Warranty

ManualsBrandsAladdin ManualsOutdoorsSta-Rite P2RA DuraGlas/MaxiGlas Pump Kit

DURA-GLAS and MAX-E-GLAS

™

CENTRIFUGAL PUMPS with TRAP

O W N E R’ S M A N U A L

INSTALLATION, OPERATION & PARTS

Series PE, PEA, P2R, P2RA

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000

10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Customer Suppport: (800) 831-7133

Sta-Rite®, Max-E-Glas™ and Pentair Water Pool and Spa® is a trademark and/or a registered trademark of Pentair Water Pool and

Spa, Inc. and/or its affiliated companies in the United States and/or other countries. Plasto-Joint Stik® is a registered trademark of

La-Co Industries, Inc. Teflon® is a registered trademark of E.I. Du Pont De Nemours and Company Corporation. Unless noted, names

and brands of others that may be used in this document are not used to indicate an affiliation or endorsement between the proprietors

of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registered

trademarks of those partiesor others.

04-15-10

S413 (Rev. A)

This manual should be furnished to the end user of this pump; its use will

reduce service calls and chance of injury and will lengthen pump life.

1917 0895 NF

Summary of content (16 pages)

PAGE 1
DURA-GLAS and MAX-E-GLAS™ CENTRIFUGAL PUMPS with TRAP O W N E R’ S M A N U A L 1917 0895 NF INSTALLATION, OPERATION & PARTS Series PE, PEA, P2R, P2RA This manual should be furnished to the end user of this pump; its use will reduce service calls and chance of injury and will lengthen pump life. © 2010 Pentair Water Pool and Spa, Inc. All rights reserved. 1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000 10951 West Los Angeles Ave.
PAGE 2
‘PE’ and ‘P2R’ SERIES PUMPS WITH TRAP READ AND FOLLOW SAFETY INSTRUCTIONS! To avoid unneeded service calls, prevent possible injuries, and get the most out of your pump, READ THIS MANUAL CAREFULLY! This is the safety alert symbol. When you see this symbol on your system or in this manual, look for one of the following signal words and be alert to the potential for personal injury.
PAGE 3
INSTALLATION Before pressure testing, make the following safety checks: Only qualified, licensed personnel should install pump and wiring. • Check all clamps, bolts, lids, and system accessories before testing. • Release all air in system before testing. • Tighten Sta-Rite trap lids to 30 ft. lbs. (4.1 kg-m) torque for testing. • Water pressure for test must be less than 25 PSI (7.5 kg/cm2). • Water Temperature for test must be less than 100o F (38o C). • Limit test to 24 hours.
PAGE 4
NOTICE: Pump suction and discharge connections have molded in thread stops. DO NOT try to screw pipe in beyond these stops. service, all flooded suction systems must have gate valves in suction and discharge pipes. Fittings: Fittings restrict flow; for best efficiency use fewest possible fittings. Avoid fittings which could cause an air trap. Pool fittings must conform to International Association of Plumbing and Mechanical Officials (IAPMO) standards.
PAGE 5
ELECTRICAL All suction outlets must have correctly installed, screwfastened covers in place. Ground motor before connecting to electrical power supply. Failure to ground motor can cause severe or fatal electrical shock hazard. Testing and Certification Suction outlet covers must have been tested by a nationally recognized testing laboratory and found to comply with the latest ASME/ANSI Specification for Suction Fittings For Use in Swimming Pools, Spas, Hot Tubs, and Whirlpool Bathtub Applications.
PAGE 6
Remove Motor End Cover Ground wire must be a copper conductor. It should be the same size as the current-carrying wires to the motor, but not smaller than No. 12 AWG. Bond motor to pool structure. Use a solid copper conductor, size No. 8 AWG (8.4 sq. mm) or larger. Run wire from external bonding lug (see Fig. 3) to reinforcing rod or mesh. Connect a No. 8 AWG (8.4 sq.
PAGE 7
