AE355M Scanner Bedienungsanleitung 1
Wichtige Hinweise Sicherheitshinweise Vor der Benutzung dieses Scanners beachten Sie bitte die folgenden Hinweise: Warnung Albrecht übernimmt keine Garantie, dass dieses Gerät wasserdicht ist. Zur Vermeidung von Feuer, Stromschlag und Schäden setzen Sie das Gerät nicht Regen oder Feuchtigkeit aus. Gesetzeskonforme Benutzung eines Scanners In den meisten europäischen Ländern ist die Benutzung eines Scanners zum Abhören von Funkdiensten, die für die Öffentlichkeit freigegeben sind, erlaubt.
Inhalt Sicherheitshinweise ..................................................................................................... 2 Warnung ...................................................................................................................... 2 Gesetzeskonforme Benutzung eines Scanners .......................................................... 2 Informationen zu Ihrem neuen AE355M Scanner ....................................................... 5 Ausstattungsmerkmale ..........................
Hinweise zu Close Call ..................................................................................... 28 Kategorie Private ................................................................................................... 28 Frequenzen und Kanäle programmieren .......................................................... 28 Kanal programmieren ....................................................................................... 29 Programmierte Frequenz löschen („000.0000“ programmieren) ............
Informationen zu Ihrem neuen AE355M Scanner AE355M ist mit 7 vorprogrammierten Suchlaufbereichen zur Überwachung von Funkkommunikationsdiensten wie Notfalldiensten (Rettungsdienst, Feuerwehr, Polizei und andere Notfallorganisationen), Freenet und PMR446, kommerziellen VHF- und UHF-Funk, Air-Band, Seefunk, CB-AM und 10-m-Band FM Amateurfunk ausgestattet. Diese Suchlaufbereiche enthalten bereits werksseitig vorprogrammierte, häufig benutzte Frequenzen.
» AIR - 3.480 werksseitig programmierte Frequenzen, welche das gesamte Flugfunk-Band abdecken, 108.000 bis 136.9916 MHz. » MARINE - 57 werksseitig programmierte Frequenzen, welche das gesamte internationale VHF Seefunk-Band abdecken. Hinweis: Die Kategorien Air und Marine haben eine gemeinsame Taste – AIR/MARINE. Mit Tastendruck schalten Sie zwischen den beiden Kategorien um. Weitere Informationen erhalten Sie in den nachstehenden Abschnitten.
23 Suchbänder - Deutscher Bandplan 2 Drücken Sie BAND/STEP zur Auswahl eines der 23 Bänder zur Suche (deutscher Bandplan nach Werkseinstellung): Band Bereich (MHz) Schritt (kHz) Modus 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 25.00000 - 29.99500 30.00000 - 49.99500 50.00000 - 79.99500 80.00000 - 82.99500 83.00000 - 84.01000 AM FM FM FM FM 84 - 87 84.01500 - 87.
Internationaler Bandplan 1 Für die Benutzung in anderen Ländern ist möglicherweise der britische / internationale Bandplan 2 interessant: 8 Band Bereich (MHz) Schritt (kHz) Modus 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 84 - 87 108 - 137 137 - 138 138 - 144 144 - 146 146 - 156 156 - 157 157 - 158 158 - 160 160 - 162 162 - 162 162 - 174 406 - 440 440 - 450 450 - 466 466 - 470 470 - 512 806 - 960 25.00000 - 29.99500 30.00000 - 49.99500 50.00000 - 79.99500 80.00000 - 82.99500 83.00000 - 84.01000 84.
Der Scanner hat folgende Empfangsdaten Frequenzband Empfindlichkeit (nominal) 12 dB SINAD 25.000 - 27.995 0,4 µV 28.000 - 69.9950 0,2 µV 70.0000 - 87.2950 0,2 uV 108.0000 - 136.9916 0,4 uV 137.0000 - 147.9950 0,2 uV 148.0000 - 174.0000 0,2 uV 406.0000 - 512.0000 0,3 uV 806.0000 - 960.0000 0,4uV Frequenzband Brummen, Rauschen, Störabstand (nominal) 25.000 - 27.995 48 dB 28.000 - 87.2950 43 dB 108.0000 - 136.9916 48 dB 137.0000 – 174.0000 43 dB 400.0000 - 512.0000 42 dB 806.
