3109 LOADER Part No. F-4293C Published 01/11 OPERATOR’S MANUAL This Operator's Manual is an integral part of the safe operation of this machine and must be maintained with the unit at all times. READ, UNDERSTAND, and FOLLOW the Safety and Operation Instructions contained in this manual before operating the equipment. C01Cover RHINO ® 1020 S. Sangamon Ave. Gibson City, IL 60936 800-446-5158 Email: parts@servis-rhino.com © 2011 Alamo Group Inc. $0.
To the Owner/Operator/Dealer All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize the chance of accidents. BEFORE YOU START!!Read the safety messages on the implement and shown in your manual.
TABLE OF CONTENTS SAFETY SECTION .............................................................................................................. 1-1 General Safety Instructions and Practices ......................................................................................................... 1-2 Operator Safety Instructions and Practices ....................................................................................................... 1-4 Equipment Operation Safety Instructions and Practices .......
Hauling the Tractor and Implement .................................................................................................................. 4-42 Troubleshooting Guide ..................................................................................................................................... 4-43 MAINTENANCE SECTION .................................................................................................. 5-1 Lubrication Schedule ....................................................
SAFETY SECTION Safety Section 1-1
SAFETY General Safety Instructions and Practices SAFETY A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death.
SAFETY Never allow children to operate, ride on, or come close to the Tractor or Implement. Usually, 16-17 year-old children who are mature and responsible can operate the implement with adult supervision, if they have read and understand the Operator’s Manuals, been trained in proper operation of the tractor and Implement, and are physically large enough to reach and operate the controls easily. (SG-11) Never allow children or other persons to ride on the Tractor or Implement.
SAFETY Operator Safety Instructions and Practices Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Messages found in the Manual or on the Tractor and Implement. Learn how to stop the tractor engine suddenly in an emergency. Never allow inexperienced or untrained personnel to operate the Tractor or Implement without supervision.
SAFETY Prolonged operation may cause operator boredom and fatigue affecting safe operation. Take scheduled work breaks to help prevent these potentially impaired operating conditions. Never operate the Implement and Tractor in a fatigued or bored mental state which impairs proper and safe operation. (SG-32) Use extreme caution when getting onto the Implement to perform repairs, maintenance and when removing accumulated material. Only stand on solid flat surfaces to ensure good footing.
SAFETY Never grasp control levers when mounting the machine. (SBH-4) The Boom is designed only to position and operate the Bucket which is attached to it. Never attempt to lift, pull, or push other solid objects with the boom or bucket. Serious injury could result from a structural failure when the Boom is used for purposes other than those for which it was designed.
SAFETY Do Not operate this equipment in areas where insects such as bees may attack you and/or cause you to lose control of the equipment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to prevent insects from entering. If a tractor cab is not available, wear suitable clothing including head, face, and hand protection to shield you from the insects.
SAFETY Do not let the loader or attachment contact electrical power lines. Contact with electrical power lines can result in serious injury or electrocution. If the loader attachment contacts a power line remain in the tractor seat until the power has been shut off. Stepping off the tractor can permit electrical current to pass through the body resulting in electrocution. (SL-09) SAFETY Store the grapple bucket or bale spear attachment with the point(s) on the ground.
SAFETY Do not use an attachment that is not securely attached to the quick hitch, The attachment could fall resulting in severe crushing injuries or death to the operator or bystanders. Rotate both hitch pin levers down to the locked position. You should feel a firm resistance when locking the levers down. The pins must extend through the slots in the bottom of the attachment bracket. • Examine the fit between the quick hitch and the bottom of the attachment bracket.
SAFETY Know before you DIG. Call 888-258-0808 and request that all buried utilities locations be identified before digging in unfamiliar ground. Do not let the loader or attachment contact buried electrical power lines, utilities or gas lines. Contact with electrical power lines can result in serious bodily injury or electrocution. If the loader contacts a power line, remain in the tractor seat until the power has been shut off.
SAFETY Be particularly careful in transport. The Implement has raised and moved the center of gravity to the front of the Power Unit increasing the possibility of overturn and tipping forward. Turn curves or go up slopes only at low speed and using a gradual turning angle. Go up slopes with the Implement located uphill. Slow down on rough or uneven surfaces. (SPU-2) The center of gravity of a Power Unit equipped with a front-mounted Implement is shifted to the front and removes weight from the rear wheels.
