R29 Series Door Phone Admin Guide
About This Manual Thank you for choosing Akuvox‟s R29 series door phone. This manual is intended for end users who need to properly configure the door phone. This manual is applicable to 29.30.2.13 version, and it provides all functions‟ configurations of R29 series door phone. Please visit Akuvox forum or consult technical support for any new information or latest firmware. Note: Please refer to universal abbreviation form in the end of manual when meet any abbreviation letter.
Content 1. Product Overview ............................................................................................................................................................................................................... 1 1.1. Instruction ................................................................................................................................................................................................................ 1 1.2. Connector Introduction ..................
3.3.2. Modify the Web Password........................................................................................................................................................................... 12 3.4. Phone configuration ............................................................................................................................................................................................... 12 3.4.1. Language........................................................................
3.5.1. Phonebook in devices ................................................................................................................................................................................. 27 3.5.2. Phonebook in website ................................................................................................................................................................................. 28 3.5.3. Import/Export contacts ................................................................
3.8.2. Unlock via RFID Cards ................................................................................................................................................................................ 47 3.8.2.1. RFID Cards in Devices ..................................................................................................................................................................... 47 3.8.2.2. RFID Cards in Website ........................................................................
4.2. Intercom ................................................................................................................................................................................................................. 66 4.2.1. Call Time Related ........................................................................................................................................................................................ 66 4.2.1.1. RTP timeout ...................................................
4.4.3. Action ........................................................................................................................................................................................................... 81 4.4.3.1. Email Notification .............................................................................................................................................................................. 81 4.4.3.2. FTP Notification............................................................
R29C-L Admin Guide 1. Product Overview Color camera Microphone 1.1. Instruction Built-in light sensor & infrared sensor Infrared LEDs R29 series is an Android-based IP video door phone with a touch screen. It incorporates audio and video communications, access Touch screen control and video surveillance. Its finely-tuned Android OS allows for feature customization to better suit the habit of usage of local people.
R29C-L Admin Guide 1.2. Connector Introduction Ethernet : Ethernet (POE) connector which can provide both power and network connection.（Note:R29C-L not support PoE function.） 12V/GND: External power supply terminal. WG_D0/1: Wiegand terminal for wiegand access control. RS485A/B: RS485 terminal for automation system control (e.g. Figure 1.2-1 Connection introduction Elevator control). DOORA/B/C: Trigger signal input terminal (e.g. Press indoor button to open relay).
R29C-L Admin Guide 2. Daily use 2.1. Starting When booting R29C-L first time, users need to choose a suitable display language for device. Tap Start to start the selection. R29C-L support 4 languages, including French, English, Spanish and Chinese. Then choosing the proper display theme according to specific application scenarios. R29 supports 3 themes, including Figure 2.1.1-1 Starting Figure 2.1.1-2 Language selection Villa, Building and Office.
R29C-L Admin Guide 2.2. Make a Call There are three ways to make a call from the door phone to monitor units, which can be an indoor monitor or an intercom app. 2.2.1. Call From Digital Keypad Press Dial (Building theme) or Call (Villa theme or Office theme) to enter the dial interface. Enter the number to call on the digital keypad, and press the dial icon. Figure 2.2.1-1 Dial interface (Building theme) 4 Figure 2.2.
R29C-L Admin Guide 2.2.2. Call From Phonebook Tap Contacts to enter the phonebook. In the phonebook interface, to find a specific occupant, scroll up or down the pre-imported contact list, which is either a room number, an occupant‟s name, or the combination of both. It also supports searching the list by alphabet and then clicking the dial key next to the found contact. Figure 2.2.2-1 Phonebook interface Figure 2.2.2-2 Phonebook interface (Building theme) (Villa theme) Figure 2.2.
R29C-L Admin Guide 2.2.3. Call From Speed Dial 2.2.3.1. Building theme Press Reception to make the call directly. 2.2.3.2. Villa theme or Office theme Press Call to enter the call interface, choose a speed dial number that users want to call directly. Figure 2.2.3.1 Reception 2.3. Receive a Call When a monitor unit calls the door phone, it will auto answer the incoming call by default. There is no need to press any answer key. 6 Figure 2.2.3.
R29C-L Admin Guide 2.4. Unlock 2.4.1. Unlock by PIN Codes Unlock the door by using predefined public pin or private pin. Press PIN icon to enter the PIN code interface, enter the “PIN code” and press Confirm icon to unlock, then you will hear “Welcome, please coming” along with the notification “Opening door succeeded”. If users input the wrong PIN code, the screen will shows “Invalid password”. Figure 2.4.1-1 Unlock by pin code (Building theme) 7 Figure 2.4.