Lieferumfang Scanner • AE355M Scanner • Teleskopantenne zum Einstecken • Netzteil • Fahrzeugadapter 12 V DC mit Stecker für Zigarettenanzünder • 12 V DC Anschlusskabel mit „offenen Enden“ zur Festverkabelung mit anderen 12 V Netzwerken (wie Boot, Wohnwagen oder Heimanschluss Ihres Scanners) • Mobile Halterung • Schrauben • Bedienungsanleitung • Andere Dokumentationen Sollte etwas fehlen, so wenden Sie sich bitte direkt an Ihren Fachhändler.
• Betreiben Sie den Scanner in einem Grenzbereich oder möchten Sie den Empfang verbessern, so benutzen Sie eine optionale Albrecht Scanner-Feststation-Antenne für Multi-Band-Abdeckung (erhältlich in unserem Webshop oder im örtlichen Fachhandel). • Hat die optionale Antenne kein Kabel, dann benutzen Sie 50-70 Ohm Koaxialkabel zum Anschluss. Ein entsprechender Steckeradapter für BNC-Standard ist für optionale Antennen möglicherweise notwendig.
Halterung benutzen. 3. 4. Bohren Sie die notwendigen Löcher und schrauben Sie die Halterung mit den mitgelieferten Schrauben an. VORSICHT: Bohren Sie keine Löcher in Airbags. Bohren Sie nicht ins Armaturenbrett, wenn Sie nicht wissen, was sich dahinter befindet. Montieren Sie den Scanner erst auf der Halterung, nachdem Sie die Verkabelung auf der Rückseite vorgenommen haben.
Scanner Überblick AE355M Frontlende TASTE BESCHREIBUNG HOLD Drücken Sie diese Taste, um das Scannen oder die Suche zu unterbrechen und auf der aktuellen Frequenz zu bleiben. „HOLD“ wird im Display angezeigt. Drücken Sie erneut HOLD, um den Scan fortzusetzen. UP Drücken Sie diese Pfeiltasten zur: • manuellen Suche im Haltemodus aufwärts oder abwärts durch die Frequenzen. oder DOWN • Richtungsänderung der Suche im Suchmodus.
TASTE BESCHREIBUNG FRN/PMR Drücken Sie diese Taste zum Scannen der vorprogrammierten Freenet- (FRN) und PMR-446 Frequenzen. Mit Tastendruck durchlaufen Sie die Frequenzen in folgender Reihenfolge: • Freenet (FRN)/PMR – beide aktiviert • nur Freenet (FRN) (PMR deaktiviert) • nur PMR (Freenet deaktiviert) • Keines aktiv (Freenet und PMR deaktiviert) HINWEIS: Der Bereich Freenet (FRN) hat 100 PRIVATE Kanäle.
TASTE BESCHREIBUNG AIR/MARINE Drücken Sie diese Taste zum Scannen des Flugfunks (Air)- und Marinebandes. Mit Tastendruck durchlaufen Sie die Frequenzen in folgender Reihenfolge: • Air/Marine - beide aktiviert CB AM/FM SEARCH L/O • nur Air (Marine deaktiviert) • nur Marine (Air deaktiviert)• Keines aktiv (Air und Marine deaktiviert) Drücken Sie diese Taste zum Scannen des CB AM und Amateurbandes (CB FM).