SAFETY Connecting or Disconnecting Implement Safety Instructions and Practices SAFETY Do not stand or allow bystander or coworkers between the loader and the tractor while installing or disconnecting the loader from the tractor. Keep hands and body clear of the loader and the loader mounts. Serious injury or death can result from a person being crushed between the tractor and loader. (SL-03) Never allow anyone to get under the loader or attachment or to reach through the loader lift arms when raised.
SAFETY Transporting Safety Instructions and Practices Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.
SAFETY Lower the loader to the bed of the truck or trailer when transporting the tractor and loader with a truck. Measure to ensure the transport height does not exceed the legal limits. Contact with overhead obstructions or power lines can cause property damage or serious injury. (SL-34) SAFETY Before dismounting the tractor and loader, lower the loader to the ground or onto solid support blocks. Sudden dropping of the loader and attachment could result in serious injury.
SAFETY Never work under the Implement, the framework, or any lifted component unless the Implement is securely supported or blocked up to prevent sudden or inadvertent falling which could cause serious injury or even death. (SL-36) Never attempt to lubricate, adjust, or remove material from the Implement while it is in motion or while tractor engine is running. (SG-20) Periodically inspect all moving parts for wear and replace when necessary with authorized service parts.
SAFETY Avoid contact with hot surfaces of the engine or muffler. Use gloves and eye protection when servicing hot components. Contact with a hot surface or fluid can cause serious injury from burns or scalding. (SG-38) SAFETY Never allow anyone to get under the loader or attachment or to reach through the loader lift arms when raised. Serious injury could result from crushing or pinching by the loader or attachment.
SAFETY Decal Location NOTE: Rhino supplies safety decals on this product to promote safe operation. Damage to the decals may occur while in shipping, use, or reconditioning. Rhino cares about the safety of its customers, operators, and bystanders, and will replace the safety decals on this product in the field, free of charge (Some shipping and handling charges may apply). Contact your Rhino dealer to order replacement decals. SAFETY 3109 01/11 © 2011 Alamo Group Inc.
SAFETY SAFETY ITEM PART NO. QTY LEVEL DESCRIPTION 1. 55722 1 LOGO Rhino, Left 2. 55723 1 LOGO Rhino, Right 3. 55720 2 MODEL 3109 4. 52740 2 WARNING Oil Leaks 5. 52203 1 WARNING Lock Valve in Transport 6. 52204 1 INSTRUCT Loader Positions 7. D469 1 WARNING Loader Safety 8. D468 2 DANGER Crushing, Electrocution, Falling Hazard 9. D471 1 WARNING Handling Bales 10. D470 1 DANGER Use ROPS, Seatbelt, Rear Ballast 11. 03200347 * REFLCTR SMV Sign 12.
SAFETY Decal Location Rhino, Left SAFETY P/N 55722 Rhino, Right P/N 55723 MODEL NAME: 3109 P/N 55720 3109 01/11 © 2011 Alamo Group Inc.
SAFETY SAFETY WARNING! - DO NOT operate with oil leaks. -Inspect hoses regularly. Failure to inspect and replace worn hoses may allow them to rupture suddenly and violently, resulting in serious bodily injury or death from scalding, fire burn injury, or oil penetration. -Frayed, torn or crimped hoses may rupture and spray hot oil on operator causing serious injury. Oil may spray on hot tractor parts and catch fire resulting in severe injury, burn or death.
SAFETY Loader Safety D469 Crushing Hazard, Electrocution Hazard, Falling Hazard. D468 Crushing Hazard D471 3109 01/11 © 2011 Alamo Group Inc. Safety Section 1-21 SAFETY -Read, understand and follow the operation, warning, and safety instructions in the Operator’s Manual. -Equip tractor with ROPS (Roll Over Protection System) before installing or operating the loader. -Operate Loader only from operator’s seat with the seatbelt securely fastened around you.
SAFETY DANGER! - Use ROPS and seatbelt at all times. Add recommended rear ballast. Operate tractor at low speeds. Failure to comply may result in serious injury or death. SAFETY D470 Slow Moving Vehicle Decal. Keep SMV reflector clean and visible. DO NOT transport or operate without the SMV. P/N 03200347 Read Operator’s Manual! The operator’s manual is located inside this canister. If the manual is missing order one from your dealer. P/N 00776031 3109 01/11 © 2011 Alamo Group Inc.
