Contents Introduction............................................................ 3 Technical Support .............................................................................................................. 4 Precautions ....................................................................................................................... 4 Specifications..................................................................................................................... 6 Package Content..............
5. Use USB Host ..................................................... 47 6. Connect to External AV Device .................................... 49 6.1 Connect Video Cable ...................................................................................................49 6.2 Connect Audio Cable ...................................................................................................50 7. Basic Setup ....................................................... 53 7.1 Video Setup .......................
Introduction MediaGate MG-350HD fully supports HD (High Definition) files that are really clear through HDTV (LCDTV, Normal TV) and can stream the contents from a PC through wireless (802.11g) or wired LAN, and also has USB host that you can plug an external USB storage.
Technical Support Contact your local distributor in your country or AL Tech, Inc. in Korea www.airlinktek.com Tel 82-2-3011-9219 Fax 82-2-566-6186 E-mail sales@airlinktek.com Precautions Please read the followings carefully and refer to [Cautions] in the manual for proper use. Copyright Check the supported codec * We are not responsible for using illegal software, audio sources, video sources, etc and the users should take the legal responsibility. * MediaGate may not play all media files.
of this port and the defect due to other misusing. Data Backup * We strongly recommend you to back up the data to another safe media. We are not responsible for data damage or loss in builtin HDD. * Make sure to use the supplied car charger (optional) in a car. Cautions for use in a car Don’t use MediaGate during driving. MediaGate may not work properly when the engine is stopped and it may cause battery discharge. Using in a car may have video & audio noise.
Specifications Product Name MediaGate MG-350 HD Power 5V 1.5A /12V 1.5A Weight 564g (without HDD & wireless antenna) Dimension 57 x 150 x 185 mm (without wireless antenna) Available OS USB Device USB Host USB Device Compatible: Windows 98SE/ME/2000/XP, Mac OS 9.0 higher, Linux 2.4 higher NDAS Compatible: Windows 2000, XP Device Port x 1ea, 480Mbps USB 2.0 (USB 1.1 compatible) Host Port x 1ea, 480Mbps USB 2.0 (USB 1.
Package Content ① MG-350 HD - 1ea ② Wireless Antenna -1ea ③ Stand(Cradle) – 1ea ④ Remote controller, battery – each 1ea ⑤ AV cable (composite + stereo cable) – 1ea ⑥ USB cable (for connecting to PC) -1ea ⑦ Power adapter – 1ea ⑧ Setup CD (NDAS PC software, Windows 98 Driver) -1ea ⑨ User manual – 1ea 7
Product Overview < Front View > ① ENTER ② △▽◁ ▷ ⑤ STOP/INIT ③ POWER ⑥ IR ④ PLAY/PAUSE ⑦ PWR ⑧ NET ⑨ HDD Front View ① ENTER Select or play a file ② △▽◁ ▷ Navigation Key, Up, Down, Left, Right ③ POWER Power On, Off ④ PLAY / PAUSE Play all files from selected file / Pause ⑤ STOP / INIT Stop / Return to Mode Selection Screen ⑥ IR IR receiving area for remote signals ⑦ PWR Power LED ⑧ NET Network LED ⑨ HDD HDD LED 8
< Back View > ① MULTI I/O ② USB DEVICCE ⑩ ANT ③ USB HOST ⑪ OPTICAL ④ DVI ⑫ CVBS ⑤ S-VIDEO ⑬ STEREO L-R ⑥ COAXIAL ⑦ Y, PB, PR ⑧ LAN ⑨ PWR Back View ① MULTI I/O 24 pin standard connector (no use, this is only for additional specified device) ② USB DEVICE Connect to a computer with USB cable ③ USB HOST Connect to an external USB device with USB cable ④ DVI Connect DVI cable for video output ⑤ S-VIDEO Connect S-Video cable for video output ⑥ COAXIAL Connect Coaxial cable for 5.1 ch.