R29C-L Admin Guide 2.4.2. Unlock by Face Stand in front of the camera of R29C-L in 0.5-1m and look at the camera, the device will recognize the predefined face less than 0.6s in the main interface(Building theme) or enter the “Password”(Villa or office theme) interface and it will announce “Welcome, please come in” along with the notification “Opening door succeeded”. Otherwise the screen will show “ Opening Door Failed ! ” . The device must be in idle.
R29C-L Admin Guide succeeded”. If the card has not been registered, the phone will show “Invalid password”. 2.4.4. Unlock by DTMF codes During the calling, the president can press the predefined DTMF codes to remote unlock the door. Figure 3.1-1 Access the system setting (Building theme) 3. Basic Features Figure 3.1-2 Access the system setting (Building theme) 3.1. Access the system setting In the Dial interface, press “9999", “Dial key”, "3888”, “OK” to enter the system setting.
R29C-L Admin Guide 3.2. Access the website setting 3.2.1. Obtain IP Address R29 series use DHCP IP by default. Enter the phone interface and go to Info to check the IP address. 3.2.2. Access the Device Website Open a web browser, and access the corresponding IP address. Enter the default user name and password to login. The default Figure 3.2.1 Info administrator‟s user name and password are shown below: User Name: admin Password: admin Note: The recommended browser is Google Chrome. Figure 3.2.
R29C-L Admin Guide 3.3. Password Modification 3.3.1. Modify the Phone System Password Users can configure project key with this function. The public key is a password used by all occupants in a building. Project key is used by administrators for some basic settings. There are two ways to change the system password, which can be done on the phone system and on the intercom website. In the phone interface, go to the Password - Project Passwd to change the project key passwd.
R29C-L Admin Guide 3.3.2. Modify the Web Password Login to the website and go to the path Security - Basic, to modify password for “admin” or “user” account. Figure 3.3.2 Modify the web password 3.4. Phone configuration 3.4.1. Language 3.4.1.1. Modify the phone language In the phone interface, go to Language to configure. Now R29 series can support multiple phone language. Users can choose manually. Akuvox uses English by default. Figure 3.4.1.1-1 Configure phone Figure 3.4.1.
R29C-L Admin Guide Key/Display - Language Setting Of The Building Theme to configure the display language bar. Users can choose the phone language directly from the main interface. Users can also modify the phone language on the portal Phone Figure 3.4.1.1-4 Configure Web Language Time/Lang - LCD Language. 3.4.1.2. Modify the web language Enter the intercom website and go to the path Phone - Time/lang Web Language to configure. Now R29 series can support multiple web language.
R29C-L Admin Guide 3.4.2. Time In the phone interface, go to Time to configure. Choose automatic date & time setting for automatic access of time, date and time zone. Or set the time, date and time zone manually. Users can also set the time zone configuration on the device portal Phone - Time/Lang. Figure 3.4.2-1 Time Figure 3.4.
R29C-L Admin Guide 3.4.3. Network In the phone interface, go to Address or login to the website and go to the path Network - Basic, dynamically or statically to obtain address. 3.4.3.1. DHCP Mode R29 series uses DHCP mode by default which will get IP address, subnet mask, default gateway and DNS server address from DHCP Figure 3.4.3.1-1 DHCP mode server automatically. Figure 3.4.3.
R29C-L Admin Guide 3.4.3.2. Static Mode If select static IP, users should manually setup IP address, subnet mask, default gateway and DNS server address. The figure right shows static IP setting. Figure 3.4.3.2-1 Static mode Figure 3.4.3.
R29C-L Admin Guide 3.4.3.3. Local RTP Go to Network - Advanced to configure. Local RTP: To display and configure local RTP settings. Starting RTP Port: Determine the minimum port that RTP stream can use. Figure 3.4.3.3. Local RTP Max RTP Port: Determine the maximum port that RTP stream can use. 3.4.3.4. Connect Setting Go to Network - Advanced to configure. Connect Type: Display the device connection type, there are three modes, Discovery, SDMC, Cloud.
R29C-L Admin Guide Device Location: Used to identify the device location, which will also serve as the device display name 3.4.3.5. LTE configuration LTE connection serves as a wireless network connection for the device in addition to the wired connection, which is convenient for a quick installation for its wireless feature. You Click LTE icon on home screen and go to Cellular Network Screen to do the configuration.
R29C-L Admin Guide in the same time. 3.4.4. Display 3.4.4.1. Await In the phone interface, go to Await or login to the website and go to the path Intercom - Advanced - StandBy, to set the standby mode, standby time and unlock mode. Standby Mode: There are three options for the standby mode.
R29C-L Admin Guide 3.4.4.2. Upload ScreenSaver In the website and go to the path Phone - Import/Export - Upload screensaver to configure. To upload screen saver and set the corresponding interval time and the priority. It will be displayed on Figure 3.4.4.2-1 Upload ScreenSaver screen when R29 series stand by type as picture. Up to 5 different screen savers can be supported. These pictures will scroll to display. The format must be .jpg. If the interval time is 0, it won‟t be displayed. Figure 3.4.4.