SAFETY WARNING! - Crushing Hazard. (Located on the Quick Attach Device Only) P/N D516 3109 01/11 © 2011 Alamo Group Inc. Safety Section 1-23 SAFETY -To Avoid Serious Injury or Death Make sure attachment is securely attached to the loader. See Operator’s Manual for instructions. -Lock both levers down. Make sure pins are adequately extended through slots at the bottom of the attachment bracket and the tapered side of pin is firmly seated against attachments slots.
SAFETY Federal Laws and Regulations This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations SAFETY U.S. Public Law 91-596 (The Williams-Steiger Occupational and Health Act of 1970) OSHA This Act Seeks: “...
INTRODUCTION SECTION Introduction Section 2-1
INTRODUCTION INTRODUCTION This 3109 Loader is designed with care and built with quality materials by skilled workers. Proper assembly, maintenance, and operating practices, as described in this manual, will help the owner/operator get years of satisfactory service from the machine. The purpose of this manual is to familiarize and instruct. The Assembly Section instructs the owner/operator in the correct assembly of the Front End Loader using standard and optional equipment.
INTRODUCTION Engine Exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the state of California to cause cancer and birth defects or other reproductive harm. (SG-30) Never walk or work under any raised boom or bucket. The Boom could fall and cause serious bodily injury or death. Always lower the boom and bucket flat on the ground or support the Boom and bucket on safety stands. Unload all hydraulic actuators prior to performing any maintenance.
INTRODUCTION INTRODUCTION The Rhino 3109 Loader is designed for four-wheel drive tractors. They are intended to lift only loose materials that will fit in the bucket. All cylinders are double-acting. Parking stands support loader so tractor can be “driven in” for quick attaching. Front and rear, and left and right are determined by the normal direction of travel (the same as on your automobile). 3109 01/11 © 2011 Alamo Group Inc.
INTRODUCTION Attention Owner/Operator BEFORE OPERATING THIS MACHINE: 1. Carefully read the Operator’s Manual, completely understand the Safety Messages and instructions, and know how to operate correctly both the tractor and implement. 2. Fill out the Warranty Card in full. Be sure to answer all questions, including the Serial Number of the implement. Mail within 30 days of delivery date of this implement. 3. Record the Loader Model and Serial Numbers on the Warranty page.
ASSEMBLY AND CONNECTING THE LOADER SECTION Assembly Section 3-1
ASSEMBLY Assembly Instructions To avoid injury during installation of the loader attachment, do not allow bystanders within 10 feet of loader or attachment. Always wear safety glasses when removing or installing buckets. ASSEMBLY Always use a drift and hammer made of non-sparking material (a shot-filled mallet is recommended) to install or remove pins. A steel hammer or drift could generate flying metal fragments and result in injury.
ASSEMBLY Do not use an attachment that is not securely attached to the quick hitch, The attachment could fall resulting in severe crushing injuries or death to the operator or bystanders. Rotate both hitch pin levers down to the locked position. You should feel a firm resistance when locking the levers down. The pins must extend through the slots in the bottom of the attachment bracket. • Examine the fit between the quick hitch and the bottom of the attachment bracket.
ASSEMBLY Proper Ballasting and Wheel Spacing ASSEMBLY Spread front wheels to maximum distance. Spread rear wheels to maximum distance. Add rear wheel weight, rear ballast box or implement. Make sure there is 25% of total weight on rear axle. 3109 01/11 © 2011 Alamo Group Inc.
ASSEMBLY Dismounting Loader and Mounting Loader to Tractor To avoid injury during installation of loader: • Place loader bucket against barrier to restrict forward movement of loader. • Do not permit bystanders within 15 feet of loader. Loader must be equipped with a bucket or other optional attachment to dismount from tractor. 3109 01/11 © 2011 Alamo Group Inc. Assembly Section 3-5 ASSEMBLY When dismounting loader, maintain clearance between loader side frames and tractor hood and front axle.
