VP R48G User Manual 1
Content 1 Welcome ................................................................................... 6 2 Product Overview ...................................................................... 8 2.1 Instruction ........................................................................................................ 8 2.2 Technical Specification ..................................................................................... 9 2.3 Equipment Appearance And Interface Description ................
4.7 Call Settings .................................................................................................... 35 4.7.1 Always forwarding & Forwarding Number ......................................... 35 4.7.2 Call forwarding busy & Forwarding Number ...................................... 36 4.7.3 No Answer Forwarding & Forwarding Number .................................. 36 4.7.4 Time out .............................................................................................. 36 4.7.
5.5 Call Return ...................................................................................................... 66 5.6 BLFList ............................................................................................................ 67 5.7 Pickup & Group Pickup ................................................................................... 67 5.8 ACD ................................................................................................................. 68 5.9 Hot Desking ........
6.1.2 Local Update ....................................................................................... 96 6.1.3 Remote Update ................................................................................... 97 6.2 Auto Update Period ....................................................................................... 98 6.3 Upgrade on the web ...................................................................................... 99 6.4 Check Update After System Power On .........................
1 Welcome Thank you for purchasing Akuvox VP-R48G Multimedia VoIP Phone. The VP-R48G is an innovative smart desk phone loaded with tremendous value for business communications as well as unprecedented power for advanced custom business applications development and personalization. Featuring Android 5.1 system, a 7 inch capacitive touch screen TFT LCD, a 1.
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna.
2 Product Overview 2.1 Instruction VP R48G is an Android based multimedia terminal with a 7 inch touch screen and a 1.3M CMOS sensor camera. It supports H.264/H.263 codecs with adaptive bandwidth adjustment. The 7 inch touch screen offers excellent user experiences such as high quality videophone, smooth internet surfing, various Android Apps and daily information. VP R48G provides 2 Ethernet ports, 1USB, 1HDMI, and one 3.5mm headset/audio port.
2.2 Technical Specification Model Graphic Display Camera Network Protocol Operation System VP R48G z 7 inch capacitive touch screen TFT LCD, 1024x600 pixels, 16:9 wide screen aspect ratio z 1.3 mega pixels CMOS camera, free rotation z SIP RFC3261,TCP/UDP/IP,PPPOE,RTP/RTCP z Android 5.1 Voice Codec z G.711A/U, G.729, G.722ē z AMR NB, AMR WB, OPUS Video Codec z H.263, H.
2.
USB HDMI Headset Figure 1 3 R48G Profile View 2.3.1 Interface Description Interface Description Camera USB interface Adjustable camera shooting angle, rotate down the camera to "off" angle. External USB storage device Headset Connect to 3.5mm stereo headphone, headset device HDMI Use HDMI cable to output the video to a TV screen LAN Power Network interface can be connected to a hub, switch or other network access devices. It also supports POE(Power over Ethernet) .
Volume Press + or – for the phone volume adjustment Standard Keypad Input the number or symbol Function Key Delete Delete a character before the cursor OK Same function with soft keyboard "Enter" key Message Optional Contact Enter Into the contacts list, you can view the local contact Conference The first party is held in the case, according to a conference key, the first party can be combined to achieve a tripartite meeting Hold To hold a call during the call Transfer To t
3 Installation 3.1 Equipment Packaging Name Quantity Main Case 1 Handset 1 Phone Cord 1 Power Adapter 1 Ethernet Cable 1 Quick Start Guide 1 3.
z Connecting to Network Use the matched network cable to connect the LAN Port of the video phone to the Router or Switch. Viewing the top right corner of the screen, if the indicator light is on, network cable is connected properly. z Connecting to PC Use the matched network cable to connect the PC Port of the video phone to the PC. The PC can access to the internet network via PC Port of the video phone. 3.
4 Getting Started 4.1 Basic Operation 4.1.1 Main Screen Instruction z Status bar, at the top of the screen, displaying the status of system information. z Shortcuts, at the bottom of the screen, user can drag a shortcut to this region to achieve the replacement of the shortcut. Supports max four shortcuts. 4.1.
Status Area Icon Description Network is connected Slide mode (Sound is off) Alarm clock is set Bluetooth is opened Notification Area Icon Description SIP account is unregistered SIP account is registered Missed call uploading 4.1.3 Using The Touchscreen z Tap To select items on the screen (e.g., setting options, apps); to press onscreen buttons; to type letters and symbols using the onscreen keyboard.
z Slide Move your finger fast across the screen to slide. To view different idle screens or menu pages, slide left or right; to view the status bar on top of the screen, place your finger on the bar and slide it down. If your finger stays on the screen for too long, the item may be selected and sliding won’t occur. z Double click Click on the screen twice in quick succession, for example, when user surfs in browser, you can quickly click twice on the page, the page can be enlarged.
z To turn off notifications, simply drag down the middle of the idle screen to display notifications, click on the icon to clear up the notice. As shown below. 4.2 Connecting To Network And Wi Fi VP R48G supports a variety of network connections (Ethernet, Wireless) and the device Network connections includes three modes, Static IP, DHCP, Wi Fi access. DHCP is the default configuration.
z Mode 2: In the main screen, tap icon > Network Settings > LAN Type >Access Mode >chose Static IP.