R29C-L Admin Guide manually setup the Interval time which means how long the image will display then change to next screensaver. Interval range from 5s to 120s. Click the Submit to save each one. Click Delete to remove the picture. 3.4.4.3. Theme selection Figure 3.4.4.2-3 Upload ScreenSaver Go to the path Intercom - Key/Display. To choose the device display theme, which supports Villa, Building and Office. 3.4.4.4. Door Setting General Figure 3.4.4.
R29C-L Admin Guide 3.4.4.5. Home View Visible Control (Villa theme) In the website and go to the path Intercom - Key/Display - View Visible of The Villa Theme to configure. Users can setup the home page‟s default display interface, whether the home page-dial interface, contact interface, unlock interface is visible. For example, if users enable dialview, users will only see dialing interface , the other two will be hided. Display Type: Setup the home page‟s default display interface.
R29C-L Admin Guide 3.4.4.6. Key In Homepage of The Building Theme On the device homepage of the building theme, six icon are displayed. Users can configure their type on the website, go to Intercom - Key/Display. Users can customize the feature of the icon. Name: To customize the icon display name; Type: Select the function available for the icon on the device homepage. “NULL” means that the icon is not displayed. Figure 3.4.4.4.
R29C-L Admin Guide 3.4.5. Volume 3.4.5.1. Volume related in device In the phone interface, go to Volume, to configure the call volume, AD volume and key volume. Call Volume: When R29 series dials out a call, it will prompt the „du‟ sound. To configure the call volume by yourself. AD Volume: When the door is opened, the phone will announce the opendoor tone. To configure the AD volume by yourself. Key Volume: When touch the screen, that will be a prompt Figure 3.4.5.1 Phone volume sound.
R29C-L Admin Guide interface. 3.4.5.3. Mic volume in website Mic Volume: Login to the website and go to the path Phone - Figure 3.4.5.3 Mic volume Voice, to configure Mic volume. 3.4.5.4. Open door tone Open Door Tone: Users can also go to the path Intercom - Door Setting General to configure the switch whether users will hear the “Welcome! Please coming” announcement.when the door is Figure 3.4.5.4-1 Open door warning opened.
R29C-L Admin Guide yourself. 3.4.6. DND DND allows IP phones to ignore any incoming calls. Users can login to the website and go to Phone - Call Feature to configure. Return Code when DND: Determine what response code should be sent back to server when there is an incoming call if DND on. DND On Code: The code used to turn on DND on server‟s side, if configured, IP phone will send a SIP message to server to turn on DND on server side if user press DND when DND is off.
R29C-L Admin Guide 3.5. Phonebook 3.5.1. Phonebook in devices In the phone interface, go to Contact to configure the phonebook. Create a group: Choose group, click Add to enter the new group name. Press Save to save. Edit a group: Choose the existed group to modify or delete. Create a contact: Click Add to enter the contact‟s information. Figure 3.5.1-1 Adding group Figure 3.5.1-2 Editing group Figure 3.5.1-3 Adding contact Figure 3.5.
R29C-L Admin Guide 3.5.2. Phonebook in website In the website, go to the path Phonebook - Local Book to configure the phonebook. Figure 3.5-5 Phonebook Contact: To display or edit all local contacts. Search: Enter the key word to search designated contacts from local phonebook. Contact Setting: Choose a suitable contact picture, then import (optional);Enter the corresponding contact name and phone number; Click Add to save. Figure 3.5-6 Contact setting Note: The photo only supports .jpg format.
R29C-L Admin Guide 3.5.3. Import/Export contacts Users can also login to the website and go to the path Phone Import/Export - Import/Export Config&Contacts to upload or download the contact information. Figure 3.5-8 Import/Export contacts Contact: Click Export to export the existed contact. Choose the local file and click Import to import the new contact. The export format is .vcf, the import format is .vcf, .csv or .xml. The import maximum is 3000. 3.5.4.
R29C-L Admin Guide picture or not. Expend Contact List View Mode: With this enabled, the contact list will be displayed in view mode. Hide Group Label For Contact List: With this enabled, the contact list will be displayed directly and there will be no group. Login to the website and go to the path Phonebook - Phonebook Contact List Setting. Show contacts of local group: To enable/disable whether to display the contact list for local groups.
R29C-L Admin Guide code” means that the contact list will be displayed in order of 0~9, a~z; “Room number” means that the contact list will be displayed in order of a~z, 0~9; “Import” means that the contact list will be displayed in the same order as in the import file. 3.6. Intercom call 3.6.1. IP Direct Call In the dial interface. Enter the number to call on the digital keypad, and tap the dial icon. Without SIP server, users can also use IP address to call each other.