ELEMENT BESCHREIBUNG Volume/Clock Lautstärkeregler/ Uhr Drehen Sie diesen Regler, um den AE355M einzuschalten und die Lautstärke einzustellen. SQ (Squelch) Rauschsperre Stellen Sie mit SQ den Scan-Grenzwert ein. Überwachen Sie einen einzelnen Kanal im Scan-Haltemodus, dann eliminieren Sie mit SQ die Hintergrundgeräusche, wenn kein Signal anliegt. LCD Das Flüssigkristalldisplay (LCD) zeigt den aktuellen Kanal oder seine Frequenz an. Es werden ebenfalls Modus, Status und Bereich angezeigt.
Bedienungshinweise AE355M Scanner Einstellung Squelch einstellen Zur Squelch-Einstellung gehen Sie wie folgt vor: 1. Drehen Sie SQ ganz nach links. Sie hören jetzt das Rauschen der offenen Rauschsperre. 2. Drehen Sie SQ langsam nach rechts, bis das Rauschen verschwindet. Dies ist der Grenzpunkt, an dem das eingehende Signal nur etwas stärker ist als das Rauschen, das damit die Rauschsperre öffnet. 3. Stellen Sie die Lautstärke auf ein komfortables Niveau ein.
Das entsprechende Bereichssymbol blinkt während des Scans. Wird eine aktive Frequenz gefunden, dann stoppt der Scanner auf dieser Frequenz. Endet die Übertragung, dann wartet der Scanner 2 Sekunden auf eine neue Übertragung. Wird keine neue Übertragung gefunden, wird der Scan fortgesetzt. Drücken Sie UP, um den Scan manuell fortzusetzen. Mehrere aktive Bereiche werden der Reihe nach gescannt.
HINWEIS: Freenet hat 100 PRIVATE Kanäle. Diese vom Benutzer programmierten Kanäle werden nach den vorprogrammierten Kanälen gescannt. Drücken Sie mehrmals AIR/MARINE, um die Bereiche in folgender Reihenfolge zu durchlaufen: 1. Air/Marine 2. Air 3. Marine 4. Keine Drücken Sie mehrmals CB AM/FM, um die Bereiche in folgender Reihenfolge zu durchlaufen: 1. CB AM und 10-m-Amateurband (CB FM) 2. CB AM 3. 10-m-Amateurband (CB FM) 4.
Hinweise zum Scannen von Speicherbereichen Um dies zu erreichen: Tun Sie dies: Scan starten Drücken Sie eine Bereichstaste, das entsprechende Symbol blinkt und „SCAN“ läuft als Laufschrift über das Display. Der Scan stoppt automatisch auf einem aktiven Kanal und die Frequenz wird angezeigt (außer bei übersprungenen Kanälen, hierzu an anderer Stelle mehr). Nach Beendigung der Übertragung wird weiter gescannt. Hinweis: Sie müssen Kanäle in den Bereich PRIVATE programmieren, bevor Sie sie scannen können.
Um dies zu erreichen: Tun Sie dies: Weiter scannen, nachdem der AE355M auf einem aktiven Kanal gestoppt hat Bleibt der AE355M auf einem aktiven Kanal stehen, den Sie weder abhören noch umgehen möchten, dann drücken Sie . Sie scannen mit der nächsten Frequenz weiter. Andere Kategorie zum Wählen Sie eine der folgenden Methoden: Scannen wählen • Mit gehen Sie durch die Frequenzen und Kategorien.
Display-Anzeigen Dieser Abschnitt zeigt typische Displays: Speicherbereiche scannen Das Display zeigt, dass AE355M einen angezeigten Bereich aktiv scannt. „SCAN“ läuft als Laufschrift von rechts nach links und der gescannte Bereich blinkt. Das Display zeigt, dass der Scanner im HALTEMODUS ist, um die Frequenz 149.025 des Bereichs „Freenet“ zu überwachen. Bänder durchsuchen Mit Tastendruck auf BAND/STEP zeigt das Display den zu durchsuchenden Bandbereich an.
