User's Manual

Copyright © 2016 Alarm.com | www.alarm.com | v1.0
5
Simon XT/XTi/XTi-5 LTE/IP Module | Installation Guide
---- Update 2WTTS
Press OK to force an update of the
thermostat information shown on the
touch screen (2WTTS). Note that these
updates may take several minutes to
complete. To speed up the process, go
into System Programming. This puts the
panel in high-speed communication mode
with the touch screen.
---- Remove From 2WTTS
To remove the association between the Z-
Wave thermostat and the touch screen
(2WTTS). This will hide the Thermostat
page on the 2WTTS.
---- Last Temp. Read
For troubleshooting only. Shows how
many unsuccessful attempts were made
by the LTE module at trying to
communicate with the Z-Wave
thermostat. A low number of 0 or 1 is
normal.
-- Request Weather Update
Press OK if the weather forecast is not
showing on the touch screen (2WTTS).
1
All Image Sensor menus are only available when an Image Sensor daughterboard
has been connected to the module. An Image Sensor daughterboard is required
to enable Image Sensor functionality. An interactive Alarm.com account with an
Image Sensor service plan is required for image capabilities and features.
2
Refer to the emPower
TM
installation instructions and guides on the Alarm.com
Dealer Site for more information on Z-Wave enrollment and troubleshooting.
Table 4: XTi and XTi-5 Interactive Services Menu
Menu
Description
System Programming +
Installer Code
Scroll to Programming and enter the
Installer Code.
- Interactive Services
Select Interactive Services.
-- Module Status
Provides status and troubleshooting
information for the LTE module.
-- Image Sensor
1
Enroll, troubleshoot and configure Image
Sensors. This menu can also be used to
retrieve images from the enrolled Image
Sensors.
---Status
1
View signal strength, PIR, battery and
other information about each Image
Sensor enrolled.
----Set PIR Sensitivity
1
View and configure the PIR sensitivity for
the Image Sensor.
---Privacy
1
Remove all Image Sensor images currently
stored on the XTi or XTi-5 panel. (This
does not affect image storage on the
Alarm.com online account.)
--- Add
1
Enroll the Image Sensor by inserting
batteries or resetting.
---Image List
1
View list of images captured by the Image
Sensor(s) on the system and request to
have specific images sent to the panel for
local viewing.
--- Test
1
Put the Image Sensor in PIR Test Mode
(LED on sensor illuminates when
activated) or request an “Installer Peek-In
Now” to test image capture.
--- Delete
1
Delete Image Sensors from the panel.
--Set Dealer Logo
Send the dealer logo to the panel and
touch screen. (Only available for dealers
who have set up this feature with
Alarm.com.)
-- Weather Update
Request a Weather Update if the weather
forecast is not showing on the XTi or XTi-5
touch screen. To speed up the process,
stay in Programming. This keeps the panel
in high-speed communication mode with
the touch screens.
-- Z-Wave
2
Used to add, remove, and troubleshoot Z-
Wave devices and networks. To control Z-
Wave devices via the Alarm.com website
and smart phone apps, you will also need
to enable Z-Wave services on the account.
--- Add Device
2
Add Z-Wave devices to the module’s
network. Make sure the device you are
trying to add is powered up and within 3
to 6 feet of the Simon XTi or XTi-5 panel.
Read the manufacturer’s instructions on
what button to press on the device to
enroll it.
--- Remove Device
2
Remove an existing Z-Wave device, or to
“reset” a Z-Wave device that was
previously learned into a different Z-Wave
network, before you can learn it into the
LTE module.
---Update 2WTTS
Press Update 2WTTS to force an update of
the thermostat, lights or locks information
shown on the touch screen (2WTTS). Note
that these updates may take several
minutes to complete.
----Thermostats
View thermostat data and update/remove
thermostats from display on the panel and
touch screens.
----Lights
Update the lights list shown on the panel
and touch screens.
----Locks
Update locks list shown on panel and
touch screens and pair locks with their
door contact sensor.
--- Advanced
2
Provides additional functionality for
advanced Z-Wave troubleshooting and
configuration.
---- Rediscovery
2
Network rediscovery allows the system to
determine the most efficient
communication patch between Z-Wave
devices. (During this process the Z-Wave
network is busy and cannot respond to
other commands.)
---- Replicate Mode
2
Initiates replicate mode on the panel.
---- Send Node Info
2
For advanced use only. Do not use unless
directed to do so by Alarm.com.
---- Refresh Thermostat
2
Requests updated thermostat data.
--Advanced Menu
This menu houses advanced LTE/IP
module tasks.
---Auth. Code
Requests an authorization code from
Alarm.com for use on the Image Sensor
Installer Test Site.
(www.alarm.com/imagesetup).