Use as External USB HDD 10
1. Use as External USB HDD 1.1 Insert Hard Disk 9 Use 3.5” IDE Hard Disk for Desktop. 9 Hard Disk should be “Master”. However, if the Hard Disk supports “Single” mode, you need to try to set “Single “mode. ① Unscrew 4 spot and open the side cover case with pulling to the arrow direction ② Connect Power and IDE connector to Hard Disk. ③ Close the side cover case with pulling to the arrow direction.
1.2 Format Built-in HDD via USB If the built-in HDD is not formatted, PC can not detect the hard disk drive. If so, format the hard disk first referring to the following guide. * If the hard disk drive is already formatted, see “1.3 Copy Data via USB”. 1.2.1 Windows 98SE, ME 1) Install Windows 98 Driver. Find the driver at Windows 5) Select “5. Chang current fixed disk drive” and press 98 CD>MediaGate MG-350HD>English>Windows 98 [Enter]. Driver Directory.
8) Select “ 1. Create Primary DOS Partition ” and press 11) Type the capacity or % which you want to use and press [Enter]. [Enter]. 12) Drive integrity verification will start again. After finishing that, press [ESC] key when the “Primary DOS Partition created, drive letters changed or added” message displays. 9) Wait until finishing verifying the drive integrity. 13) Press [ESC] key again. “ Shut down Windows before restarting” message will be displayed. Press [ESC] key finally for exiting FDISK.
14) Type “ exit ” command at “ C:\WINDOWS> ” and press [Enter] for returning to windows screen. 15) Unplug the MG-350HDand plug again. New volume will be appeared at [My Computer]. Click mouse right button at the new volume and select [Format]. 1.2.2 Windows 2000 1) Connect MG-350HD to PC via USB cable, and plug 3) If the [Disk Signature and Upgrade Disk Wizard] is started, power cable of MG-350HD. click Next to progress for finishing the wizard.
5) Click [Next] at the Create Partition Wizard Windows. 9) Choose FAT32 or NTFS at File system to use and click [Next]. 6) Check [Primary Partition] and click [Next]. 9 FAT 32 system is available on windows 98SE/ME/2000/XP, but NTFS system is available on windows 2000/XP only. 7) Type number that you want to use and click [Next]. 9 If you choose FAT32 system on Windows 2000/XP, one drive letter’s maximum size will be limited to 32GB.
1.2.3 Windows XP 1) Connect MG-350HD to PC via USB cable, and plug 6) Check [Primary Partition] and click [Next]. power cable of MG-350HD. 2) Click [Settings > Control Panel > Administrative Tools > Computer Management>Disk Management] on Windows. If you can not find Administrative Tools at Control Panel, click “ switch to classic view” in left – up corner on screen. 3) If the [Disk Signature and Upgrade Disk Wizard] starts, click [Next] to progress for finishing the wizard.
9) Choose FAT32 or NTFS at File system to use and click [Next]. 9 FAT 32 system is available on windows 98SE/ME/2000/XP, but NTFS system is available on windows 2000/XP only. 9 If you choose FAT32 system on Windows 2000/XP, one drive letter’s maximum size will be limited to 32GB. If you want to use one drive letter of 32GB more, you have to format on windows 98SE/ME.
1.3 Copy Data via USB It is possible to use as a external USB hard disk drive in case of inserting hard disk into MG-350HD. You can copy data from your PC to built-in HDD of MG-350HD via USB. It is possible to play media files at the hard disk on TV set. * When connecting PC, you have to connect power cable of MG-350HD. 1.3.1 Windows 98SE 9First, you have to install Windows 98 Driver before connecting PC. Find the driver at Windows 98 driver CD>MediaGate MG350HD>English>Windows 98 Driver Directory.
1.3.2 Windows ME 1) After connecting MG-350HD and plug power cable. 3) After copying data, remove MG-350HD with using Windows itself will install driver automatically. And then, remove icon check the driver installation at Windows [Start > Settings > don’t follow this procedure, data and MG-350HD may have Control Panel > (view all Control Panel options) > System > damage.