DNS Server set the DNS address Alternative DNS Server set the backup DNS address 4.2.2 Configuring DHCP You can select one of the following methods to enter the DHCP configuration interface: z Mode 1: In the main screen, tap icon > Settings > Wireless & Networks >More >Ethernet > Ethernet Ip mode >check dhcp. z Mode 2: In the main screen, tap cion >Network Settings >Network Management >LAN Type >Access Mode > chose DHCP.
4.2.3 Configuring Wi Fi You can select one of the following methods to enter the Wi Fi configuration: z Mode 1: In the main screen, tap icon > Settings > Wireless & Networks > Wi Fi. Configuration page is shown as belowġ z Mode 2: In the main screen, drag down the middle of the idle screen to display notifications > tap icon > tap Wi Fi.
1) When the Wi Fi switch is turned on, the video phone can list and display all Wi Fi AP searched in the environment. 2) When connects to available AP in the environment, if a Wi Fi AP is without password protection, there is no lock icon on Wi Fi signal, it will automatically connect when clicked. 3) If a Wi Fi AP is encryption, Wi Fi signal will be added the lock icon, and when checked, it will pop up a dialog box to enter a password.
IP settings(Static IP): 5) Tap the connected Wi Fi AP, it will pop up a dialog box, you can forget the network or modify the network. Touch and hold on the non connected Wi Fi AP, it will pop up a dialog box, and you can click and connect to network. 6) Click Menu, you can do the operations such as: add network setting, refresh the Wi Fi AP list and Advanced setting.
a. Check Network notification, it will notify you when an open network is available; b. Check Scanning always avaible, let google’s location service and other apps scan for networks, even when Wi Fi is off. c. View the Wi Fi Mac address and IP address; 4.
4.3.1 Add Account Click an account to enter Account Editor interface.
Configuration parameters are described as follows: Parameter Specification Register Name SIP Accout ID provided by ISP User Name SIP User Name provided by ISP Password SIP Password provided by ISP Display Name SIP Display name Reg Server IP SIP Register Server, format: domain/IP, for example: 194.168.1.2 Reg Server Port The default port is 5060. Proxy Server IP SIP Proxy Server, format: domain/IP, for example: 194.168.1.
4.3.2 SIP Account ON/OFF After SIP account is configured and registered successfully, it will display the prompt ”Registered” in the Account Manager, and the icon will be displayed on the status bar. If you want to disable the registered account, tap the icon account status, the icon to change the will be shown on the status bar.
2) Remove the sip account: Click the box of the account which you want to delete, then on the bottom of the account list will display the label “Clear Account”, tap this label to remove the selected account. 4.4 Sound & notification You can select one of the following methods to enter the Sound configuration: z Mode 1: In the main screen, tap shortcut icon > Device > Sound & notification.
Including Volume, Ringtone and Notification. 4.4.1 Volumes In Sound & notification page, the volume configure is shown as belowġ z Volume options include Media, Alarm clock, Notification. z You can directly click a volume location to adjust the volume. z The volume settings, you can also press the keyboard volume button ”+ ” to increase or decrease the 29 volume.
to adjust for ringtone or notification volume, but in the broadcast media, pressing volume button is to adjust for media volume. 4.4.2 Interruptions In the Sound & notification interface, click the Interruptions bar, enter the interruptions setting interface. If the user open the Silent mode, can enter the interruption interface to set priority event or priority time allow interrupt.
4.4.3 Phone ringtone In the Sound & notification interface, click the Phone ringtone bar to pop up default ringtone setting interface. Click the ringtone you want to set, after the selection, it will ring a short time. Finally, click "OK".
4.4.4 Default notification ringtone In the Sound & notification interface, click the Default notification ringtone bar to pop up the phone default notification ringtone setting interface. Click the ringtone you want to set, after the selection, it will ring a short time. Finally, click "OK".Setting interface shown as below. 4.4.
4.6 Video Settings To configure the video corresponding parameters.
34
4.7 Call Settings 4.7.1 Always forwarding & Forwarding Number All the incoming calls will be forwarded unconditionally to specified number.
1. Phone Settings > Call Settings > Call Forwarding > Always Forwarding 2. Select the desired account on the Account bar. 3. Check to enable Always Forwarding feature. 4. Input the forward number into the Forwarding Number bar. 4.7.2 Call forwarding busy & Forwarding Number The incoming calls will be forwarded to specified number when the phone is busy. Configuration on the phone: 1. Phone Settings >Call Settings >Call Forwarding >Call Forwarding Busy 2.
4.7.5 Do Not Disturb DND function is to prevent foreign phone from disturbing, If open DND, external phone call is unable to call in, turned off by default. Configuration on the phone: 1. Phone Settings > Call Settings > Do not Disturb 2. Select the desired account on the Account bar. 3. Check to enable Do not Disturb feature. 4.7.
enable silent mode when auto answer the intercom call and the intercom originator will not hear speaker’s voice. 4.7.9 Hotline Enable the Hotline feature allows the phone to call out a defined number automatically, without input any number by manual in dial up interface. Hotline Delay Time is to set the call out delay value. The range value is 0 to 5 second. 4.8 Dial Plan Rules: Allow user to select Replace Rules or Dial Now to display or edit.
4.9 Auto Provision Phone can be configured to resynchronize its internal configuration state to match a remote profile periodically and on power up by contacting a normal provisioning server (NPS) or an access control server (ACS).