ASSEMBLY ASSEMBLY Dismounting Loader 1. Locate tractor and loader on firm level ground. 2. Rotate parking stands from storage position to operation position by removing hair pins and clevis pins. Reinstall clevis pin and hair pin when parking stands are in operation position. See Figure Asm-L-0167. 3. Level and lower bucket to ground. Rotate bucket down slightly to remove pressure on hitch pins (See Figure Asm-L-0168). 4. Remove lynch pins and hitch pins from mounting. 5.
ASSEMBLY Installing Bucket Level Indicator 1. Attach indicator guide tube to cylinder pin. Position guide tube to inside of boom, Figure Asm-L-0169. 2. Slide level indicator rod through guide tube, Figure Asm-L-0170. Attach other end of rod with 1/8 x 1” cotter pins and 3/8” flat washers. Attach lower end of rod to attachment ear. 3109 01/11 © 2011 Alamo Group Inc. Assembly Section 3-7 ASSEMBLY Locate tractor and loader on level surface.
ASSEMBLY Attaching Pin on Bucket Always wear safety glasses when removing or installing buckets. ASSEMBLY Always use a drift and hammer made of non-sparking material (a shot-filled mallet is recommended) to install or remove pins. A steel hammer or drift could generate flying metal fragments and result in injury. Always wear safety glasses when using a hammer to remove or install pins. Material buckets can be installed using tools ordinarily available.
ASSEMBLY Assembling Quick Attach Device Quick attach device can be installed using tools ordinarily available. Torque all hardware to specifications listed in loader operator’s manual. Shut off the tractor engine and engage the tractor brakes during installation. Only quick attach, skid steer compatible attachments can be used with the quick attach device. Pin on style attachments can be used on the loader, but necessitate removal of the quick attach device and relocation of the bucket level indicator. 1.
ASSEMBLY Installing Quick Attach Device ASSEMBLY Always use a drift and hammer made of non-sparking material (a shot-filled mallet is recommended) to install or remove pins. A steel hammer or drift could generate flying metal fragments and result in injury. Always wear safety glasses when using a hammer to remove or install pins. 1. Fasten quick attach device to lower boom arms and bucket tilt cylinders using anti-rotation pins, 3/8” x 3/4” shoulder bolts, and 3/8” lock nuts (supplied with loader).
ASSEMBLY When Connecting an Attachment to the Loader Quick Hitch Never walk or work under or allow any person to be underneath a raised loader or attachment. • Examine the fit between the quick hitch and the bottom of the attachment bracket. The pins must extend through the slots in the bottom of the attachment bracket. The tapered side of each pin must be firmly wedged against the surface of the slot on the bottom of the attachment bracket.
ASSEMBLY ASSEMBLY 5. On level ground, tilt the attachment down 90 degrees and lower it to the ground. Lower the loader further to slightly raise the front of the tractor of the tractor off the ground. Drive the tractor in reverse while the attachment is on the ground for 20-30 feet to insure the attachment does not disconnect. If the attachment disconnects during this process, discontinue the use of attachment and contact your dealer.
OPERATION SECTION Operation Section 4-1
OPERATION RHINO 3109 LOADER OPERATION INSTRUCTIONS OPERATION READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2) Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad.
OPERATION 1. Standard Equipment and Specifications Specifications will vary with tire size, hydraulic system and bucket used. Specifications are given for a loader equipped with a 68” pin on bucket, external hydraulic system of 10 GPM with engine operating at 2600 RPM and relief setting of 2500 PSI. 30-50 HP 2500 PSI/ 10 GPM 1320 lbs. 4410 lbs. 3030 lbs. 980 lbs. 4.97 seconds 3.42 seconds 2.47 seconds 3.19 seconds 10 GPM 2500 PSI (A) (B) (C) (D) (E) (F) (G) (H) (I) 111” 107 93” 24” 42° 62” 20° 5.
OPERATION 2. Operator Requirements OPERATION DO NOT use drugs or alcohol immediately before or while operating the Tractor and Implement. Drugs and alcohol will affect an operator’s alertness and coordination and therefore affect the operator’s ability to operate the equipment safely.
OPERATION Always read carefully and comply fully with the manufacturer’s instructions when handling oil, solvents, cleansers, and any other chemical agent. (SG-22) Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health. (SG-23) Prolonged operation may cause operator boredom and fatigue affecting safe operation. Take scheduled work breaks to help prevent these potentially impaired operating conditions.