Besondere Funktionen Der AE355M Scanner ist mit einer Reihe besonderer Funktionen ausgestattet: • Überspringen (Sperren) von Kanälen/Frequenzen („Lock Out“) • Close Call (Suche im Nahbereich) • Privater Speicherbereich PRIVATE • Programmierung von Frequenzen in programmierbare Speicherbereiche • Programmiersperre • Auswahl der Frequenzschritte • Uhrzeit Ausblenden (auch Überspringen der Sperren von Kanälen/Frequenzen genannt) Manchmal bleibt der Scanner auf einem bestimmten Kanal oder einer Fre
löscht der Scanner die erste umgangene Frequenz. Das Umgehen einer Frequenz in einem beliebigen Speicherbereich oder in einem Suchband blendet die gleiche Frequenz auch in allen anderen Bereichen und Suchbändern aus (sofern sie dort noch einmal vorkommt). Solch eine Frequenz ist jedoch nicht betroffen, wenn sie als Kanal auf einem Speicherplatz abgespeichert wurde. Sie können nur alle Kanäle oder Frequenzen in den Bereichen Private, EMG, Freenet (FRN), PMR und Marine ausblenden.
Suche nach permanent ausgeblendeten Kanälen oder Frequenzen Der Scanner stoppt nicht bei umgangenen Kanälen oder Frequenzen; zur Suche und Anzeige umgangener Kanäle oder Frequenzen drücken Sie HOLD, dann UP oder DOWN, um die Kategorie manuell zu durchsuchen. „L/O“ erscheint zur Anzeige der Umgehung.
Close Call ® Die Funktion Close Call ermöglicht die Suche nach starken Signalen in der Nähe Ihres Standortes. Diese Signale können von einem Funktaxi, Linienbus, Polizeiwagen, einer Feuerwehr oder sonstigen Funkquelle in der Nähe kommen. zur Aktivierung der Close Call Funktionen in nachstehender Drücken Sie Reihenfolge: 1. 2. 3. Close Call nicht stören Close Call Priorität Close Call aus Halten Sie gedrückt, um nur Close Call zu aktivieren.
der Menüoptionen aufwärts oder abwärts. Nach Auswahl einer Menüoption drücken Sie PROG, um sie einzustellen. 5. Drücken Sie BAND/STEP, um zur vorherigen Option zurückzukehren oder , um das Close Call Menü zu verlassen. drücken Sie Close Call (C-C) Bandoptionen einstellen In diesem Menü wählen Sie, welche Bänder mit Close Call überprüft werden: Band Name Frequenz (MHz) b1 Lo VHF Low Band 25.0000 - 87.2950 b2 Air AIR Band 108.0000 - 136.9916 b3 Hi VHF High Band 137.0000 - 174.
Hinweise zu Close Call Um dies zu erreichen: Tun Sie dies: Scan für Close Call Übertragungen, während andere Bereiche oder Bänder abgehört werden . Das Close Call Symbol wird Drücken Sie angezeigt. Alle 2 Sekunden gibt es eine kurze Unterbrechung des Scans, während eine Übertragung in der Nähe gesucht wird. Frequenz speichern, die mit Close Call gefunden wurde 1. Findet der Scanner ein Signal in der Nähe mit Close Call, dann springt er zu dieser Frequenz, zeigt sie jedoch nicht an.
• EMG • Freenet (FRN) • Private Jede angezeigte Frequenz für diese Bereiche kann in den Scanner programmiert werden und Frequenzen, die nicht angezeigt werden, können mit dem Suchmodus sowie manuelles Scannen der vorprogrammierten Bereiche aufgefunden werden. Weiterhin veröffentlichen Websites und Magazine (z.B. Siebel-Verlag / Deutschland) Listungen örtlicher Funkfrequenzen.
Drücken Sie die Taste für den Bereich Kategorie, den Sie programmieren möchten. In diesem Beispiel wurde FRN/PMR gedrückt. Das Display schaltet zwischen zwei Anzeigen um. Das erste Display zeigt, dass Kanal 6 der niedrigste verfügbare Kanal im Bereich Freenet (FRN) ist (drücken Sie oder , um einen anderen Kanal zu wählen); das zweite Display zeigt, dass die Frequenz 149.025 zur Programmierung zur Verfügung steht. Drücken Sie PROG.