4.10 Personalize 4.10.1 Log Level The Log level is divided into seven levels: EMERG, ALERT, CRIT, ERR, WARNING, NOTICE, INFO, DEBUG, log class is from low to high. The default setting is EMERG, which is the lowest grade log. 4.10.2 Hook Mode Hook Mode is divided into Phone Mode, Disable, App Mode, Auto Mode. The default mode is Phone Mode. 4.11 Reboot Manager 4.11.1 Reboot time User can setup the reboot date and hour you want .
4.11.2 Status of time If the status is enable ,users can edit the reboot time you want. 4.11.3 Status of active Enable/disable the reboot function 4.11.4 Reboot settings Set the reboot time. Disable this feature by default. 4.
If user want to manually set the date and time, firstly, tap Automatic data & time bar to disable status, and then set the date, time, select a time zone. Tap Set date bar to pop up date set interface. As shown below. Tap Set time. Time settings as shown below.
Tap the Use 24 hour format bar to change the hour format displayed, 1:00 PM format by default. Tap the Choose date format bar to pop up the date format selection interface. Month/day/year date format by default. Shown as below.
4.13 Personalization Settings According to personalized settings,user can set the equipment more characteristic. 4.13.1 Wallpaper User can use the following ways to set the favorite wallpaper. Mode 1: In the main screen, Press Menu button on the keyboard > tap WALLPAPERS icon. Mode 2: In the main screen, touch and hold on the blank part of desktop > tap WALLPAPERS icon.
4.13.2.1 Add A Widget User can use the following ways to add the widgets. Mode 1: In the main screen, Press Menu button on the keyboard > tap the WIDGETS icon. Mode 2: In the main screen, touch and hold on the blank part of desktop > tap WIDGETS icon. Each widget has indicated the name and the location, touch and hold to pick up a widget, move it to the designated location on the desktop,then move fingers away from the screen.
can control the white point to drag the border to change the size of the widget frame. And then only need to press Back button on the keyboard to save the change. As shown below: 4.13.2.3 Delete A Widget Touch and hold the widget until the icon the screen, drag the widget to appears on the upper left corner of location until the widget turn red, then move fingers away to delete the widget. 4.13.
4.13.3.2 Modify A Shortcut If user want to modify the location of shortcut on the desktop, hold the shortcut until the icon appears on the upper left corner of the screen, you can drag the shortcut to the corresponding position of the desktop. 4.13.3.3 Delete A Shortcut Touch and hold the shortcut until the icon the screen, drag the shortcut to appears on the upper left corner of location until the shortcut turn red, then move fingers away to delete the shortcut. 4.
notification settings. If user choose the music downloaded from the Internet as a ringtone, please follow the below steps: 1) Click > Music icon . 2) View the music list in App, touch and hold a music, and then In the pop up menu options, click Use as phone ringtone. 4.14 Backup & Reset 1) Click Setting . 2) Personal >Tap Backup & reset. 3) Personal data > click Factory data reset. 4) Check Erase SD card > click RESET DEVICE label > tap ERASE EVERYTHING label.
5 Function 5.1 Call Function R48G phone supports audio calls and video calls. User can use the SIP account to make a call, also can use IP direct make a call. SIP account configuration refers to chapter 4.3 5.1.1 Make A Call User can directly dial from the keypad, select from the contact list or from call records to call out the number. User can choose one of the following steps to enter into the dialing interface.
3) If registered multiple available SIP accounts, when finishing dialing, user can click label to choose the outgoing account for the number, as line shown below. 5.1.2 Dialing Out From Contact List 1) Tap icon 2) Click >Click the icon > Label Phone Book >All Contacts.
click label to send the message. Contact is shown as belowġ 5.1.2.1 Contacts Fuzzy Matching Query Phone supports contacts fuzzy matching queried, intuitive, concise dialing interface for the intelligent input, greatly reducing the number of buttons, achieve rapid, effective positioning search, avoid duplication of invalid operation, saving time. Tap search icon to enter the search interface. Enter the key symbol or number to search the contact.
5.1.3 Receive A Call Incoming calls include audio and video calls. If the caller has been stored in the contacts, it will show the contact name, otherwise the caller number will be displayed. 5.1.3.1 Answer A Call 1) Answer an audio call When receiving an audio call, click Audio label or pick up the handset or press speaker button on the keypad to answer.
5.1.3.2 Reject A Call label in calling interface. If user want to reject a call, click If user want to reject a call from a number, you can add the number to the blacklist. 5.1.4 Call Options During the audio conversation, the default call options shown as below.
Call options are described as below. Click the button to hold the current call. Click the button to resume the current call.
Video options are described as below. Support local and remote video displayed Support remote video displayed Click to open full screen/ exit full screen 5.1.4.1 Multiple Calls z The Phone supports more than 3 line calls. The line information is on the right side of call interface. z During a call, user can click on the icon to add a new call. And when click on this button, the current call will be hold.
5.1.5 Call Records 5.1.5.1 View Call Records When got a missed call, the screen will display the missed call notification in above status bar. User can drag down to open the notification list, then click the missed call notification to view call records. User can also directly through the dialing interface to view call records: 1) In the main screen, click 2) Click icon . Shown as below.