OPERATION OPERATION Repeated or substantial breathing of hazardous dusts, including crystalline silica, could cause fatal or serious respiratory disease including silicosis. Concrete, masonry, many types of rock, and various other materials contain silica sand. California lists respirable crystalline silica as a substance known to cause cancer. Operation of this equipment under certain conditions may generate airborne dust particles that could contain crystalline silica.
OPERATION 3. Tractor Requirements Operate this Equipment only with a Tractor equipped with an approved rollover-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS. (SG-7) Tractor Requirements and Capabilities • • • ASABE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt. Tractor Safety Devices .................
OPERATION 3.3 Tractor Ballast OPERATION Before operating tractor and loader, add sufficient counterweight so a minimum of 25% of the total weight is on the rear axle. Total weight includes weight of: tractor, loader, rated load in bucket, and counterweight. Rated load is lift capacity at full height at 500mm forward of bucket pivot point (See Standard Equipment and Specifications).
OPERATION 4.1 Boarding the Tractor Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) Never grasp control levers when mounting the machine. (SBH-4) Never allow passengers to ride on the tractor or attached equipment. Riders can easily fall off and be seriously injured or killed from falling off and being ran over. It is the operator’s responsibility to forbid all extra riders at all times. OPS-L- 0023 4.
OPERATION 5. Starting the Tractor OPERATION Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health. (SG-23) Start tractor only when properly seated in the Tractor seat. Starting a tractor in gear can result in injury or death. Read the Tractor operators manual for proper starting instructions.
OPERATION 6. Pre-Operation Inspection and Service Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good working order. (SG-21) Before each use, a pre-operation inspection and service of the implement and tractor must be performed.
OPERATION 6.1 Tractor Pre-Operation Inspection/Service OPERATION Refer to the tractor operator’s manual to ensure a complete pre-operation inspection and scheduled service is performed according to the manufacturers recommendations.
OPERATION Before operation, a complete inspection and service is required to ensure the loader is in a good and safe working condition. Damaged and/or broken parts should be repaired and/or replaced immediately. To ensure the loader is ready for operation, conduct the following. OPS-L-0027 The operator’s manual and safety signs affixed on the unit contain important instructions on the safe and proper use of the equipment.
OPERATION LOADER BOOM ASSEMBLY • • • • OPERATION • Inspect condition of each arm section weldment Ensure all pins are in place. Ensure all bolts and screws are properly installed. Check condition of bushings at boom pivot points. Ensure each hydraulic cylinder is installed and retained correctly. Ensure the proper size pins are used to retain the cylinders in place and are secured properly. OPS-L-0005_B HYDRAULIC LINE INSPECTION • • • • Check for hydraulic leaks along hoses, cylinders and fittings.
OPERATION Tractor PRE-OPERATION Inspection Tractor ID#______________________ Make____________________ Date___________________________ Shift_____________________ Condition at Start of Shift Item Specific Comments if not O.K.
OPERATION FRONT END LOADER PRE-OPERATION Inspection Front End Loader ID#_______________Make____________________ OPERATION Date_____________________________Shift____________________ Before conducting the inspection, make sure the tractor engine is off, all rotation has stopped and the tractor is in park with the parking brake engaged. Make sure the Loader is resting on the ground or securely blocked up and all hydraulic pressure has been relieved.
OPERATION 7. Driving the Tractor and Loader This Implement may be wider than the Tractor. Be careful when operating or transporting this equipment to prevent the Implement from running into or striking sign posts, guard rails, concrete abutments or other solid objects. Such an impact could cause the Implement and Tractor to pivot violently resulting in loss of steering control, serious injury, or even death. Never allow the Implement to contact obstacles.
OPERATION OPERATION Use extra care when turning or stopping. Allow for increased length and weight of added loader. The loader adds five to six feet of length in front of the tractor and significant weight. Allow extra distance when stopping or turning. Do not allow loader or attachment to contact solid objects. (SL-07) Safe tractor transport requires the operator possess a thorough knowledge of the model being operated and precautions to take while driving with an attached implement.
OPERATION 8. Operating the Tractor and Loader Do not attempt to lift loads in excess of loader capacity. Operating loader on a hillside is dangerous. Extreme care is recommended. Keep bucket as low as possible. Do not raise the loader on a hillside. Do not transport across a slope with a raised loader. When the loader is raised, the center of gravity of the tractor and loader is raised increasing the potential for the tractor to tip over.
