USER MANUAL ANLEITUNG / DEUTSCH WP-24 Fernbedienung für CB-Funkgeräte
Inhaltsverzeichnis Lieferumfang Eigenschaften B.
Eigenschaften Fernbedienung 1 2 3 4 Empfänger 5 6 1. Kanal aufwärts 4. Kanal abwärts 2. Funktionstaste 5. Mikrofonempfindlichkeit 3. Sendetaste 6. LED Anzeige 1. Kanal aufwärts Drücken Sie die Taste, um zum nächsthöheren Kanal zu wechseln. 2. Funktionstaste Die Funktionstaste aktiviert bzw. deaktiviert ASQ. 3. Kanal abwärts Drücken Sie die Taste, um zum nächstniedrigeren Kanal zu wechseln. 4.
B. Einrichtung Batterie einlegen Das WP24 verwendet eine Knopfzelle vom Typ CR2032. Öffnen Sie das Batteriefach auf der Rückseite (Deckel gegen Uhrzeigersinn drehen). Legen Sie die Batterie in das Fach ein, die "+" Seite muss nach oben zeigen. Schließen Sie danach den Deckel wieder (im Uhrzeigersinn drehen). Deckel öffnen Batterie einlegen ("+" oben) Deckel schließen Reichweite Das WP24 hat eine (Sicht-) Reichweite von ca. 7 Metern.
Installation Fernbedienung Schritt 1: Installieren Sie die Halterungsklammer wie in der Zeichnung unten angegeben. Achten Sie darauf, dass die glänzende Seite der Klammer nach Innen zeigt. Schritt 2: Ziehen Sie das Montageband so fest wie möglich an und rasten Sie es dann in 2 vorgesehene Löcher ein. Fixieren Sie das Montageband mit 2 Schrauben. Verwenden Sie eine Schere, um das überstehende Montageband zu entfernen.
Installation des Empfängers Schalten Sie Ihr CB-Funkgerät aus. Nun schließen Sie das WP24 an die Mikrofonbuchse des CB-Funkgeräts an. Die LED Anzeige blinkt beim Start 5x rot und wechselt dann zu grün. Wenn die LED Anzeige grün leuchtet, ist das Gerät empfangsbereit. Installation des externen Mikrofons Das externe Mikrofon sollte in der Nähe ihrer Sitzposition installiert werden. Wir empfehlen, dass Mikrofon an einer Säule an der Fahrerseite, an der Sonnenblende oder an der Mittelkonsole zu befestigen.
USER MANUAL Manual / English WP-24 remote for CB radios
Table of Contents A. Introduction Included in this package Features B. Preparation Installing Battery Range Install Remote Mounting Install the Receiver Install the Remote microphone Pairing A. INTRODUCTION Thank you for purchasing a YOSAN 2.4GHz Wireless PTT radio. Properly used, this YOSAN product will give you many years of reliable service. Your WP24 wireless remote control is designed to reproduce functions of a standard hand held microphone using wireless technology.
FEATURES remote Receiver 1 2 3 4 5 6 1. Channel Up 4. Channel Down 2. Function 5. microphone Gain control Volume 3. Push to Talk 6. LED Indicator 1. Channel Up key This key allows selection of the operating channel in increments. By keeping this key pressed, the quick channel selection mode will be enabled. 2. Function key This function follow your standard microphone. If already preprogrammed was "INS" or "ASQ" . This "f" function key will be done. 3.
B.PREPARATION Installing Battery The WP24 operates from a standard CR2032 Coin button battery. To insert the battery, back side the battery cover open and insert the battery. Insert battery by insert it into the compartment with the +side upwards. Refit the battery cover and clockwise fully forward until it stop. Cover open Insert Coin battery (+ side up) cover lock Range The WP24 has a line-of-sight range of around 7 meters depending on the installation.
Install the transmitter Step 1. Once you have chosen where to install, please insert steering wheel clamp as shown below. Ensure that the shiny side part of the steering wheel clamp faces inside the handle. Step 2. Pull as much as possible on the steering wheel clamp as shown in the figure below, and then insert it into the holes so that it is fixed to a tight Use the two screws packed together to move tightly as shown in the figure below. Use a pair of scissors to cut the remaining clamping wheel clamp.
Install the Receiver The your transceiver power off, and insert the microphone lead of WP24 to your transceiver and turn to connector ring in clockwise to lock it. The two color LED will be red blinking 5 times and than change to green LED lights up. If this green LED lights up is successful the receiver will work correctly.