3) User can click the drop down list to choose the call record types, it supports for All Call, Missed Call, Received Call, Dialed Call and Forwarded Call five types of call information. 4) Call records are shown on the left. Click the number or contact, and user can view all the call records details on the right. 5.1.5.
1) Long press the call record you want to delete. 2) Pop up a menu, press Confirm label to confirm the deletion. z To delete multiple call records, steps as below: 1) Press the icon on the top right corner of the screen. 2) Check the records on the left list. . 3) Click icon z To delete all call records, steps as below. 1) Press the icon 2) Tap on the top right corner of the screen. on the bottom left of the screen. . 3) Click icon 5.1.5.
5.2 Contacts Following method to enter into Contacts interface. Enter the dialing interface, and then click the icon .
5.2.1 Local Phone Book User can view, audio call, video call, add, edit, delete the Local contacts. 5.2.1.1 Add A New Contact Click the icon on the top right corner, and click New Contact label in the drop down window.
5.2.1.2 Modify The Contact 1) Select the contact need to modify in the contact list. 2) Click icon . 3) Enter into contact edit page, edit the contact information. 5.2.1.3 Delete The Contact Following methods to delete the contacts. z Touch and hold the contact need to delete from contact list, and tap Confirm label in the pop up Remove Contact dialog box.
further information. 5.2.3 Remote Phone Book Access the remote phone book, add the contacts to the local phone book from the remote phone book or make calls from the remote phone book. 5 URLs of remote phone book is available to set. z Set the remote phone book via web interface. 1) Access Phone Book > Remote Phone Book. 2) Input URL of phone book. 3) Input the phone book name. 4) Click the Submit key to save. z Enter the remote phone book via phone interface.
5.2.5.1 Add A New Group 1) Access contact setting interface > Local Phone Book > tap icon on the upper right of the screen. Select New Group label. 2) Input a new group name in pop up dialog box. 3) Click Confirm label to save. The group will be displayed on the left list. 5.2.5.2 Rename A Group 1) Click the group want to rename > click icon to enter edit page. 2) Input the new name directly. 3) Click Confirm label to save. 5.2.5.
NoteġAfter finish BLF Key configuration, drag ExtKey from the WIDGETS to the main interface. As shown below.
5.4 Intercom Select Type as Intercom, enter intercom code in Value. Choose the availed account. To click Confirm to save. Note: Different SIP server has different codes.
1. Press the Intercom key when the phone is available. The phone will connect the extension number of remote user automatically. 2. The phone enable silent mode when picking up the intercom call so that the other will not hear you. 5.5 Call Return This function can be used to call the latest dialed call record automatically.
5.6 BLFList BLF List˖While using BroadSoft platform, the accounts which are monitored by the sip phone will reply the subscribe news in the form of xml list to improve efficiency. BLF List Code˖While using BroadSoft platform, configure the BLF LIST CODEˈcan Pick up call or Barge in call. Note: BLFListCode is supported by Broadsoft platform, Please consult your administrator further information. 5.7 Pickup & Group Pickup User can use pickup to answer other users’ incoming call.
z Group pickup Group pickup can answer group’s user incoming calls. When anyone in group receives an incoming call, user can press the group pickup key to answer. Note: Press the group pickup only to answer line 1 incoming call if there are many lines incoming calls in group. 5.8 ACD Automatic Call Distribution (ACD) enables organizations to manage a large number of phone calls on an individual basis.
5.9 Hot Desking In some working place, the people are always walking around. HotDesking feature will make the staffs login his account on any computer in the company. In some public places, the working people is not fixed, anyone can use HotDesking for logging his account, and setting the phones to the familiar mode, such as the remote function of the computer.
5.10 Conference User can use the conference feature to hold a 3 way conference by pressing the Conference soft key to invite the current talking and one line talking held to attend conference. 5.10.1 Create 3 way conference 1. Create talking with first party; 2. Press to create a new talking; 3. Input the number of second party and press the Video Call or Auido Call to make a call; 4.
71
5.11 Transfer 5.11.1 Blind Transfer When the IP phone blind transfers a call. 1. During the first way conversation, press transfer key on the keypad or click enter the configuration interface. 2. Enter the transfer number, then click Blind label to transfer the number. Configuration interface shown as below.
5.11.2 Attended Transfer 1. During the first way conversation, press transfer key on the keypad or click enter the configuration intserface. 2. Enter the transfer number, then click Attended label to transfer the number. Configuration interface shown as below.
3. When the third party answered, press to comfirm the transfer. Shown as below. 5.12 Keypad Input Only numbers, * and # can be input by keypad. The default Input method is Android keyboard. User can also download the preferred input method from the internet. 5.13 Webpage Browser This section describes the default web browser in the video phone, and user can also download the preferred browser through the internet.
5.13.1 Open The Webpage 5.13.1.1 Browser Address Bar Run the browser, enter the URL in the address bar or direct input the information to search. After the input, user can click “Go” on the soft keyboard to complete. 5.13.1.2 Bookmark And Browsing History Run the browser, click to view the bookmark & history & saved pages. Icon description shown as below.
5.14 Camera 1. In the main screen, click > . 2. Slide right on the screen, view the photos and videos in “Gallery”. 5.14.1 Photograph Mode Turn on the camera, and the default mode is photograph mode. 5.14.1.1 Basic Setting pop up the menu on the right list. Click on the right upper corner nonsupport Click to enable/disable the reference grid Click to set the delay shutter to take photos 5.14.1.2 Mode Switch Slide right on the screen to switch the mode.
