low means that COM is connecting to NC while High means that COM is connecting to NO. Note:Relay operate a switch and does not deliver power, so users should prepare power adapter for external devices which connects to relay. 3.6.2. Card Setting Go to Intercom - Card setting, to manage card access system. Figure 3.6.
R26B Admin Guide Switch card status to “Card Issuing” and click “Apply”; Place card on the card reader area and click “Obtain”; Name card, choose which door you want to open and the valid day and time; Click “Add” to add it into list. Note: Users can use card to access only when card status has been switched to “Normal”. Door Card Management Valid card information will be shown in the list. Administrator could delete one card’s access permission or empty all the list. Figure 3.6.2-3 Card setting 3.6.3.
R26B Admin Guide URLformat: http://IP_address/fcgi/do?action=OpenDoor&UserName=&Passwor d=&DoorNum=1 3.6.4. Unlock via Exit Button Go to Intercom - Input to configure input settings. R26B supports two input triggers Input A/B (DOOR A/B). Input Service:To enable or disable input trigger service. Trigger Option: To choose open circuit trigger or closed circuit trigger. Low means that connection between door terminal and GND is closed, while high means the connection is opened.
R26B Admin Guide 3.7. Reboot Go to Upgrade - Basic, users can reboot the phone. Figure 3.7 Reboot 3.8. Reset Go to Upgrade - Basic, users can reset the phone to factory settings. 24 Figure 3.8.
R26B Admin Guide 4. Advance Feature 4.1. Phone Configuration 4.1.1. LED Go to Intercom - LED Setting to configure the LED status.To setup the LED lighting mode. State: There is five states: Normal, Offline, Calling, Talking and Receiving. Color Off: The default status is OFF. Figure 4.1.1-1 LED Color On: It can support three color: Red, Green, Blue. Blink Mode: To setup the different blink frequency. LED Control: Use HTTP URL to remote control the LED status. Figure 4.1.
R26B Admin Guide http://PhoneIP/fcgi/do?action=LedAction&State=1&Color=1&Mode =2500 Status: 1=Idle; 2=OffLine; 3=Calling; 4=Talking; 5=Receiving; Color: 1=Green; 2=Blue; 3=Red; Mode: 0=Always On; 1=Always Off; 500/1000/1500/2000/25000/3000 4.1.2. IR LED Go to Intercom - Advanced to configure. Photoresistor: The setting is for night vision, when the surrounding of R26B is very dark, infrared LED will turn on and R26B will turn to night mode.
R26B Admin Guide 4.1.3. RF Card Code Display Related Go to Intercom - Advanced to configure. RFID Display Mode:To be compatible different card number Figure 4.1.3 RF card code display related formats. The default 8HN means hexadecimal. 4.2. Intercom 4.2.1. Call Time Related Figure 4.2.1-1 Call time related Go to Intercom - Basic to configure. Max Call Time: To configure the max call time. Max Dial Time: To configure the max incoming dial time, available when auto answer is disabled. Figure 4.2.
R26B Admin Guide 4.2.2. Return Code When Refuse Figure 4.2.2 Return code when refuse Go to Phone - Call Feature - Others to configure. Return Code When Refuse: Allows users to assign specific code as return code to SIP server when an incoming call is rejected. 4.2.3. SIP Call Related Go to Account-Advanced to configure the SIP call related. Max Local SIP Port: To configure maximum local SIP port for designated SIP account.
R26B Admin Guide Missed Call Log: If enabled, any missed call will be recorded into call log. Prevent Hacking: If enabled, it will prevent SIP messages from hacking. 4.2.4. Codec Go to Account - Advanced to configure SIP call related codec. SIP Account: To choose which account to configure. Audio Codec:R26B support four audio codec: PCMA, PCMU, G729, G722. Different audio codec requires different bandwidth, users can enable/disable them according to different network environment. Figure 4.2.