OPERATION Do Not operate this equipment in areas where insects such as bees may attack you and/or cause you to lose control of the equipment. If you must enter in such areas, use a tractor with an enclosed Cab and close the windows to prevent insects from entering. If a tractor cab is not available, wear suitable clothing including head, face, and hand protection to shield you from the insects.
OPERATION Do not use an attachment that is not securely attached to the quick hitch, The attachment could fall resulting in severe crushing injuries or death to the operator or bystanders. Rotate both hitch pin levers down to the locked position. You should feel a firm resistance when locking the levers down. The pins must extend through the slots in the bottom of the attachment bracket. • Examine the fit between the quick hitch and the bottom of the attachment bracket.
OPERATION OPERATION Know before you DIG. Call 888-258-0808 and request that all buried utilities locations be identified before digging in unfamiliar ground. Do not let the loader or attachment contact buried electrical power lines, utilities or gas lines. Contact with electrical power lines can result in serious bodily injury or electrocution. If the loader contacts a power line, remain in the tractor seat until the power has been shut off.
OPERATION Never leave the Implement and Power Unit unattended while the Implement is in the raised position. Accidental operation of a lifting lever or a hydraulic failure may cause the implement to suddenly fall causing serious injury or possible death to anyone who might inadvertently be under the Implement. Lower the implement carefully to the ground. Do not put hands or feet under lifted components. (SPU-3) Make sure the hydraulic quick disconnects are fully seated into the connections.
OPERATION THE OPERATOR MUST COMPLETELY UNDERSTAND HOW TO OPERATE THE TRACTOR AND IMPLEMENT AND ALL CONTROLS BEFORE ATTEMPTING TO OPERATE. The operator must read and understand the Safety and Operation Sections of the implement and tractor operator’s manuals. These manuals must be read and explained to any operator who cannot read. Never allow someone to operate the implement and tractor without complete operating instructions.
OPERATION A level bucket throughout the lifting cycle resists bucket lift and increases breakaway effort. NOTE: Do not be concerned if the bucket is not completely filled during each pass. Maximum productivity is determined by the amount of material loaded in a given period of time. Time is lost if two or more attempts are made to fill the bucket on each pass. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-25 OPERATION Lift and roll back of bucket will increase efficiency because...
OPERATION LIFTING THE LOAD OPERATION When lifting the load, keep the bucket positioned to avoid spillage. Loader has mechanical self leveling of attachment in both raise and lower cycle. Attachment can be adjusted by using bucket cylinders. CARRYING THE LOAD Position bucket just below tractor hood for maximum stability and visibility, whether bucket is loaded or empty. 3109 01/11 © 2011 Alamo Group Inc.
OPERATION Use extreme care when operating loader on a slope, keep bucket as low as possible. This keeps center of gravity low and will provide maximum stability. DUMPING THE BUCKET Lift bucket high enough to clear side of vehicle. Move tractor in as close as possible to side of vehicle, then dump bucket. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-27 OPERATION When transporting the load, keep bucket as low as possible, to avoid tipping, in case a wheel drops in a rut.
OPERATION LOWERING THE BUCKET OPERATION After bucket is dumped, back away from vehicle while lowering and rolling back bucket. 3109 01/11 © 2011 Alamo Group Inc.
OPERATION OPERATING WITH FLOAT CONTROL During hard surface operation, keep bucket level and put lift control in float position to permit bucket to float on working surface. If hydraulic down pressure is exerted on bucket, it will wear faster than normal. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-29 OPERATION Float will also prevent mixing of surface material with stockpile material. Float position will reduce the chance of surface gouging when removing snow or other material.
OPERATION LOADING FROM A BANK Choose a forward gear that provides sufficient ground speed for loading. OPERATION Exercise caution when undercutting high banks. Dirt slides can be dangerous. Load from as low as possible for maximum efficiency. Loader lift and breakaway capacity diminish as loading height is increased. Side cutting is a good technique for cutting down a big pile.
OPERATION Another method for large dirt piles is to build a ramp approach to the pile. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-31 OPERATION It is important to keep the bucket level when approaching a bank or pile. This will help prevent gouging the work area.