1.3.3 Windows 2000, XP 1) After connecting MG-350HD and plug power cable, 3) After copying data, remove MG-350HD with using Windows itself will install driver automatically. And then, remove icon check the driver installation at Windows [Start > Settings > don’t follow this procedure, data and MG-350HD may have Control panel > (switch to classic View on Windows XP) > damage. at Windows right-down corner.
1.3.4 Linux 9It can be available on Linux 2.4 higher. [Automatic Mount] After booting, do log-in. Connect MG-350HD -> Power On MG-350HD -> Check the detection with [fdisk] -> make Mount Pointer (ex. mediatest) at Folder Mount(/mnt) -> Edit [/etc/fstab] -> add the following; /dev/sda /mnt/mediatest vfat noauto, user 0 0 (in case of FAT32 HDD) /dev/sda /mnt/mediatest ntfs noauto, user 0 0 (in case of NTFS HDD) Do Log-in again.
Connect to PC via Network 22
2. Connect to PC via Network 2.1 Wired LAN Connection When connecting Computer to MG-35 directly When connecting with IP Router or Hub Connect LAN cable to LAN port between MG-350HD and PC. In this case, you have to use Cross LAN cable type generally. Connect LAN cable to LAN port between IP Router or Hub. [TIP] If the computer’s LAN card was connected to In this case, you have to use Direct LAN Cable type generally.
2.2 Wireless LAN Connection MG-350HD supports two types of wireless structure-Infrastructure mode & Ad-Hoc mode. Ad-Hoc Mode 1:1 wireless LAN connection type between wireless adapter and Mg- Infrastructure Mode 350HD without wireless access point. Wireless LAN connection type with Wireless Access Point. √ Note Wireless AP (Infrastructure Mode) or Wireless Adapter (Ad-Hoc Mode) is needed for wireless connection. IEEE 802.11g wireless standard is recommended for better wireless environment.
④ Select preferable one out of the scanned wireless stations. *Wireless station information is displayed. -SSID: Name of Wireless Station -Connection Mode: AP Mode (to connect an AP) : Ad-hoc Mode (to connect wireless adapter) -Channel: Wireless channel used by wireless station ⑤ Information of wireless station will be displayed. Press [SETUP] for saving configurations. √ Note: When connecting Ad-Hoc Mode, manual setting of IP Address and Subnet mask will be needed.
⑥ [WIRELESS] icon is activated. Run the icon, and the PC list on the network is displayed. Access to the preferable PC you want. √ Note: When wireless icon is not activated or not connected to wireless station. 1. [Waiting or Rebooting] It might take some time to assign IP address from AP in case of AP Mode. So, wait for a while. Otherwise, reboot AP and MG-350HD together. 2.
√ Note: When connecting to AP with WEP wireless security If wireless station like AP or Adapter has WEP wireless security, you have to enter WEP key same as AP or wireless adapter. It is possible to enter WEP key at “ Wireless-II” . Enable Security Mode and then enter WEP Key of AP or wireless adapter. *How to enter=use direction key [UP] or [DOWN], or [Number]. After finishing that, finally press [SETUP] for saving configurations.
Shared File Playback (Stream) 28
3. Shared File Playback (Stream) After connecting LAN cable, you have to set network configurations of both Computer and MG-350HD. *It is possible to assign IP address and Subnet Mask of MG-350HD as dynamic or static. 3.1 Windows 98SE, ME 1) Select a folder which you want to share. Right-click the 3) After that, the shared folder will be displayed as following folder and click ‘sharing’ in pop-up menu. picture.
After writing, press [SETUP] again for saving configurations. 9If you have already been provided dynamic IP address from DHCP Server or IP Router on your local area network, you don’t need to write static IP address absolutely. Use ‘DHCP on’ or write IP address & Subnet mask that DHCP Server or IP Router provide.