User can enter to set the resolution & quality to set the camera & video parameter. 5.14.1.3 Take A Photograph User can click the button to adjust the focal on the right side to take pictures. If user want length, use two fingers screen, shrinkage or expansion to adjust the focal length.
5.14.1.4 Take A Video Slide right on the screen to switch the mode. Click icon to switch to video mode. Click on the right side, video starts when the icon turns to . And click to stop the video recording and save. Shown as below. 5.15 Gallery User can use Gallery to view photos or videos, and user can also view the picture or video downloaded from the Internet. user can edit the photo or picture and set it as wallpaper.
Click the icon on the upper left corner, can view photos and videos in groups in the drop down list. Click on the folder to view all the photos. While viewing photos, user can use two fingers to press on the screen, shrinkage or expansion to shrink or enlarge the image. 5.
5.16.1 Turning Bluetooth On /Off z Press on screen z Click on Wireless & Networks. z Click or untick the option for Bluetooth. > click icon . 5.16.2 Changing Bluetooth Device Name The VP R48G uses “VP R48G” as Bluetooth device name by default. The device name will be visible to other devices when connecting them. Follow the steps below to change the name: z Press on screen z Click on Wireless & Networks. z Click on Bluetooth.
z If the VP R48G stops scanning before the other device is ready, turn off the R48G Bluethooth, then turn on again. z The discovered device will show in the available devices list with device ID. Make sure the Bluetooth device is active in pairing mode. Then tap on the device ID on the VP R48G to pair them. Confirm the passkey in the prompted message (if any). Or if PIN is required, please refer to the device’s documentation or other procedures to obtain the PIN. 5.16.
5.18 Calendar To start the calendarġ z In the main screenēclick icon > Calendar .
If one day has activity, color will appear on the calendar to remind. 5.18.1 Add An Account While using the calendar at the first time, it will remind you to add an account. Click ”Add account” to add an account, and then synchronize all the schedules of the account to the calendar. 5.18.2 View Calendar The calendar will display weekly by default, and you can slide the calendar up and down to view the different weeks.
create a the new activity: z Click on the date, and then click on the time period; z Click on ; 1) Input the details of the activity, 2) Click “Done” to finish. 5.18.4 Edit Activities You can click on schedule needed to be modified to edit the schedule. 5.18.5 Delete Activities While viewing the activity, you can click “DELETE” on the upper right corner to delete the activity. 5.19Clock Enter the Clock: z In the main screen, click > Clock icon As shown below. 84 .
Description: Alarm Default real time Countdown timer Stopwatch Time zone Others Others setting 5.19.1 Alarm User can add one or multiple alarms: 1) Click .
2) Click icon . 3) To set the hour and minute, click the digit on the right side to set hour and minute. 4) Then user can select enable or disable repeat the alarm in some days of a week, select the ringtone of the alarm and edit display label. If not modify, will present tomorrow as default.
5.19.1.1 Enable/Disable Alarm User can click icon to enable or disable the alarm. Note: If power off the phone, the alarm will also be off. 5.19.1.2 Modify Alarm If user want to modify the status of the alarm, including time, repeat data, alarm ringtone, can directly click on the alarm. 5.19.1.3 Delete Alarm In Alarm page, user click the alarm,after pop up the dialog box, select to delete the alarm. 5.19.2 Countdown Timer 1) Click .
3) Click icon to start the countdown timer. Click to stop the time. The other buttons are described as followed. Click to add one minute to countdown timer Click to delete the current countdown timer Click to add another countdown timer Click to reset the countdown timer 5.19.3 Stopwatch 1) Click icon . 2) Click icon to start the time. Click 3) In normal, click icon to stop the time. to remember the corresponding time. to reset the timer.
5.20 Gmail Email Application can let you use POP3 or IMAP service to send and receive e mail. Start Emailġ z In the main screen, click >Email 5.20.1 Add A New Gmail Account Make sure the email account has enabled POP3 or IMAP service, and you can add many accounts.
z If you have already set up an email account, In the main Email page, Press “Menu” button, and then click “Account”, and last press ”Menu” to “Add Account”. 1. Input the email account and password, and then click “Next”; 2. If there is no account type in the equipment database you want to set, the device will require you to enter more detailed information (the receiving server settings and outgoing server settings). 3.
User can click the labels of Artists, Albums or Songs to view all songs, view or play the songs from the playlists. To view the currently playing song, click the Now playing label to view . 5.22 Explorer User can use explorer to manage the files in the device. In the main screen, click icon > Explorer icon 91 . As shown below.
Click mnt to enter to show as below. If insert the USB device, will dislpayed in this layer. Shown as below. Click to modify the sort: by name, time,size,type Click to creat a new folder or photo folder 5.23 Video Player User can use video player to play local videos. To run the video player: In the main screen, click > Video icon . After entering, user can click on the list of videos to watch.
Screen Brightness Adjustment Click to adjust the volume Click to add into the Bookmark. The previous video, and long press to make video fast backward. Hold/Play. The next video, and long press to make video fast forward. Screen size adjustment, four type of video sizes: original size, full screen, 16:9, 4:3 Screen size adjustment, four type of video sizes: original size, full screen, 16:9.