Programmierte Frequenz löschen („000.0000“ programmieren) Die einfachste Methode zum Löschen einer von Ihnen programmierten Frequenz ist, diese mit einer Null-Frequenz (000.0000) zu überschreiben. Drücken Sie HOLD, um den Scan zu unterbrechen und drücken Sie PROG. HOLD wird angezeigt und CH blinkt. Halten Sie L/O für 2,5 Sekunden gedrückt. Die Frequenz ändert sich zu 000.0000 und CH blinkt weiterhin. Drücken Sie die Bereichstaste für den zu löschenden Kanal.
Drücken Sie PROG. Das Display zeigt eine Null-Frequenz in diesem Kanal. Drücken Sie erneut die Bereichstaste, um den Scan des Bereichs fortzusetzen. Programmiersperre Der AE355M ist mit einer Programmiersperre zur Vermeidung einer versehentlichen oder unbefugten Programmierung ausgestattet. Halten Sie PROG für 2,5 Sekunden zur Aktivierung/Deaktivierung dieser Sperrfunktion gedrückt.
5. oder wählen Sie die Schritte für das Flugfunk - Band als 8.33 kHz Mit oder 12.5 kHz. Dann drücken Sie PROG zum Verlassen, der Scanner kehrt in die Bandsuche zurück. (Die meisten Flugfunkstationen arbeiten noch in einer 25 kHz Rasterung (also 2 x 12.5 kHz). Das 8.33 kHz Raster ist weltweit in der Einführungsphase und kann 3 Stationen unterbringen, wo früher nur 1 Station möglich war). Uhrzeit Die Uhr des Scanners wird immer angezeigt, wenn Sie die Funkfunktionen ausschalten.
Störungserkennung und Beseitigung PROBLEM LÖSUNGSVORSCHLAG Scanner arbeitet nicht Versuchen Sie eine dieser Optionen: • Überprüfen Sie die Anschlüsse auf beiden Seiten des Netzteils. Überprüfen Sie, ob die 230 V Steckdose funktioniert. Benutzen Sie im Zweifel eine andere Steckdose. Schlechter Empfang Scan wird nicht unterbrochen • Überprüfen Sie die Anschlüsse auf beiden Seiten des DC-Kabels oder des Fahrzeugadapters. • Überprüfen Sie, ob die Sicherung durchgebrannt ist.
Scan wird nicht gestartet Suche startet nicht PROG-Taste funktioniert nicht Versuchen Sie eine dieser Optionen: • Drücken Sie die Bereichstaste erneut. • Stellen Sie die Rauschsperre ein. • Programmieren Sie Frequenzen in die Bereiche, bevor Sie sie benutzen (gilt für den Bereich PRIVATE). • Überprüfen Sie, ob alle Kanäle ausgeblendet sind. Es ist möglich, dass keine der programmierten Frequenzen gerade aktiv ist. Versuchen Sie die Bandsuche. • Stellen Sie die Rauschsperre ein.
Pfeifen (Birdies) Alle Funkgeräte können unerwünschte Signale oder Birdies empfangen. Stoppt Ihr Scanner im Suchmodus, Sie hören jedoch nichts, so empfangen Sie möglicherweise einen Birdie. Birdies sind interne, in der Elektronik des Empfängers, erzeugte Signale. Ist die Störung nicht zu stark, können Sie sie mit Rechtsdrehung von SQ möglicherweise ausschalten. Alternativ drücken Sie SEARCH, um die Suche fortzusetzen.