3.2 Windows 2000 1) Select a folder which you want to share. Right-click the 9Recommend only to use ‘Read>Allow’ at Permissions. folder and click ‘Sharing’ in pop menu. 2) Check ‘Share this folder’ and write ‘share name’. For example, “My Movie” 9Make sure to write ‘share name’ within 12 characters in 4) After that, the shared folder will be displayed as following English. picture.
6) Check ‘User cannot change password’ and ‘Password never expires’. 9) Check ‘Use the following IP address’, and write ‘IP address’ & ‘Subnet mask’ that you want to use. For example, 7) Move to [Control Panel>Network and Dial-up IP address: 192.168.1.3 Connections], and select Properties of ‘Local Area Subnet mask: 255.255.255.0 Connections’ by right click of mouse. 9If you see two or more ‘Local area connections’, select one that you will use for connecting to MG-350HD.
6) Set the network configurations of MG-350HD. ` 9You have to connect MG-350HD to TV set for this setup. See “6.1 Connect Video Cable”. Press [SETUP] of remote control for moving to setup screen. On that screen, select ‘DHCP Support Off’ and write IP address & Subnet mask. For example, IP Address: 192.168.1.2 Subnet mask: 255.255.255.0 After writing, press [SETUP] again for saving configurations.
3.3 Windows XP 1) Select a folder which you want to share. Right-click the 3) After that, the shared folder will be displayed as following folder and click ‘Sharing and Security’ in pop menu. picture. 4) Move to [Settings>Control Panel>Administrative Tools>Computer management>Local Users and Groups>Users], and double click ‘Guest’. 9This is for Windows XP Professional. Windows XP Home users can’t see this figure. Go to next number 6).
. 7) Double click ‘Internet Protocol(TCP/IP)’ that you want to use on your computer. 6) Move to [Control Panel>Network connections], and select ‘Local area connections’ properties by right click of mouse. 8) Check ‘Use the following IP address’, and write ‘IP address’ & ‘Subnet mask’ that you want to use. 9If you can’t find ‘Administrative Tools’ at Control Panel, click “Switch to classic view” in left-up corner on screen.
Check ‘Off’ and click ‘OK’ 9If you have already been provided dynamic IP address from DHCP Server or IP Router on your local area network, you don’t need to write static IP address absolutely. Use ‘Obtain an IP address automatically on’ or write IP address & Subnet mask that DHCP Server or IP Router provide. 9) At above number 7) figure, click ‘Advanced’ Tab. Disable ‘Internet Connection Firewall’. 6) Set the network configurations of MG-350HD. 9You have to connect MG-350HD to TV set for this setup.
After writing, press [SETUP] again for saving configurations. 9If you have already been provided dynamic IP address from DHCP Server or IP Router on your local area network, you don’t need to write static IP address absolutely. Use ‘DHCP on’ or write IP address & Subnet mask that DHCP Server or IP Router provide. 9Check ‘IP address obtained automatically’ When you use ‘DHCP On’, you can see the IP address on information screen with pressing [INFO] button.
3.4 Windows Vista Before you do “folder sharing”, you need to set up 3 things for Network sharing. 1. Setup of User Accounts and Family safety a. Click Start > Settings > Control Panel > Users Accounts and Family safety b. Make sure the account is “Guest”. c. If the “Guest” account is off, then switch it to “On”.
2. Disable “Firewall” a. Click Start > Setting > Control Panel > Security > Windows Firewall on / off b.
3. Setup of Network and Sharing Center a. Click Start > Setting > Control Panel > Network and Internet > Network and Sharing Center b. Select “Password Protected sharing” and select “Turn off password protected sharing”. c. make a folder you want to share.
d. You will get a popup “Choose people to share with” then select “Everyone (All users in this list) and press “Add” button. e. After you register the user account, then click “Share” button.