5.23 Others 5.23.1 Apk Install User need open phone permission before installing. Go to the path: Settings >Security, enable Unknown sources. In the main screen, click >Explorer. Select the Apk you want to install, follow he prompt to operate.
6 Software Upgrade 6.1 Immediate Update Choose one way below to enter the system upgrade interface: z In the main screen, press “Menu” on board > System Settings > System > About Multimedia Terminal > System Upgrade > System Update Now z In the main screen, tap on settings icon > System > About device >System Update > System Update Now. Update interface as shown.
6.1.1 Select Other Upgrade Package 1) Via USB to Upgrade Put upgrade package into USB, insert USB, then click “Select other upgrade package”, find “/mut/usb_storage”, find the upgrade package, then click “OK” to upgrade. 2) Via Internal Memory to Upgrade Use USB to copy the upgrade package into Internal Memory, then press “Select other upgrade package”, find “/mnt/sdcard”ēfind upgrade document, then click “OK” to upgrade. 6.1.
and then use USB to copy the upgrade package into Internal Memory, enter the upgrade interface, you will find the path of upgrade package:/mut/sdcard/upgrade.zip, because video phone has searched it automatically, press “Local Update” to start upgrading. 6.1.3 Remote Update 1) Enter the interface in figure 5 1, click “Server Address”, and input the server address that contains upgrade package.
6.2 Auto Update Period Auto Update Period includes four modes: None, One Day, One Week, and One Month. The terminal will detect the new version automatically in time, if there is, the status bar will show “There is a new version, please update!”. Click and download the image for upgrade.
6.3 Upgrade on the web 1) Click Upgrade >Basic. 2) Click the 3) Click label to select the version to upgrade. to save. 6.4 Check Update After System Power On Click “Check Update After System Power On” . Shown as below.
Every time user power on, the system will check the new version automatically. If there is a new one, the status bar will notice: “System has new version, please update now!”, click and download the image for upgrade.
7 System Maintenance 7.1 System State Inspection Mode 1: In the main screen, click > Status info >Version info Mode 2: In the main screen, click > > About device It will display phone status, software version and hardware version in this item. 7.
Mode 3 and Mode 4 can check the corresponding network information in setting interface. 7.3 SIP Account Registration Query You can choose one of the following methods to enter the SIP account registration query. If the account is successfully registered, the icon will be light up in notification area of phone.
Mode 1: Press Speaker button or pick up to enter the dialing interface, click on upper right corner, check Account Manager. Mode 2: Slide down the top left , click the account, enter the setup interface, check Account Manager. 7.
z Please check whether the adapter fits this product requirement; z Please check whether the outlet is working properly. Failure 2: No voice when pick up the handset z Please check whether the connection of handset is working properly; z Please adjust the volume + key on keyboard when off hook the phone, Observe the display of “volume” prompt.
8 Web Interface 8.1 Web login 1. Open the browser on the computer. 2. Input the IP address in the address bar. 3. Enter the user name and password (user name: admin, password: admin), then click . 8.2 Status >Basic Click Status >Basic to check the phone information.
Sections Product Information Network Information Description To display the device’s information such as Model name, MAC address (IP device’s physical address),Hardware Model, Firmware version and Hardware firmware. To display the device’s Networking status(LAN Port),such as Port Type(which could be DHCP/Static), Link Status, IP Address, Subnet Mask, Gateway, Primary DNS server, Secondary DNS server.
Account Information To display device’s Account information and Registration status (account username, registered server’s address, Register result). 8.3Account >Basic Sections SIP Account Description To display and configure the specific Account settings. z Status: To display register result. z Display Label: Which is displayed on the phone’s LCD screen. z Display Name: Which is sent to the other call party for displaying.
SIP Server 1 To display and configure Primary SIP server settings. z Server IP: SIP server address, it could be an URL or IP address. z Registration Period: The registration will expire after Registration period, the IP phone will re register automatically within registration period. To display and configure Secondary SIP server settings.
NAT To display and configure NAT(Net Address Translator) settings. z STUN: Short for Simple Traversal of UDP over NATS, a solution to solve NAT issues. Note: By default, NAT is disabled. 8.
Sections SIP Account Audio Codecs Video Codecs Description To display current Account settings or to select which account to display. To display and configure available/unavailable Audio codecs list. Codec means coder decoder which is used to transfer analog signal to digital signal or voice versa. Familiar codecs are PCMU(G711U), PCMA(G711A), G722 (wid bandth codecs),G729 and so on. To display and configure available/unavailable Video codecs list.
Sections Subscribe Description To display or configure session timer settings. z Active: To enable or disable this feature, If enable, the ongoing call will be disconnected automatically once the session expired unless it’s been refreshed by UAC or UAS. z Session Expire: Configure session expire time. z Session Refresher: To configure who should be response for refreshing a session. Note: UAC means User Agent Client, here stands for IP phone.
Sections Call Description To display and configure call related features. z Max Local SIP Port: To configure maximum local sip port for designated account. z Min Local SIP Port: To configure minimum local sip port for designated account. z Caller ID Header: To configure which Caller ID format to fetch for displaying on Phone UI. z Auto Answer: If enabled, IP phone will be auto answered when there is an incoming call for designated account.