Technische Spezifikationen Abmessungen: 132 mm (B) x 142 mm (T) x 42 mm (H) Gewicht: 640 g Betriebstemperatur: -20 ºC bis + 60 ºC Spannungsversorgung: DC 13,8 V (10,8…15,6 V DC) • Speicherbereiche: 8 Bereiche insgesamt (7 vorprogrammierte Bereiche + 1 privater Bereich) • Abhängig von Bandplan: Vorprogrammiertes EMG-Band (4-m-Band mit 20-kHz-Abstand einschließlich 15 kHz Versatz im deutschen Bandplan 2) oder 24 vorprogrammierte Moschee-Frequenzen (britischer und internationaler Bandplan 1) plus 100 programm
Weitere hilfreiche Informationen Service-Adresse und Download Hier finden Sie die Einzelheiten zum Download unserer Sammlung von Servicehinweisen und Dokumentationen. Unsere technischen Dokumentationen werden regelmäßig überarbeitet. Laden Sie die neueste Version von Bedienungsanleitungen, technischen Dokumenten und ebenfalls die zweisprachige Konformitätserklärung und Servicehinweise oder häufig gestellte Fragen (FAQs) herunter bei: http://service.alan-electronics.
Europäische Garantiebestimmungen Die europäischen Garantiebestimmungen gelten für alle Verkäufe in Europa. Die Garantie deckt Hardware- und Softwarefunktionen gemäß den europäischen Richtlinien ab.
CE-Konformitätserklärung Hiermit wird erklärt, dass unser Produkt / herewith we declare that our product Empfangsgerät für Funkdienste (Scanner) Radio Receiver for Kommunikation services AE 355 M den folgenden europäischen Normen entspricht: / is in conformity to following European Standards EU-Richtlinien / EU directives 73/23/EEC (LVD); 2004/108/EG (EMC) and 99/5/EEC (R&TTE), EN 301 489-1 V 1.8.1, EN 301 489-5 V1.2.1, EN 301 489-13 V.1.2.1, EN 301 489-15 V1.2.1 (EMC), EN 300 086-2 V.1.2.
AE355M Scanner Owner’s Manual 1
Important Information Precautions Before you use this scanner, please observe the following: Warning Albrecht does not guarantee this unit to be waterproof. To reduce the risk of fire, electrical shocks or damage to the unit do not expose this unit to rain or moisture. Legal use of a scanner In most European countries it is allowed to use a scanning receiver for listening to radio services, which are free for public listening.
Table of Contents Precautions ................................................................................................................... 2 Warning ........................................................................................................................ 2 Legal use of a scanner ................................................................................................. 2 About your new AE355M Scanner ...............................................................................
Programming a Channel ....................................................................................30 Program Lock Feature............................................................................................33 Select Step Frequency ...........................................................................................34 Clock Mode ............................................................................................................34 Troubleshooting Guide ............................
About your new AE355M Scanner The AE355M comes with 7 service banks for monitoring radio communication services like EMG (rescue, fire brigade, police and other emergency organizations, Freenet & PMR446, Commercial VHF & UHF Radio, Air Band, Marine Radio, CB & 10 m Band AM and FM frequencies. These service banks contain already factory pre-programmed often used frequencies. In addition the AE355M has 23 separate band searches.
Pressing this key will toggle between the banks. Additional information is provided in later sections. » CB AM: 600 Factory-programmed CB AM frequencies between 25.000 and 27.995 MHz. » Amateur Band (Display: CB FM): 400 Factory-programmed FM 10m band amateur frequencies between 28.000 and 29.995 MHz. Note: The CB AM and Amateur Band (CB FM) banks share a single key – CB AM/FM. Pressing this key will toggle between the banks. Additional information is provided in later sections.
23 Search Bands - German Band Plan 2 Press BAND/STEP to select one of the 23 bands to search (German Band Plan as factory setting): Band Range (MHz) Step (kHz) Mode 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 25.00000 - 29.99500 30.00000 - 49.99500 50.00000 - 79.99500 80.00000 - 82.99500 83.00000 - 84.01000 AM FM FM FM FM 84 - 87 84.01500 - 87.