R29C-L Admin Guide 3.6.2. SIP Call SIP call uses SIP number to call each other which should be supported by SIP server. Users need to register an account and fill some SIP feature parameters before using SIP call. Login to the website and go to the path Account - Basic to configure SIP account and SIP server for door phone first. 3.6.2.1. Account R29 series supports 2 accounts. According to your needs, register one or two accounts and users can switch them by themselves.
R29C-L Admin Guide 3.6.2.2. SIP Account In the phone interface, go to Account - Account setting Account 1&2 to configure the SIP account. Enable Account: SIP account is only available if you enable this account. Register Name: To enter extension number you want and the number is allocated by SIP server. User Name: To enter user name of the extension. Password: To enter password for the extension. Figure 3.6.2.2-1 SIP account Display Name: To configure name sent to the other call party for displaying.
R29C-L Admin Guide Login to the website and go to the path Account - Basic - SIP Account to configure the SIP account. Status: To display register result. Account: Select the SIP account you need to configure. Account Active: SIP account is only available if users enable this account. Display Label: To configure label displayed on the phone‟s LCD screen. Display Name: To configure name sent to the other call party for displaying.
R29C-L Admin Guide 3.6.2.3. SIP Server In the phone interface, go to Account - Account setting Account 1&2 to configure the SIP server. Users can also go to the path Account - Basic - SIP Server 1&2 to configure. Figure 3.6.2.3-1 SIP server Server IP: To enter SIP server‟s IP address or URL. Server Port: To enter the SIP server port. Registration Period: The registration will expire after registration period, the IP phone will re-register automatically within registration period. 3.6.2.4. Figure 3.6.
R29C-L Admin Guide 3.6.2.5. Transport Type To display and configure transport type for SIP message UDP: UDP is an unreliable but very efficient transport layer protocol. TCP: Reliable but less-efficient transport layer protocol. Figure 3.6.2.5 Transport type TLS: Secured and Reliable transport layer protocol. DNS-SRV: DNS record for specifying the location of services. 3.6.3.
R29C-L Admin Guide supports a prefix number replace 5 number at the same time, when the user press the prefix number, the 5 devices will ring at the same time. Users can edit or delete the exited replace rules. For example: Users can pre-configure 101 to replace 192.168.16.112 and Figure 3.6.3-2 Dial plan 192.168.16.158 in the doorphone. Then, by pressing 101, the two devices can be dialed at the same time through the default account without having to remember the long phone number or dial separately.
R29C-L Admin Guide 3.6.4. Quick Dial Quick dial is to call predefined important number quickly in main interface. This number is often set as emergency number. In the phone interface, go to Quick Dial, switch the type as quick dial, enter the quick dial name and number, click Save to confirm. 3.6.5. Speed Dial The speed dial contact list will be displayed in the dial interface, Figure 3.6.4-1 Quick dial configure Figure 3.6.4-2 Quick dial convenient for users to dial directly.
R29C-L Admin Guide Standard Auto 1/8/16/64 Key 1 Key+Keypad 2 Keys+Keypad 4 Keys+Keypad It will not displayed the contact list, only display time and keypad. The dial interface will based on the number of speed dial contacts. Null displays the time and keypad; 1~4 contacts will displays contacts and keypad; More then 4 contacts, only contacts will be displayed. The dial interface will display the speed dial contacts based on the number of keys, and the keypad will not be displayed.
R29C-L Admin Guide 3.6.6. Auto Answer Login to the website and go to the path Account - Advanced - Call - Auto Answer to enable the auto answer. Figure 3.6.5 -1Auto answer Login to the website and go to the path Phone - Call Feature Others to configure the auto answer related function. Return Code When Refuse: Allow users to assign specific code as return code to SIP server when an incoming call is rejected. Auto Answer Mode: To choose video or audio mode for auto Figure 3.6.5 -2 Auto answer answer. 3.
R29C-L Admin Guide Note: This feature should work with Akuvox Cloud. Please contact your administrator for more information. 3.6.8. Web Call Login to the website and go to the path Phonebook - Local Book Dial to dial out from website. Figure 3.6.6 Web call Dial: To dial out a call or hangup an ongoing call from website.
R29C-L Admin Guide 3.7. Security 3.7.1. Mjpeg Service Login to the website and go to the path Intercom - Advanced Mjpeg Server to configure. Mjpeg Service Enable: Use to capture from the URL. It is Figure 3.7.1 Mjpeg service convenient to check the capture remotely. Image Quality: To choose the image quality of the capture. Picture URL: http:// device ip:8080/picture.cgi http://device ip:8080/picture.jpg http://device ip:8080/jpeg.cgi 3.7.2.
R29C-L Admin Guide check the real-time picture via URL: http://IP_address:8080/video.cgi 3.7.3. RTSP RTSP Basic R29 series support RTSP stream, enter the phone system, go to RTSP or login to the website and go to the path Intercom - RTSP, to enable or disable RTSP server. The URL for RTSP stream is: rtsp://IP_address/live/ch00_0 H.264 Video Parameters Figure 3.7.3-1 RTSP H.264 is a video stream compression standard. Different from H.