Sections Session Timer BLF List Broadsoft Description To display or configure session timer settings. z Active: To enable or disable this feature, If enable, the ongoing call will be disconnected automatically once the session expired unless it’s been refreshed by UAC or UAS. z Session Expire: Configure session expire time. z Session Refresher: To configure who should be response for refreshing a session.
Sections Net Conference User Agent Remote User Agent Description To display NAT related settings. z UDP Keep Alive message: If enabled, IP phone will send UDP keep alive message periodically to router to keep NAT port alive. z UDP Alive Msg Interval: Keepalive message interval. z Rport: Remote Port, if enabled, it will add Remote Port into outgoing SIP message for designated account. To select Local or network conference.
Sections Local RTP VLAN Description To display and configure Local RTP settings. z Max RTP Port: Determine the maximum port that RTP stream can use. z Min RTP Port: Determine the minimum port that RTP stream can use. To display and configure VLAN settings. z LAN Port/PC Port: You can configure VLAN setting for both ports respectively. z Active: To enable or disable VLAN feature for designated port. z VID: To configure VLAN id for designated port.
Sections Key Press Sound Ringtone Volume Description To configure the sound volume for key press. z Volume: The valid volume range is from 0~15,by default it’s 8. To configure the sound volume for ringtone. z Volume: The valid volume range is from 0~15,by default it’s 8. 8.8 Phone >Call Feature Sections Mode Phone Forward Transfer Description To enable or disable feature key sync. z Feature Key Sync: To enable or disable feature key sync.
Busy Forward and No answer Forward. z Always Forward: Any incoming call will be forwarded in any situation. z Busy Forward: Any incoming call will be forwarded if IP phone is busy. z No answer Forward: Any incoming call will be forwarded if it’s no answer after a specific time. Sections DND z z z z z z z Description DND(Do Not Disturb) allows IP phones to ignore any incoming calls.
incoming call if DND on. DND On Code: The Code used to turn on DND on server’s side, if configured, IP phone will send a SIP message to server to turn on DND on server side if you press DND when DND is off. z DND Off Code: The Code used to turn off DND on server’s side, if configured, IP phone will send a SIP message to server to turn off DND on server side if you press DND when DND is on. To enable or disable Call Waiting.
Sections Auto Redial Intercom Hot line ACD Remote Control Description Auto redial allows IP phones to redial an unsuccessful call for designated times within designated interval. z Auto Redial: To enable or disable auto redial feature. z Auto Redial Interval: Determine the interval between two consecutive attempts. z Auto Redial Times: Determine how many times to redial. Intercom allow user to establish a call directly with the callee.
Sections Key As Send SIP Config UACSTA Description Key As Send allows you to disable send key or assign pound key as send key. Setup the SIP protocol package interval. T2 is maximum. The interval should be larger the T1, but less then T2. Using CSTA for SIP phone user agents. It can control some features of calling. UACSTA is used to send ECMA 323(CSTA XML) information during SIP calling. The default status is disabled.
Door Phone Others When there is an incoming call from doorphone, setup the delay auto answer time, R48G will auto answer the call after the timeout. Note: if you enable Auto Answer function, this feature will be not available. z Return Code When Refuse: Allows user to assign specific code as return code to SIP server when an incoming call is rejected. z Auto Answer Delay: To configure delay time before an incoming call is automatically answered. 8.
Mic Volume Automatical Control NetEQ silence efficiently with special packets that indicate silence is occurring. It can facilitate speech processing, and deactivate some processes during non speech section of an audio session. It can avoid unnecessary coding or transmission of silence packets in VoIP applications, saving on computation and network bandwidth.
8.10 Phone >Video Sections Media Feedback H264 Settings Description z NACK: Enabled it to filter mosaic. z Tmmbr: Send the maximum temporary rate request. Disabled by default. H264: A video stream compression standard. Different from H263, it provides an approximately identical level of video stream quality but a half bit rate. This type of compression is sometimes called MPEG 4 part 10. To setup corresponding H264 video parameters.
Others z z z z z z Rate Control: Choose one H264 video rate. Hardware Endec Acceleration: This function is used to solve the image issue. User can enable the Hardware Endec Acceleration when you need. Hardware Decodec Acceleration: Disabled by default. Color Enhancement: To increase the phone display color. Enabled by default. Image Quality: User can select Low, Middle or High mode. Camera Priority: R48G can connect extra camera.
Sections Current Page Key Description R48G can support 4 pages Ext Key. 20 Ext Keys for each page. Allows user to assign specific feature to the designated key on expansion module. For keys, the available feature list: DND, Menu, MSG, Status, Book, Fwd, PickUp, Group PickUp, Intercom, Speed Dial, History, Favorites, Redial, Account, ACD, BLF, BLFList,Call Return, Hot Desking, Record, XML Browser, DTMF. 8.
8.13 Phone >Replace Rule Sections Rules Rules Modify Area Code Description Allow user to select Replace rule or Dial now to display or edit. Allow user to modify selected rules information. Once you dial prefix value, it will call out Replace number. z Click Add to add new replace rules. z Select account for the replace rule z Input a suitable prefix value .Enter the replace number. z Click Submit to save. All replace rules will show in the list.
code rule, the IP phone will automatically prefix outgoing number with area code. Note: There is only one area code rule supported. 8.14 Phone >Dial Plan Sections Rules Dial Now Delay Description Allow user to select Replace rule or Dial now to display or edit. Allow user configure dial now delay time for dial now.