Use as Network Storage (NDAS) 42
4. Use as Network Storage (NDAS) √ Note -Recommend to use 100Mbps LAN Card on PC on using wired LAN connection. -Recommend to use IEEE 802.11g (54Mbps) wireless adapter or Access Point when using wireless LAN connection. -NDAS function allows to transfer data to HDD in MG-350HD by wired or wireless LAN without setting data sharing works. -Recommend Pentium III higher and 128MB RAM higher PC (System requirement) -NDAS PC software works on Windows 2000/XP only.
③ NDAS icon is created at right-down corner on desktop windows. Right click the icon and select Register New Device” ④ Write NDAS Device ID and Write Key. They are located on the bottom of MG-350HD. Write your preferable name at NDAS Device Name. Finish device registration procedure with clicking [Register]. ⑤ Select Mount(Read/Write) and access to NDAS Device, i.e, MG350HD. ⑥ Select “Install the software automatically” and click [Next] button.
⑦ Please check ‘My Computer’ if Hard Disk in MG-350HD is conceived as Hard Disk Drive of local network. (HDD in MG-350HD looks like external Hard Disk Drive. C:, D:, E: or F: )If you cannot see Hard Disk Drive, please turn off MG-350HD and turn on again. (Recognition can take some time.) ⑧ To remove NDAS function safely, please double click the icon in right bottom tray. (just like removing external Hard Disk Drive.
. Use USB Host 46
5. Use USB Host √ Note: How to eject the tray of external USB ODD (Optical Disk Drive) Stop playback and press number [3] button in order to eject the tray of external USB ODD. In addition, original DVD title with CSS Lock should not be played when connecting with USB host, but it is possible to play other format like XviD. √ Note It shall not be compatible with any external USB device. There are so many external USB devices, and specific products should not be compatible.
Connect to External AV Device 48
6. Connect to External AV Device 6.1 Connect Video Cable MG-350HD supports 4 type of video output; “Composite, S-video, Component, DVI”. Use video connection that your TV supports. Normally, TV supports composite video connection, and this package supplies composite video cable. ① Composite: Yellow RCA cable.
6.2 Connect Audio Cable MG-350HD supports 3 type of audio output; “Stereo, Coaxial, Optical”. Use audio connection that your TV or Audio set supports. Normally, TV supports stereo audio connection, and this package supplies stereo audio cable. ① Stereo: Red & White RCA Cable (supplied) Red (STEREO-R) Red (STEREO-R) (STEREO-L) White (STEREO-L) White Connect Stereo-R Jack of TV. Connect Stereo-L Jack of TV. ② Optical ( ): Optical Cable for Digital 5.1 ch.
51
Basic Setup 52
7. Basic Setup 7.1 Video Setup This is guide for setting video output of MG-350HD. You have to setup MG-350HD’s video output mode same as TV set’s video input mode. √ When you can not see normal screen after connecting video cable, check followings, 1. “TV “– Switch to Video Input Mode: Turn on TV, and switch to video input mode same as video connection. See TV user manual. 2. “MG-350HD” – Switch to Video Output Mode: Press [TV OUT] button repeatedly.
1080i 1080p 9NTSC, PAL : Standard of TV Output. Select a proper one for using in your country. < Setup Procedure > ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Video Out’ icon and press [OK]. Setup box will be screen. displayed under icon menu. ③ Select a TV Out Mode and each detailed video output mode according to the selected TV Out, and then press [OK]. ④ Finally, press [SETUP] again for saving configurations.
7.2 Audio Setup This is guide for setting audio output of MG-350HD. You can use Stereo or Digital 5.1 ch. 9Analogue/DCPM: Select when you connect the supplied audio cables (Red / White) to TV or Audio set directly. 9Encoded Digital: Select when you want to listen through 5.1Ch / DTS Dolby by connecting receiver (or amplifier) with Optical or Coaxial cable. < Setup Procedure > ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Audio Out’ icon and press [OK]. Setup box will be screen.