R29C-L Admin Guide 3.7.4. ONVIF R29 series supports ONVIF protocol, which means R29 series camera can be searched by other devices, like NVR, which supports ONVIF protocol as well. Go to the path Intercom - ONVIF on the web GUI, to configure ONVIF mode and its username/password. Switching ONVIF mode to “undiscoverable” means that Users must program ONVIF‟s URL manually. The ONVIF‟s URL is: http://IP_address:8090/onvif/device_service 44 Figure 3.7.
R29C-L Admin Guide 3.8. Access Control 3.8.1. Relay Login to the website and go to the path Intercom - Relay to configure. Relay ID: R29 series supports three relays. Users can configure them respectively. Trigger Delay: To configure the duration of the trigger relay. With the trigger condition, the relay will only be triggered if the value is reached. Hold Delay: To configure the duration of opened relay. Over the value, the relay would be closed again.
R29C-L Admin Guide Relay Status: While the relay is triggered, the statues will be switched. When COM connects to NC, the status is Low. Note: Relay operate a switch and does not deliver power, so users should prepare power adapter for external devices which connects to relay. Figure 3.8.1.1-1 Unlock options 3.8.1.1. Unlock Options Users can choose which relay want to opened. On the path Intercom - Relay - Unlock Options, configure to be “VISIBLE”.
R29C-L Admin Guide 3.8.2. Unlock via RFID Cards 3.8.2.1. RFID Cards in Devices R29 series can be compatible with 13.56MHZ and 125KHZ RFID cards. Add Press “Add Card”, when you see “Please scan the RFCard to Add”, put the card near the card sensor. Then enter the device name , valid day and time in the modify prompt. Click OK to save. Modify Figure 3.8.2.
R29C-L Admin Guide 3.8.2.2. RFID Cards in Website Go to the path Intercom - Card setting, to manage RFID cards access system. Import/Export Card Data: Export the existed RFID cards Figure 3.8.2-3 Import/Export card data information or import the new RFID cards information. It can only support .xml format. The maximum is 1000. Note: Ask your administrator for the card data template if you need. Obtain and Add Card: Figure 3.8.
R29C-L Admin Guide Door Card Management: Valid card information will be shown in the list. Administrator could delete one card‟s access permission or empty all the list. Note: Remember to set card status back to normal after adding the cards. Figure 3.8.2-6 Door card management 3.8.2.3. Card Type Support Go to the path Intercom - Card Setting, to choose the type of card you need. Users can choose enable the NFC or Felica.
R29C-L Admin Guide 3.8.3. Unlock via Pin Codes 3.8.3.1. Private Pin Codes in Device In the phone interface, go to LockPasswd, enter the owner name, 8 digits private keys and Device (optional). Setup the valid day and time for the password. For example: Owner name is Eve, private key is 1995, and I set up the valid day from Mon to Sun, click Save to save. Figure 3.8.3.1-1Adding private key 3.8.3.2. Figure 3.8.3.
R29C-L Admin Guide Obtain and Add Code: (1)Enter the “PKey Name” and “PKey Code”; (2)Select the valid day and time; (3)Choose which door users want to open; (4)Click “Add” to add it into list. Private Key Management: Figure 3.8.3.2-2 Private key setting Valid private key information will be shown in the list. Administrator could delete private key information or empty all the list. Figure 3.8.3.
R29C-L Admin Guide 3.8.3.3. Public Pin Codes in device In the phone interface, go to Password - Public Key Passwd, enter the old public key, R29 series support 3 default public keys. Then enter the new password, after entering the new password Confirm, click save icon. Note: Just need to enable public key password in public key password setting. 3.8.3.4. Public Pin Codes in websites Go to the path Intercom - Basic - Password. Users can configure Figure 3.8.3.
R29C-L Admin Guide 3.8.4. Unlock via Face 3.8.4.1. Face in Device Comparing with the previous access method, face recognition is so convenient.that user do not need to remember the pin code or take a card. Enter device access system, click Face in the last page to do face registration and modification. Register: Please enter the face registration name and click “Register” to save the user information. Then stand in front of the camera of R29 0.
R29C-L Admin Guide upgrading. Modify: Click Face database, choose the existed database to delete 3.8.4.2. Face in Website Click Intercom-Face-Face Basic on the device web interface to configure the face parameters and information. Face Recognition: Click Enable to turn on the face recognition feature. This option is enabled by default. Offline Learning: The device will compare with the existed face data via scanning face every time. Then automatically learning and improving your face characteristic.
R29C-L Admin Guide Recognize Option: : It is divided into 4 levels -Low, Normal, High or Highest. The higher level, the lower error recognition rate without live detection. Antispoofing Option: It is divided into 4 levels -Low, Normal, High or Highest. The higher level, the lower error recognition rate with live detection. Facial recognition Interval: The interval between the two face recognitions. The maximum interval time is 8s.