Rules Modify Area Code Allow user to modify selected rules information, for dial now rule, user can modify related accounts, Dial now Rule itself. z Click Add to add new dial now number. z Select the related account for dial now. z Enter the number in Dial Now Rule area. z Click submit to save. All dial now numbers will show in the list. Users can edit or delete the exited dial now number. Area codes are also known as NPAs(Numbering Plan Areas).
8.
Sections Action URL Description To display and configure Action URL settings. Setup Completed: When the IP phone completes startup. z Registered: When the IP phone successfully registers an account. z Unregistered: When the IP phone logs off the registered account. z Register Failed: When the IP phone fails to register an account. z Off Hook: When the IP phone is off hook. z On Hook: When the IP phone is on hook. z Incoming Call: When the IP phone receives an incoming call.
z z z z z z incoming call. Reject Incoming Call: When the IP phone rejects an incoming call. Answer New Call: When the IP phone answers a new call. Transfer Finished: When the IP phone completes to transfer a call. Transfer Failed: When the IP phone fails to transfer a call. Idle To Busy: When the state of the IP phone changes from idle to busy. Busy To Idle: When the state of phone changes from busy to idle. 8.
Sections Multicast Setting Description To display and configure the Multicast setting. z Paging Barge: Setup the priority quantity. z Paging priority Active: Enable o disable the multicast. To setup the multicast parameters. z Listening Address: Enter the IP address you need to listen z Label ˖ Input the label for each listening address Priority List 8.
Sections Contact Search Dial Group Group Setting Import/Export Description To display and select local contact type. z All Contacts: To display or edit all local contacts. z Favorites: To display or edit favorites contacts. z Black List: To display black list contacts. To search designated contacts from local phonebook. To dial out a call or hangup an ongoing call from Web UI. Note: For this feature, you need to have the remote control privilege to control IP phone via Web UI.
8.18 PhoneBook >Remote Book Sections Remote Book Description To display and configure Remote Book settings. z Index: To select desired Remote Book item to display and configure.
8.19 PhoneBook >Call Log Sections Call History Description To display call history records. Available call history types are All calls, Dialed calls, Received calls, Missed calls, Forwarded calls. z HangUp: To click to hangup ongoing call on the IP phone. Note: For “HangUp” feature, you need to have the remote control privilege to control IP phone via Web UI. Please refer to section “Remote Control” in the Web UI >Phone >Call Feature page.
8.20 PhoneBook >LDAP Sections LDAP Description To display and configure LDAP phonebook settings. z Name Filter: The settings used to tell LDAP server what name attributes to search. z Number Filter: The settings used to tell LDAP server what number attributes to search. z Server: To configure LDAP server’s address. z Port: To configure LDAP server’s port. z Base DN: To configure searching base DN on LDAP server.
response from LDAP server. Search Delay Time: To configure delay time before initiate LDAP searching request after you input a value from Phone UI. Note: For setting details,please consult with your system administrator for further information. z 8.21 PhoneBook >Broadsoft Sections Broadsoft PhoneBook Description To display and configure Broadsoft PhoneBook settings. z PhoneBook Item: To select specific item to configure.
8.22 Upgrade >Basic Sections Firmware version Description To display firmware version, firmware version starts with MODEL name. Hardware Version To display Hardware version. Upgrade To select upgrading zip file from local or a remote server automatically. Note: Please make sure it’s right file format for right model. Reset to Factory Setting To setup R48G to factory setting. Reset Config to Factory To setup the configuration file to factory setting.
Sections PNP Option Description To display and configure PNP setting for Auto Provisioning. z PNP: Plug and Play, once PNP is enabled, the phone will send SIP subscription message to PNP server automatically to get Auto Provisioning server’s address.By default, this SIP message is sent to multicast address 224.0.1.75(PNP server address by standard). Sections Manual AutoP Description To display and configure manual update server’s settings.
access, otherwise left blank. Common AES Key: Used for IP phone to decipher common Auto Provisioning configuration file. z AES Key (MAC): Used for IP phone to decipher MAC oriented auto provisioning configuration file(for example, file name could be 0c1105888888.cfg if IP phone’s MAC address is 0c1105888888). Note: AES is one of many encryption, it should be configure only configure filed is ciphered with AES, otherwise left blank.
PCAP Others PC. To start, stop packets capturing or to export captured Packet file. z Start: To start capturing all the packets file sent or received from IP phone. z Stop: To stop capturing packets. Note: IP phone will save captured packets file to a temporary file, this file maximum size is 1M(mega bytes), and will top capturing once reaching this maximum size. To display or configure others features from this page.
8.25 Security >Advanced Sections Web Server Certificate Web Server Certificate Upload Description To display or delete Certificate which is used when IP phone is connected from any incoming HTTPs request. Note: The default certificate could not be deleted. To upload a certificate file which will be used as server certificate.
Sections Client Certificate Client Certificate Upload Description To display or delete Certificates which is used when IP phone is connecting to any HTTPs server. To upload certificate files, this is used as client certificate. z Only Accept trusted Certificates: If this option is enabled, only trusted certificates will be accepted.
