Specifications

© 2002 Alamo Group Inc.
Parts Section -91
Triumph Sickle Bar (Archive Book) 10/02
Feb. 2001
to
Replacement Part
S/N SB-Replacement
to
S/N SB-Replacement
HYDRAULIC MOTOR
8500 Series
Replacement Motor
Item Part No Part No. Qty. Description
02977120 ------------ 1
* Motor Only, 2.8 CID (Use 0447300 Motor Retrofit Kit)
0447300 ------------ -- * Motor Retrofit Kit (Motor 02977120 w/ items 18 thru 22)
------------ 02977279 1 * Motor Only, 2.2 CID (Use 0534400 Motor Retrofit Kit)
------------- 0534400 -- * Motor Retrofit Kit (Motor 02977279 w/ items 18 thru 22)
1 02977968 02977968 1 Retaining Ring, (included in Seal Kit)
2 02977969 02977969 1 Ball Bearing, (included in Seal Kit)
3 02977970 02977970 1 Retaining Ring, (included in Seal Kit)
4 02977971 02977971 1 Retaining Ring, (included in Seal Kit)
5 02977972 02977973 1 Washer, (included in Seal Kit)
6 02977973 02977973 1 Washer, Back-Up, (included in Seal Kit)
7 02977974 02977974 1 Pressure Seal, (included in Seal Kit)
8 02977975 02977975 1 Housing
9 02977976 02977976 1 Input Shaft
9A 02977981 02977981 1 Key
10 02977977 02977977 1 Drive Shaft
11 02977978 02977978 1 Seal, (included in Seal Kit)
12 02976884 ------------- 1 Geroler, For 02977120 Motor Only
------------- 02977979 1 Geroler, For 02977279 Motor Only
13 02978098 ------------- 1 End Cap, For 02977120 Motor Only
------------- 02976894 1 End Cap, For 02977279 Motor Only
14 02977980 02977980 7 Bolt, Hex Head
15 02978096 02978096 2 Poppet
16 02976893 02976893 1 Spacer Plate
17 02977967 02977967 1 Seal Kit (w/ Items 1, 2, 3, 4, 5, 6, 7 & 11)
18 00013300 00013300 4 Bolt, 1/2" (in P/N 0534400 & 0447300) Not Shown
19 02757800 02757800 2 Hyd Adapter Fitting (in P/N 0534400 & 0447300) Not Shown
20 02975300 02975300 1 Motor Adapter Flange (in P/N 0534400 & 0447300) Not Shown
21 02975301 02975301 1 Flywheel (in P/N 0534400 & 0447300) Not Shown
22 10010653 10010653 4 Bolt, 3/8" (in P/N 0534400 & 0447300) Not Shown
MOTORS SIZE IS 2.2 CID or 2.8 CID
NOTE: These are Replacement Motors and were not used in production, There are 2
different Motors, One had 2.8 CID (Used on D8500 Model CC System) & the other has
2.2 CID (Used on S8500 Model OC System) , Check which Motor needed before ordering
High Lighted Parts above. The rest of the parts are common Parts & will interchange
between the two Motors, The "D8500 & S8500 was a designation as to which tractor it
was mounted on. *These are replacement motors for earlier style, these cannot be
mounted without items 18 thru 22 to adapt these later style motors to older units