R29C-L Admin Guide Tips When Succeed: You can click to select “Default” door unlock success notification “Opening Door Succeeded” or you can click “Resident Name” to change the notification to the names registered for the facial recognition. Face Setting Lift Floor Number: Combining the face data with the corresponding floor, face data should belong to an existing contact , so the name of face must be same with the corresponding contact. Figure 3.8.4.
R29C-L Admin Guide Import/Export file: Because R29 series can not support the third party camera to enter the face picture now. Users need to directly retrieve face data in the R29 series, then export them the existing Figure 3.8.4.2-5 Face import/export face file. It is convenient to share the same face data in multiple devices. 3.8.5. Unlock via QR code On the portal Intercom - Relay - Open Relay via QR. Enable the QR function. Note: This function should be work with Akuvox cloud. For more Figure 3.8.
R29C-L Admin Guide BLE Mode: To configure the BLE mode. Rssi Threshold: Set the threshold of received signal strength indicator. The smaller absolute value ,the higher sensitivity. Delay: To configure the duration of opened relay. Over the value, the relay would be closed again. Note: This function needs to be used with Akuvox cloud, please contact your administrator for more information. 3.8.7.
R29C-L Admin Guide Finger Key Management: Valid finger key information will be shown in the list. Administrator could delete finger key information or empty all the list. Figure 3.8.7-2 Finger key management 3.8.8. Unlock via HTTP Command Login to the website and go to the path Intercom - Relay - Open Relay via HTTP to configure. Users can use a URL to remotely unlock the door. It is more convenient for users to open the door if users are not beside the devices. Figure 3.8.
R29C-L Admin Guide 3.8.9. Unlock via Exit Button R29 series supports 3 input triggers Input A/B/C (DOORA/B/C). Login to the website and go to the path Intercom - Input to configure. Figure 3.8.9 Input Input Service: To enable or disable input trigger service. Trigger Option: To choose open circuit trigger or closed circuit trigger. “Low” means that connection between door terminal and GND is closed, while “High” means the connection is opened. Door Status: To show the status of input signal. 3.8.10.
R29C-L Admin Guide triggered. Note: This feature is often to trigger the signal via relay terminal. 3.9. Reboot In the phone interface, go to Reboot to click the Reboot, or go to the path Upgrade - Basic on the web GUI, click Submit, the device will restart. Figure 3.9-1 Reboot Figure 3.
R29C-L Admin Guide 3.10. Reset In the phone interface, go to Restore. Click Restore, if users sure to restore to factory settings, please choose Confirm in the prompt window. Users can also login to the website and go to the path Upgrade Basic, directly click Submit to reset R29 series. Use this function with caution. All configuration will be removed. Figure 3.10-1 Restore Figure 3.
R29C-L Admin Guide 4. Advanced Features 4.1. Phone Configuration 4.1.1. IR LED The setting is for night vision, when the surrounding of R29 series is very dark, infrared LED will turn on and R29 series will turn to night mode to let the users see video clearly from the R29. In the phone interface, go to LED or go to the path Intercom Advanced - LED on web GUI, to configure the IR LED function. Led Type: It can supports four modes - OFF, ON, AUTO ， SCHEDULE. Figure 4.1.
R29C-L Admin Guide current intensity or user can setup the value manually. Once the environment intensity is darker than the predefined threshold value, LED will be up. Min/Max photoresistor: Photoresistor value relates to light intensity and larger value mean that light intensity is smaller. When photoresistor value is greater than max value, LED will turn on. In contrast, when photoresistor value is less than min value, infrared LED will turn off and the device turns to normal mode.
R29C-L Admin Guide 4.1.2. LED of Display Login to the website and go to the path Intercom - LED Setting LED Control to configure. Card LED Enable: To control the LED of the card reader area. Start Time (H): Setup the LED light up time. According to the system time. For example 18-23 means the LED will continuously Figure 4.1.2 LED control light up from 6:00pm to 11:00pm. 4.1.3.
R29C-L Admin Guide backlight. There are two types for users, Auto and Manual. 4.1.4. RFID Card Code Display Related Login to the website and go to the path Intercom - Advanced RFID to configure. Display Mode: To be compatible different card number formats in Figure 4.1.4 RFID different systems. The default 8HN means hexadecimal. 4.2. Intercom 4.2.1. Call Time Related 4.2.1.1. RTP timeout RTP Timeout: Login to the website and go to the path Intercom 66 Figure 4.2.1.
R29C-L Admin Guide Basic - Door Setting General to configure. This feature is specially designed for R47P. When R47P auto answer in mute status, if over the configured time R29 series did not receive the RTP message, R29 series will hang up automatically. 4.2.1.2. Max call time Max Call Time: Login to the website and go to the path Intercom Basic - Max Call Time to configure the max call time. 4.2.1.3. Figure 4.2.1.