To Wire a Two-Speed Motor Dial Type Voltage Selector Wire the pump as shown in the diagram. Ground (Green) Ground Screw Low Speed 230 Volt Lines Voltage Change Dial Power Lead Terminals L2=COM L1=HI A=LOW A Back of motor with Terminal Board L2 Common Power Supply for Optional Timer.
PAGE 8
TABLE I – ELECTRICAL DATA - FUSING AND WIRING REQUIREMENTS Dura-Glas I and Max-E-Glas I Pool Pumps Single-Speed Models Model Motor HP Voltage/ Hz/Phase PE52C-180L PE5C-180L P2R5C-180L P2RA5C-179L PE52D-181L PE5D-181L PEA5D-180L PEAXSSD-180 P2R5D-181L P2RA5D-180L 71532 PE52E-182L PE5E-182L PEA5E-181L PEAXSSE-181 P2FA5E-180L P2R5E-182L P2RA5E-181L 71808 PEA5F-182L PEA6F-182L PEAXSSF-182 P2FA5F-181L P2RA5F-182L PE52F-183L PEAXSSG-183 P2RA6G-183L P2RAXG-183LS PEAAXSSG-184 PE6H-185L, LC 1/2 1/2 1/2 1/2 3/4 3
PAGE 9
OPERATION Replace trap cover on trap; turn clockwise to tighten cover. NOTICE: Tighten trap cover by hand only (no wrenches)! Pump should prime now. Priming time will depend on vertical length of suction lift and horizontal length of suction piping. If pump does not prime, make sure that all valves are open, suction pipe end is under water, pump suction is below water level, and that there are no leaks in suction pipe. See Troubleshooting Guide, Page 12. NOTICE: NEVER run pump dry.
PAGE 10
that have been overtightened or have taken a set and cannot be removed by hand. Lugs have been provided on the trap lid to use a lever or pry bar for loosening. 4. Cap inlet piping after draining to keep water out of the pipes. 5. Be sure motor is kept dry and covered. 9. Prime pump according to instructions on Page 9. PUMP SERVICE Pump should only be serviced by qualified personnel. Storage/Winterizing: For best results, use only genuine Sta-Rite factory parts. Explosion hazard.
PAGE 11
6. Remove motor canopy. 10. Place seal plate face down on flat surface and tap out ceramic seat (Figure 8). 11. Clean seal cavity in seal plate and clean motor shaft. Capacitor voltage can be dangerous. Before proceeding, short the capacitor terminals together with a screwdriver that has an insulated handle. Being careful not to touch capacitor terminals, loosen capacitor clamp and move capacitor to one side. 7. Hold shaft with 7/16" open-end wrench on motor shaft flats.
PAGE 12
TROUBLESHOOTING GUIDE water. If so, a “higher head” pump is needed. Electrical: 10. Pump may be running too slowly; check voltage at motor terminals and at meter while pump is running. If low, see wiring instructions or consult power company. Check for loose connections. Hazardous voltage. 11. Pump may be too hot. Can shock, burn, A. Check line voltage; if or cause death. less than 90% or more Disconnect power than 110% of rated before working on pump or motor. voltage consult a licensed electrician. B.
PAGE 13
REPAIR PARTS LIST DURA-GLAS POOL PUMP MAX-E-GLAS POOL PUMP 1/2 through 3 HP Models 1 2 3 4 5 6 20 8 7 9 17 19 18 10 14 13 16 Key No. 1 2 3 4 5 6 7 8 • 9 10 11 12 13 14 15 16 17 18 19 20 • • • • • • • Part Description Motor Screw, #10-32x1/2" Bonding Lug Water Slinger Seal Plate O-Ring Shaft Seal Clamp Clamp Knob Impeller Diffuser* Screw, #8-32x7/8" Washer, #8 Lock Diffuser O-Ring Tank Body 1/4” NPT Drain Plug Base w/Motor Pad* Motor Pad* Washer, Flat Screw, 3/8-16x1-3/4" Hex Hd.
PAGE 14
Variable Parts List (All other parts are common to all models) Dura-Glas I and Max-E-Glas I Pool Pumps SINGLE SPEED MODELS Model PE5C-180L PE52C-180L P2R5C-180L P2RA5C-179L PE52D-181L PE5D-181L PEA5D-180L PEAXSSD-180 P2R5D-181L P2RA5D-180L 71532 PE52E-182L PE5E-182L PEA5E-181L PEAXSSE-181 P2FA5E-180L P2R5E-182L P2RA5E-181L 71808 PEA5F-182L PEA6F-182L PEAXSSF-182 P2FA5F-181L P2RAXF-182LS PE52F-183L PEAXSSG-183** P2RA6G-183L P2RAXG-183L, LS PEAAXSSG -184** PE6H-185L, LC* HP Volts/Hz/Ph Motor Impeller Dif
PAGE 15
5" TRAP/ADAPTER ASSEMBLY PKG. 115 REPAIR PARTS LIST - 5" and 6" TRAPS* 1 Key No. 2 1 2 3 4 5 6 Trap Cover O-Ring - Cover Strainer Basket Trap Body Gasket Pipe Plug - 1/4" NPT (w/O-Ring) 7 Capscrew-5/16-18x1-1/4" 64SS(4) 8 Washer, Lock 5/16" 11SS(4) 9 Washer, Flat 5/16" 41SS(4) 3 4 5 6 6A 9 1844 0695 8 7 6" TRAP/ADAPTER ASSEMBLY PKG.
PAGE 16
*S413* S413 (Rev.