R26B Admin Guide G729 8kbit/s 8kHz G722 64kbit/s 16kHz Video Codec: R26B supports H.264 standard, which provides better video quality at substantially lower bit rates than previous standards. Codec Resolution: R26B supports four resolutions: QCIF, CIF, Figure 4.2.4-2 Codec VGA, 4CIF and 720P. Codec Bitrate: To configure bit rates of video stream. Codec Payload: To configure RTP audio video profile. Figure 4.2.4-3 Codec Go to Phone - Call Feature to configure multicast related codec. 4.2.5.
R26B Admin Guide How To Notify DTMF: Only available when DTMF type is Info. DTMF Payload: To configure payload type for DTMF. 4.2.6. Session Timer Go to Account - Advanced to configure it. If enabled, the on going call will be disconnected automatically once the session expired unless it’s been refreshed by UAC or UAS. Figure 4.2.6 Session timer 4.2.7. Encryption Go to Account - Advanced to configure it.If enabled, voice will be Figure 4.2.7 Encryption encrypted. 4.2.8.
R26B Admin Guide UDP Alive Msg Interval: Keep alive message interval. Rport: Remote Port, if enabled, it will add remote port into outgoing SIP message for designated account. 4.2.9. User Agent Go to Account - Advanced to configure it. Figure 4.2.9 User agent To customize user agent field in the SIP message. If users agent is set to specific value, users could see the information from network package.
R26B Admin Guide 4.3. Access Control 4.3.1. Web Relay R26B can support extra web relay which is connected with the door phone via network. Figure 4.3.1-1 Web relay Go to Phone - WebRelay to configure. Type: Connect web relay and choose the type. IP Address: Enter web relay’s IP address. UserName: It is an authentication for connecting web relay. Password: It is an authentication for connecting web relay. Web Relay Action: Web relay action is used to trigger the web relay.
R26B Admin Guide Web Relay Extension: The webrelay can only receive the DTMF signal from the corresponding extension number. Note: Users can modify username and password in web relay website. 4.4. Security 4.4.1. Anti-alarm Go to Intercom - Advanced to configure. R26B integrates internal gravity sensor for the own security, and after enabling tamper alarm, if the gravity of R26B changes dramatically, the phone will alarm. Gravity sensor threshold stands for sensitivity of sensor. 34 Figure 4.4.
R26B Admin Guide 4.4.2. Motion R26B supports motion detection, go to Intercom - Motion to configure detection parameter. Figure 4.4.2-1 Motion Motion Detection: To enable or disable motion detection. Motion Delay:To configure minium time gap between two snapshots. Motion Detect Time Setting: To make motion detect time for a whole week. Figure 4.4.2-2 Motion 4.4.3.
R26B Admin Guide Email Notification Sender’s email address: To configure email address of sender. Receiver’s email address: To configure email address of receiver. SMTP server address: To configure SMTP server address of sender. SMTP user name: To configure user name of SMTP service (usually it is same with sender’s email address). SMTP password: To configure password of SMTP service (usually it is same with the password of sender’s email). Figure 4.4.3.
R26B Admin Guide SIP Call Notification SIP Call Number: To configure SIP call number. SIP Call Name: To configure display name of R26B. Three specific actions which will be triggered in R26B: 4.4.3.2. Push Button Action Go to Intercom - Basic to configure. Enable this function, the device will record any changes of the surrounding environment then send the message or picture to the corresponding receiver. Action to execute: Tick the suit the suitable way to receive the action message.
R26B Admin Guide 4.4.3.3. Input Interface Triggered Action Go to Intercom - Input to configure. Action to execute: To choose which action to execute after triggering. Http URL: To configure URL, If HTTP action is chosen. Action Delay: To configure after how long to execute to send out Figure 4.4.3.3 Input interface trigger action notifications and trigger relay. Open Relay: To configure which relay to trigger. 4.4.3.4. Motion Triggered Action Go to Intercom - Motion to configure.