R29C-L Admin Guide 4.2.1.4. Hang up after open door Login to the website and go to the path Intercom - Basic - Hang Up After Open Door. Figure 4.2.1.4 time our Time Out: When the callee press the DTMF code to open the door, this call will hang up automatically after the timeout. 4.2.2. Return Code When Refused Login to the website and go to Phone - Call Feature - Others to configure. Figure 4.2.
R29C-L Admin Guide designated SIP account. Min Local SIP Port: To configure minimum local SIP port for designated SIP account. Caller ID Header: To choose caller ID header format automatically. Anonymous Call: If enabled, R29 series will block its information when calling out. Anonymous Call Rejection: If enabled, calls who block their information will be screened out. Missed Call Log: If enabled, any missed call will be recorded into Figure 4.2.3 SIP call related call log.
R29C-L Admin Guide new incoming call when there is already an active call. Call Waiting Tone: If enabled, it allows IP phones to play the call waiting tone to the waiting callee. On Code: The code used to enable call waiting on server‟s side, if configured, IP phone will send a SIP message to server to turn on call waiting on server side if user setup calls waiting is disabled.
R29C-L Admin Guide 4.2.6. Codec Login to the website and go to the path Account - Advanced to Figure 4.2.6-1 SIP account configure the video codec and audio codec. Audio Codec Sip Account: To choose which account to configure. Audio Codec: R29 series supports four audio codec: PCMA, PCMU, G729, G722. Different audio codec requires different bandwidth, user can enable/disable them according to different network environment. Note: Bandwidth consumption and sample rates.
R29C-L Admin Guide Video Codec R29 series supports H264 standard, which provides better video quality at substantially lower bit rates than previous standards. Codec Resolution: R29 series supports four resolutions: QCIF, CIF, VGA, 4CIF and 720P. Codec Bitrate: To configure bit rates of video stream. Codec Payload: To configure RTP audio video profile Figure 4.2.6-3 Video codec 4.2.7.
R29C-L Admin Guide 4.2.8. Session Timer Go to the path Account - Advanced - Session Timer on the web GUI to configure. If enabled, the on going call will be disconnected automatically once the session expired unless it‟s been refreshed Figure 4.2.8 Session timer by UAC or UAS. 4.2.9. NAT Login to the website and go to the path Account - Advanced NAT to configure. UDP Keep Alive Messages: The phone will send UDP keep-alive message periodically to router to keep NAT port alive. Figure 4.2.
R29C-L Admin Guide 4.2.10. User Agent Login to the website and go to the path Account - Advanced User Agent to configure. User Agent: One can customize users agent field in the SIP Figure 4.2.10 User Agent message; if user agent is set to specific value, users can see the information from PCAP. If user agent is not set by default, users can see the company name, model number and firmware version from PCAP. 4.2.11.
R29C-L Admin Guide Basic, Digets, Token. No authentication is required for http api, it is only used None by demo testing. Username/Password: Used in basic and digest auth mode. The default username/password is admin/httpapi. Normal (reserved) The whitelist is suitable for operation in the LAN, by IP01~05: Configure the white list IP. WhiteList judging the IP address of the visitor to confirm whether to allow access to the HTTP API.
R29C-L Admin Guide 4.3. Access control 4.3.1. Webrelay R29 series supports extra web relay. This function is more safety to use DTMF code to remote unlock. Login to the website and go to the path Phone - Web Relay to configure. Figure 4.3.1-1 Web relay Web Relay Type: Connect web relay and choose the type. IP Address: Enter web relay IP address. User Name: It is an authentication for connecting web relay. password: It is an authentication for connecting web relay.
R29C-L Admin Guide relay will be open with local relay. But if there are different, the web relay is invalid. Web Relay Extension: The webrelay can only receive the DTMF signal from the corresponding extension number. 4.3.2. Wiegand Login to the website and go to the path Intercom - Advanced Wiegand to configure. Wiegand Type: Support Wiegand 26,34,58. The different number means different bits. Wiegand Mode: Input or output.
R29C-L Admin Guide Wiegand Input/Output Order: To make the data from wiegand devices to be normal order or reversed order. Wiegand Output CRC: To be compatible with the other three party wiegand access control which do not use the standard wiegand order, CRC can correct the order format. 4.4. Security 4.4.1. Antialarm of Door Phone 4.4.1.1. Antialarm in device In the phone interface, go to AntiAlarm to configure it. This function is used to trigger the alarm by perceiving the change of gravity.
R29C-L Admin Guide location. The detailed gravity sensor value can be adjusted in website. Tamper Proof Switch: Switch this feature. Tamper Proof Switch: The smaller the value, the more sensitive the gravity sensor is. Tamper Alarm Volume: To configure the tamper alarm volume. 4.4.1.2. Antialarm in website Login to the website and go to the path Intercom - Advanced Tamper Alarm to configure.