< ‘DHCP Support On’ Setup Procedure > ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Network’ icon and press [OK]. Setup box will be screen. displayed under icon menu. ③ Select ‘DHCP Support-ON’ and press [OK]. ④ Finally, press [SETUP] again for saving configurations. √ Check the obtained IP address Press [INFO] on Mode Selection screen, and It is possible to current obtained IP address from DHCP server.
① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Network’ icon and press [OK]. Setup box will be screen. displayed under icon menu. ③ Select ‘DHCP Support-OFF’ and press [OK]. ④ Move to ‘IP Address’, ‘Subnet’ and press [OK]. Input box will be displayed and enter number with [Direction] button or [Number] button. Finally, press [ENTER] for saving configurations.
7.4 Wireless Setup Refer to "2. Connect to PC via Network > 2.2 Wireless LAN Connection”. 7.5 Wireless Security Setup Refer to "2. Connect to PC via Network > 2.2 Wireless LAN Connection”. 7.6 LED Setup It is possible to turn on or off a backlight LED of arrow button on the front side. When the LED disturbs you in night, turn off the LED. ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Network’ icon and press [OK]. Setup box will be screen. displayed under icon menu.
7.7 Photo View Setup When playing photo file, it is possible to enable or disable BGM and set the playback interval time of each photo files. √ BGM, Music Slide Show Make a 'music' folder (in a small letter not a capital letter at root directory) of built-in HDD and save MP3 files at the folder. If the HDD is divided into two or more partitions, make a 'music' folder at first partition. When you play one or all photo files, you can listen mp3 and see photo slide show together.
7.9 Screen Ratio Setup This is guide for setting TV Type. You can use 4:3 Letter Box, 4:3 Pan Scan, and 16:9. < Setup Procedure > ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Scr. Rate’ icon and press [OK]. Setup box will be screen. displayed under icon menu. ③ Select one out of ‘4:3 Letter Box’, ‘4:3 PanScan’ or ’16:9’, and press {OK}. ④ Finally, press [SETUP] again for saving configurations.
7.10 Auto Play Setup When this Auto Play function is On, MG-350HD play the file continuously form the time of being stopped. < Setup Procedure > ① Turn on MG-350HD and press [SETUP] on Mode Selection ② Move to ‘Auto Play’ icon and press [OK]. Setup box will be screen. displayed under icon menu. ③ Select one out of ‘ON’ or ‘OFF’ and press {OK}. ④ Finally, press [SETUP] again for saving configurations.
7.11) Internet (How to setup the Internet) This is for how to connect MG-350HD to the Internet. ① After turn MG-350HD on, press [SETUP] button and go to ② Go to the 2nd page and select [INTERNET] icon and press [SETUP] page. [ENTER] button then you will get the above page. ③ By using arrow buttons, go to the bottom setup. By using arrow & number keys, set the configuration and press [ENTER] for saving of the configuration. ④ Press [SETUP] button for the saving of the configuration.
7.12) i-RADIO Refer fot the below how to set up the “i-Radio” on MG-350HD. √ [Note] It composes of Shoutcast , Inlive ( live broadcasting list scan ) and UserList. ( save pls, m3u files in “iradio “ folde.). < How to setup > ① After turn MG-350HD on, press [SETUP] button and go to ② Go to the 2nd page and select [i-RADIO] icon and press [SETUP] page. [ENTER] button then you will get the above page. ③ By using arrow buttons, go to the bottom setup.
< In case, select [Off] at the server list > √ [Note] After you made “iradio” folder at the root directory in the HDD of MG-350HD, it shows only the list saved in pls, m3u file. ① Press ◀ key at the main page, select “i-RADIO” icon and ② It shows server lists saved in the “iradio” folder at the root press [ENTER] button. directory. Select a list and press [ENTER] button then it plays. < In case, select [ Shoutcast / Inlive ] at the server list > ① It shows the live broadcasting server list.