R26B Admin Guide Go to Phone - Action URL, pick Active to be “Enabled”, pick to demand triggered incident, each “HTTP” request to have to including the key and value, use“=” to separate，each value staring with “$.” For example, “Open Relay Success” incident, input http://server IP address/help.xml?mac=$mac, when the relay of R26B is triggered successfully, the phone will send a HTTP packet to the server, through the HTTP package to know the MAC of the Figure 4.4.3.5 Action URL phone. 4.5. Upgrade 4.5.
R26B Admin Guide 4.5.2. Autop Upgrade Go to Upgrade - Advanced to configure automatically update server’s settings. Figure 4.5.2-1 Autop update PNP Option Plug and Play, once PNP is enabled, the phone will send SIP subscription message to PNP server automatically to get auto provisioning server’s address. By default, this SIP message is sent to multicast address 224.0.1.75 (PNP server address by standard). Figure 4.5.
R26B Admin Guide configuration more easily. This is a typical C/S architecture upgrade mode, mainly by the terminal device or PBX server to initiate an upgrade request. URL: Auto provisioning server address. User Name: Configure if server needs an username to access, otherwise left blank. Password: Configure if server needs a password to access, otherwise left blank. Common AES Key: Used for phone to decipher common auto provisioning configuration file.
R26B Admin Guide This auto provisioning mode is actually self-explanatory. For example, mode ”Power on” means phone will go to do provisioning every time it powers on. Note: Please refer to the related feature guide from Akuvox forum. 4.5.3. Backup Config File Figure 4.5.3-1 Backup config file Go to Upgrade - Advanced to backup the config file. Export Autop Template: To export current config file. Others: To export current config file (Encrypted) or import new config file. Figure 4.5.
R26B Admin Guide Note: To make DHCP autop URL works, the PNP should be disable. 4.6. Log Figure 4.6.1 Call log 4.6.1. Call log Go to Phone - Call Log, users can see a list of call log which have dialed, received or missed. Users can delete calls from list. 4.6.2. Door Log Go to Phone - Door Log, users can see a list of door log which records card information and data. 4.6.3. System Log Figure 4.6.2 Door log Go to Upgrade - Advanced to configure system log level and export system log file.
R26B Admin Guide System log level: From level from 0 to 7.The higher level means the more specific system log is saved to a temporary file. By default, it’s level 3. Export Log: Click to export temporary system log file to local PC. Figure 4.6.3 System log 4.6.4. PCAP Go to Upgrade - Advanced to start, stop packets capturing or to export captured packet file. Start: To start capturing all the packets file sent or received from phone. Stop: To stop capturing packets. 44 Figure 4.6.
R26B Admin Guide Abbreviations ACS:Auto Configuration Server DNS-SRV:Service record in the Domain Name System Auto:Automatically FTP: File Transfer Protocol AEC:Configurable Acoustic and Line Echo Cancelers GND: Ground ACD:Automatic Call Distribution HTTP: Hypertext Transfer Protocol Autop:Automatical Provisioning HTTPS: Hypertext Transfer Protocol Secure AES:Advanced Encryption Standard IP: Internet Protocol BLF:Busy Lamp Field ID: Identification COM:Common IR: Infrared CPE:Customer Premi
R26B Admin Guide PCAP: Packet Capture SIP: Session Initiation Protocol PNP: Plug and Play SNMP: Simple Network Management Protocol RFID: Radio Frequency Identification STUN: Session Traversal Utilities for NAT RTP: Real-time Transport Protocol SNMP: Simple Mail Transfer Protocol RTSP: Real Time Streaming Protocol SDMC: SIP Devices Management Center MPEG: Moving Picture Experts Group TR069: Technical Report069 MWI: Message Waiting Indicator TCP: Transmission Control Protocol NO: Normal Opened
R26B Admin Guide Contact us For more information about the product, please visit us atwww.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: techsupport@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products.