R29C-L Admin Guide 4.4.2. Motion 4.4.2.1. Motion in device In the phone interface, go to Motion to configure. By enabling the motion detection function, the door phone will detect and record any change in the surrounding, such as suspicious people loitering around, and send notification message to a monitor unit. Timing setting If users only enable time mode and setup the interval.
R29C-L Admin Guide 4.4.2.2. Motion in website Login to the website and go to the path Intercom - Motion - Motion Detection Options to configure. Enable: To enable or disable motion detection. Timing Interval: R29 series will take the picture in the interval time. Detection Accuracy: The smaller value, the capture picture is more accurate. After you setup motion, to configure the target address where to receive the pictures. 4.4.3.
R29C-L Admin Guide path. It is useful for users to check the capture picture for security. Sender’s email address: To configure email address of sender. Receiver’s email address: To configure email address of receiver. SMTP server address: To configure SMTP server address of sender. SMTP user name: To configure user name of SMTP service (usually it is same with sender‟s email address). SMTP password: To configure password of SMTP service (usually it is same with the password of sender‟s email).
R29C-L Admin Guide FTP Path: Enter the folder name you created in FTP server. 4.4.3.3. Input Interface Triggered Action Go to the path Intercom - Input on the website to configure. Action Delay: To configure after how long to execute to send out Figure 4.4.3.3 Input interface triggered action notifications and trigger relay. Open Relay: To configure which relay to trigger. 4.4.3.4. Reception Action In Building On the path Intercom - Key/Display - Reception Action In Figure 4.4.3.
R29C-L Admin Guide 4.5. Upgrade 4.5.1. Web Update Login to the website and go to the path Upgrade - Basic, users can upgrade firmware. Figure 4.5.1 Web update Upgrade: Choose .zip/.rom firmware from your PC, then click Submit to start update. 4.5.2. Autop Upgrade Login to the website and go to the path Upgrade - Advanced to configure. Manual Autop 84 Figure 4.5.
R29C-L Admin Guide Autop is a centralized and unified upgrade of IP telephone. It is a simple and time-saving configuration for IP phone. It is mainly used by the device to download corresponding configuration document from the server using TFTP / FTP / HTTP / HTTPS network protocol. To achieve the purpose of updating the device configuration, making the user to change the phone configuration more easily.
R29C-L Admin Guide 0c1105888888.cfg if IP phone‟s MAC address is 0c1105888888). Note: AES is one of many encryption, it should be configured only when configure file is ciphered with AES, otherwise left blank. Automatic Autop To display and configure Auto Provisioning mode settings. This Auto Provisioning mode is actually self-explanatory. For example, mode “Power on” means IP phone will go to do Figure 4.5.2-2 Automatic Autop Provisioning every time it powers on.
R29C-L Admin Guide Note: The exported config here is encrypted. Users can also go to the path Phone - Import/Export Import/Export Config&Contact to export or import the config. Click Export to export the config file. 4.6. Log 4.6.1. Call Log Login to the website and go to the path Phonebook - Call Log, users can see a list of call which have dialed, received or missed. And user can delete calls from list. Figure 4.6.
R29C-L Admin Guide 4.6.2. Door Log Login to the website and go to the path Phone - Door Log, users can see a list of door log which records card information and date. 4.6.3. System Log Figure 4.6.2 Door log Go to the path Upgrade - Advanced - System Log on web GUI. To display system log level and export system log file. System Log Level: From level 0 to 7. The higher level means the more specific system log is saved to a temporary file. By default, it‟s level 3.
R29C-L Admin Guide 4.6.4. PCAP Go to the path Upgrade - Advanced - PCAP on web GUI. To start, stop packets capturing or to export captured Packet file. Start: To start capturing all the packets file sent or received from IP Figure 4.6.4 PCAP phone. Stop: To stop capturing packets.
R29C-L Admin Guide Abbreviations ACS: Auto Configuration Server DNS-SRV: Service record in the Domain Name System Auto: Automatically FTP: File Transfer Protocol AEC: Configurable Acoustic and Line Echo Cancelers GND: Ground ACD: Automatic Call Distribution HTTP: Hypertext Transfer Protocol Autop: Automatical Provisioning HTTPS: Hypertext Transfer Protocol Secure AES: Advanced Encryption Standard PCAP: Packet Capture BLF: Busy Lamp Field PNP: Plug and Play COM: Common RFID: Radio Frequency Identi
R29C-L Admin Guide Contact us For more information about the product, please visit us atwww.akuvox.com or feel free to contact us by Sales email: sales@akuvox.com Technical support email: techsupport@akuvox.com Telephone: +86-592-2133061 ext.7694/8162 We highly appreciate your feedback about our products.
FCC Statement: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.