7.13) SKIN With SKIN function, you can make your own GUI of MG-350HD. √ [Note] Save your own GUI or icon images in “skin1” folder at the root directory of MG-350HD. < How to setup > ① After turn MG-350HD on, press [SETUP] button and go to ② Go to the 2nd page and select [SKIN] icon and press [SETUP] page. [ENTER] button then you will get the above page. ③ By using arrow buttons, go to the bottom setup.
< How to setup > ① Make “skin1” folder and save “GUI” or “Images” in the folder ② At Setup page of SKIN, select [ON] of [SKIN Support] and at the root directory in a HDD of MG-350HD select [SKIN folder]. Press [SETUP] button for saving the configuration. ④ As the above, it supports several font colors. ③ Now, you see the changed GUI. If you can not see the font, then change the font color. (Setup Page => SKIN=> Change Font Color) √ For more detail information regarding SKIN, refer to www.airlinktek.
7.14) Others You can set up for 1) effect sound, 2) screensaver. < How to setup > ① After turn MG-350HD on, press [SETUP] button and go to ② Go to the 2nd page and select [ETC] icon and press [SETUP] page. [ENTER] button then you will get the above page. ③ By using arrow buttons, go to the bottom setup. By using arrow & number keys, set the configuration and press [ENTER] for saving of the configuration. ④ Press [SETUP] button for the saving of the configuration.
How to Play(Remote Control) 68
8. How to Play(Remote Control) 8.1 Basic Screen Menu 8.1.1 Mode Selection After turning on MG-350HD, you can see mode selection screen. In this screen, you can select HDD(built-in), USB(external USB device), LAN(wired network), WIRELESS(wireless network) You can select one out of them. √ Note HDD: Built-in HDD, USB: external USB device, LAN: wired network, WIRELESS: wireless network. Each Mode icon is activated when connecting to each external device. 8.1.1.
8.1.1.2 Wired & Wireless Network Following example is in case of wired network. Wireless network is same as wired network. ① [Mode Selection] Select ‘LAN’ icon and press [OK]. (In case ② [PC List on Network] PCs list is displayed on the network. Press [OK] and access to the network PC. of wireless network, select ‘WIRELESS’ icon, ③ Shard folder of PC is displayed. In order to play, select a file and press [OK]. √ Refresh Network PC Press [STOP]. If so, network PC list is refreshed.
8.1.2 File Selection Select a file and press [OK] in order to play. Function and Button Descriptions Remote Control Function Descriptions MENU Menu Icon ▲▼◀▶ Direction Key Direction key PREV I◀◀ Move by page In case of two or more file list page, move to previous page. NEXT ▶▶I Move by page In case of two or more file list page, move to next page. SLOW (↖) Up directory DEVICE Mode Selection Menu Icon is displayed including ‘Play one, Play all and Play-list’.
ALL MEDIA All Media Mode INFO - All media files are displayed including movie, music and photo. Current information of MG-350HD is displayed. When pressing this button, video output signal is changed repeatedly. TV OUT Video Out Signal (If you can not see normal screen, press this button repeatedly until returning normal screen. Brt.CONT Control luminosity, color depth, brightness SETUP - When pressing this button, 3 modes switch. After selecting a mode, change settings with ▲▼ arrow buttons.
8.2 Play Video Files Select a file and press [OK]. When pressing [MENU] while playing a file, “Tool Box Menu” is displayed. Tool Box allows using detailed playback function. Function and Button Descriptions 리모컨 버튼 기능 MENU Tool Box Playback OK ▶II NEXT ▶▶I PREV I◀◀ Pause 설명 Tool Box is displayed. For returning to playback, press again. Play file. When pressing while playing a file, pause the playback. For returning to playback, press again.
backward. SLOW SEARCH VOLUME + Direction ▲ VOLUME Direction ▼ MUTE Playback Slow Jump to Preferable Playback Time Volume Up Volume Down Sound Off Subtitle Move & Size Subtitle Sync. SUBTITLE Subtitle Select or Hide Play slowly 1/2x, 1/4x, and 1/8x whenever pressing this button. Move to a selected time of a file. Enter your preferable playback time with [Number] and press [OK]., or use time searching bar) Volume up. Volume down. Mute the sound. In order to hear sound, press this button again.