OPERATION PEELING AND SCRAPING OPERATION Use a slight bucket angle, travel forward and hold lift control forward to start the cut. Make a short 5 to 8 foot angle cut and break out cleanly. With bucket level, start a cut at notch approximately 2 inches deep. Hold depth by feathering bucket control to adjust cutting lip up or down. When front tires enter the notch, adjust lift cylinder to maintain proper depth. Make additional passes until desired depth is reached.
OPERATION LOADING LOW TRUCKS OR SPREADERS FROM A PILE For faster loading, minimize angle of turn and length of run between pile and spreader. Back grade occasionally with a loaded bucket to keep working surface free of ruts and holes. Also, hold lift control forward so full weight of bucket is scraping ground. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-33 OPERATION Do not roll bucket over and attempt to backgrade.
OPERATION BACKFILLING OPERATION Approach pile with a level bucket. Poor methods actually move no more dirt and make it more difficult to hold a level grade. Do not use bucket in dumped position for bulldozing. This method, shown above, will impose severe shock loadings on dump linkage, bucket cylinder and tractor. 3109 01/11 © 2011 Alamo Group Inc.
OPERATION Leave dirt in bucket. Dumping on each pass wastes time. 3109 01/11 © 2011 Alamo Group Inc. Operation Section 4-35 OPERATION Operate tractor at right angles to ditch. Take as big a bite as tractor can handle without lugging down.
OPERATION OPERATION Leave dirt which drifts over side of bucket for final cleanup. Pile dirt on high side for easier backfilling on a slope. HANDLING LARGE HEAVY OBJECTS 1. Using front end loaders for handling large heavy objects such as large round or rectangular bales, logs and oil drums is not recommended. 2. Handling large heavy objects can be extremely dangerous due to: • Danger of tractor rolling over. • Danger of up-ending tractor.
OPERATION 8.2 Operating Bale Spear Operate the bale spear using extreme caution. Sharp points on bale spear can cause serious injury or death. Because of size and weight of large bales, extreme care must be taken in handling them. Be aware of forces acting on stacked bales due to gravity and keep workers far from zones of potential hazard from shifting or falling bales. DO NOT ALLOW BYSTANDERS! Keep bale spear and loader boom clear of overhead lines.
OPERATION OPERATION Carry bales as low to the ground as possible to allow maximum visibility and avoid tipping. 8.3 Shutting Down the Implement Park the tractor on a level surface, place the transmission in park or neutral and apply the parking brake, lower the attached implement to the ground, shut down the engine, remove the key, and wait for all motion to come to a complete stop before exiting the tractor. OPS-L- 0014 9. Loader Storage Never allow children to play on or around Tractor or Implement.
OPERATION Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly. Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment.
OPERATION OPERATION Inherent hazards of operating the tractor and implement and the possibility of accidents are not left behind when you finish working in an area. Therefore, the operator must employ good judgement and safe operation practices when transporting the tractor and implement between locations. By using good judgement and following safe transport procedures, the possibility of accidents while moving between locations can be substantially minimized.
OPERATION Extreme caution should be used when transporting the tractor and implement on public roadways. The tractor must be equipped with all required safety warning features including a SMV emblem and flashing warning lights to alert drivers of the tractor’s presence. Remember that roadways are primarily designed for automotive drivers and most drivers will not be looking out for you, therefore, you must look out for them.
OPERATION 10.2 Hauling the Tractor and Implement OPERATION Before transporting a loaded tractor and implement, measure the height and width dimensions and gross weight of the complete loaded unit. Ensure that the load will be in compliance with the legal limits set for the areas that will be traveled through. OPS-U- 0024 Use adequately sized and rated trailers and equipment to transport the tractor and implement. Consult an authorized dealer to determine the proper equipment required.
OPERATION 11. Troubleshooting Guide POSSIBLE CAUSE POSSIBLE REMEDY Loader slow or will not lift and/or dump Hydraulic oil too heavy. Change to proper oil. Oil filter plugged. Hydraulic pump worn. Oil line restricted or leaking. Cylinder leaks internally. Faulty relief valve (tractor). Clean or replace filter. Repair or replace pump. Check all hoses and tubes for leaks, damage or restrictions. Replace damaged or restricted hoses or tube oil lines. Inspect, clean, repair or replace valve.