8.3 Play DVD File DVD manager function support to play DVD Ripping File same as original DVD. Make a folder and then save all ripping files into the folder. After connecting TV (or Monitor), select VIDEO_TS.IFO file at the folder. Make sure that all the ripping files including VIDEO_TS.IFO from one DVD title will be located at one folder. √ Nolte If you can not find VIDEO_TS.IFO file among all the ripping files from an original DVD title, DVD manager function will not work.
REPEAT Chapter, Title Repeat A-B REPEAT A-B repeat TITLE Go to Title Menu ANGLE Angle INFO SEARCH Brt. CONT Show File Information Jump to Preferable Playback Time Control luminosity, color depth, brightness NEXT Playback ▶▶I Next Chapter PREV Playback I◀◀ Previous Chapter FF ▶▶▶ Fast Forward REW ◀◀◀ Rewind Playback OK ▶II VOLUME + Direction ▲ VOLUME Direction ▼ MUTE Pause Volume Up Volume Down Sound Off Set chapter, title repeat. Set the A-B repeat.
8.4 Play Audio File Select a file and press [OK]. When pressing [MENU] while playing a file, “Tool Box Menu” is displayed. Tool Box allows using detailed playback function. Function and Button Descriptions Remote Control MENU Function Tool Box Playback OK ▶I NEXT ▶▶I PREV I◀◀ Pause Playback Descriptions Tool Box is displayed. For returning to playback, press again. Play file. When pressing while playing a file, pause the playback. For returning to playback, press again.
Playback Time VOLUME + Direction ▲ VOLUME Direction ▼ Volume Up Volume Down MUTE Sound Off INFO Show File Information Brt. CONT Control luminosity, color depth, brightness Enter your preferable playback time with [Number] and press [OK]. Volume Up. *It is not possible to use this button when manual subtitle is displayed while playing audio file. Volume Down. *It is not possible to use this button when manual subtitle is displayed while playing audio file. Mute the sound.
8.5 Play Photo File Select a file and press [OK]. When pressing [MENU] while playing a file, “Tool Box Menu” is displayed. Tool Box allows using detailed playback function. Function and Button Descriptions Remote Control MENU Function Tool Box Playback OK ▶I NEXT ▶▶I PREV I◀◀ INFO Brt. CONT Pause Playback Descriptions Tool Box is displayed. For returning to playback, press again. Play file. When pressing while playing a file, pause the playback. For returning to playback, press again.
√ Photo Slide Show When play mode is set on ‘Play all(Default value)’, all photo files will be played continuously. So, It is possible to use as photo slide show. √ Music Slide Show Make a 'music' folder (in a small letter not a capital letter at root directory) of built-in HDD and save MP3 files at the folder. If the HDD is divided into two or more partitions, make a 'music' folder at first partition. When you play one or all photo files, you can listen mp3 and see photo slide show together.
8.6 Make a Play List You can make your preferable play list for registering some files to play list. √ Note After rebooting MG-350HD, registered play list will be clear. ① Select your preferable file for registering with [SELECT] or ② After finishing registration, press [MENU] and select “Play [SELECT ALL]. List”. ③ Play List screen is displayed. -Play: Play the registered files. -Cancel: Close the Play List screen. -Move up, down: Change the file location.. -Shuffle: File location is mixed randomly.
Firmware Upgrade 82
9. Firmware Upgrade Download a upgrade file from local distributor in your country or visit at www.airlinktek.com. After connecting TV set, move to the upgrade file and press [OK]. Upgrade is progressed automatically. After finishing upgrade, you can check firmware version on Setup screen. Press [SETUP] button. * Current firmware version is displayed when pressing [INFO] button on file selecting screen.