OPERATION OPERATION PROBLEM POSSIBLE CAUSE REMEDY Insufficient lift capacity Load is greater than boom lift capacity. Improper hydraulic pump operation. Internal lift cylinder leakage. Check loader specifications. Improper hydraulic valve operation. Repair or replace pump. Replace any worn parts and install a seal repair kit. See “Cylinder Service”. Repair or replace valve. Excessive wear on bucket cutting edge Bucket is riding on cutting edge instead of wear runners.
MAINTENANCE SECTION Maintenance Section 5-1
MAINTENANCE READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2) MAINTENANCE Never interfere with factory-set hydraulic calibrations. Any change in calibration could cause a failure of the equipment and may result in injury. (SBH-13) Always maintain the safety signs in good readable condition.
MAINTENANCE Do Not fill fuel tank while engine is running. Refuel only after engine has cooled down. If fuel is spilled, move machine away from the area of the spill and avoid creating any source of ignition until the fuel has evaporated. (SBH-49) Avoid contact with hot surfaces including hydraulic oil tanks, pumps, motors, valves and hose connections. Relieve hydraulic pressure before performing maintenance or repairs. Use gloves and eye protection when servicing hot components.
MAINTENANCE Lubrication Schedule MAINTENANCE Before operating your Loader, take the time to inspect and repair any damage to the machine or tractor. Only a minimum of time and effort is required to regularly maintain this machine to provide long life and trouble free operation. Lubricate all grease fittings: one at each end of lift boom arms and one at rod and base ends of each lift and bucket cylinders. NOTE: Fully retract bucket to a comfortable height to grease bucket/loader boom joint.
MAINTENANCE Daily Maintenance Regular maintenance of your loader and hydraulic system will insure maximum loader efficiency and long life. 1. Check fluid level of tractor hydraulic system before starting each day’s operation. If necessary, add hydraulic oil as recommended in your tractor operator’s manual. 2. Daily, unless conditions justify more frequent greasing, lubricate all twelve grease fittings; one at each end of lift boom arms and one at rod and base ends of each lift and bucket cylinder. 4.
MAINTENANCE Cylinder Service MAINTENANCE Loader cylinders are designed to be reliable and easy to service. If a cylinder should malfunction during warranty period, return complete cylinder assembly, without disassembling, to your authorized service department or contact your authorized service department for instructions. Unauthorized disassembly of a cylinder in warranty period will VOID WARRANTY.
MAINTENANCE Lift and Bucket Cylinder Reassembly Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly. 1. Place rod seal (3) into groove inside cylinder head. Note: Lips of seal (3) must be face inward and seal must be firmly seated in groove. 3. Place o-ring (7) with back-up washer (6) in groove on outside of head. Back-up washer must be on rod side. 4.
MAINTENANCE MAINTENANCE 1. Store loader with attachment securely attached. 2. Place dust caps on hydraulic quick couplers. 3. Do not remove attachment from stored loader. 4. Do not allow children to play on or around loader. 3109 01/11 © 2011 Alamo Group Inc.
MAINTENANCE Proper Torque for Fasteners The chart lists the correct tightening torque for fasteners. When bolts are to be tightened or replaced, refer to this chart to determine the grade of bolts and the proper torque except when specific torque values are assigned in manual text. RECOMMENDED TORQUE IN FOOT POUNDS UNLESS OTHERWISE STATED IN THE MANUAL* 3109 01/11 © 2011 Alamo Group Inc.
MAINTENANCE MAINTENANCE 3109 01/11 © 2011 Alamo Group Inc.
MAINTENANCE MAINTENANCE 3109 01/11 © 2011 Alamo Group Inc.
RHINO LIMITED WARRANTY 1. 2. LIMITED WARRANTIES 1.01. Rhino warrants for one year from the purchase date to the original non-commercial, governmental, or municipal purchaser (“Purchaser”) and warrants for six months to the original commercial or industrial purchaser (“Purchaser”) that the goods purchased are free from defects in material or workmanship. 1.02.
TO THE OWNER/OPERATOR/DEALER To keep your implement running efficiently and safely, read your manual thoroughly and follow these directions and the Safety Messages in this Manual. The Table of Contents clearly identifies each section where you can easily find the information you need. The OCCUPATIONAL SAFETY AND HEALTH ACT (1928.51 Subpart C) makes these minimum safety requirements of tractor operators: REQUIRED OF THE OWNER: 1.
3109 LOADER 3109-SOM-01/11 Printed U.S.