For use in other countries the UK / International Band Plan 2 may be as well interesting: 8 Band Range (MHz) Step (kHz) Mode 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 84 - 87 108 - 137 137 - 138 138 - 144 144 - 146 146 - 156 156 - 157 157 - 158 158 - 160 160 - 162 162 - 162 162 - 174 406 - 440 440 - 450 450 - 466 466 - 470 470 - 512 806 - 960 25.00000 - 29.99500 30.00000 - 49.99500 50.00000 - 79.99500 80.00000 - 82.99500 83.00000 - 84.01000 84.01500 - 87.29500 108.00000 - 136.99166 137.00000 - 137.
The Scanner has following receiving data Frequency Band Sensitivity (Nominal) 12 dB SINAD 25.000 - 27.995 0.4 µV 28.000 - 69.9950 0.2 µV 70.0000 - 87.2950 0.2 uV 108.0000 - 136.9916 0.4 uV 137.0000 - 147.9950 0.2 uV 148.0000 - 174.0000 0.2 uV 406.0000 - 512.0000 0.3 uV 806.0000 - 960.0000 0.4uV Frequency Band Hum and Noise (Nominal) 25.000 - 27.995 48 dB 28.000 - 87.2950 43 dB 108.0000 - 136.9916 48 dB 137.0000 – 174.0000 43 dB 400.0000 - 512.0000 42 dB 806.000 - 960.
Included in your Scanner Package • AE355M scanner • Telescopic plug-in antenna • AC adapter • Vehicle power adapter 12 V DC with cigarette lighter plug • 12 V DC power cord with “open ends” for hard-wiring power from other 12 V supply networks (like boat, caravan or home power supply to your scanner) • Mobile mounting bracket • Screws • Owner’s manual • Other printed materials If any of these items are missing or damaged, immediately contact your place of purchase.
Installing the AE355M Scanner Home Use (Desktop Installation) 1. Insert the DC plug end of the AC Adapter into the DC 13.8V jack on the rear panel. 2. Plug the AC Adapter into a standard 230V AC wall outlet. 3. Plug the telescopic antenna into the ANT connector. Extend the antenna to its full height. For frequencies higher than 400 MHz, shortening the antenna may improve the reception. Use the desktop stand (fold out from bottom of unit) for a better viewing and operating angle.
Permanent Installation Permanently installing the AE355M scanner into a vehicle may be a legal problem in cars, which are used in public traffic. We recommend to use a permanent installation only in justified cases e.g. in caravans on fixed places, garden houses, boats etc. equipped with 12 V battery or solar power supply networks. Permanent installation involves two main steps physically installing the scanner and physically connecting the power supply.
3. 4. Connect the BLACK wire of the DC power cord to the negative side of the vehicle (usually the chassis). Caution: In vehicles with a positive ground, the RED wire connects to the chassis and the BLACK wire connects to the accessory contact in the fuse box. Insert the DC plug into the DC 13.8V jack on the back panel.
Scanner Operation Overview AE355M Front Panel KEY PURPOSE HOLD Press this key to stop scanning or searching and to remain on the current frequency. “HOLD” displays on the screen. Press HOLD a second time to resume scanning. UP Press these directional keys to: • Manually search up or down for frequencies while in Hold mode. or DOWN • Change direction of a search during Search mode. • Quickly search up or down for frequencies or for longer than 1 second) (hold while in Hold mode.
KEY PURPOSE FRN/PMR Press this key to scan the Freenet (FRN) and PMR bands. Pressing this key cycles through the frequencies in the following order: • Freenet (FRN)/PMR - both activated • Freenet (FRN) only (turn off PMR bank) • PMR only (turn off Freenet bank) • None active (turn off both Freenet and PMR banks) NOTE: The Freenet (FRN) bank has 100 PRIVATE channels. These user programmed channels are scanning after the preprogrammed channels if the Freenet is selected.
KEY PURPOSE CB AM/FM Press this key to scan the CB AM and Amateur Band (CB FM) bands. Pressing this key cycles through the frequencies in the following order: • CB AM / Amateur Band (CB FM) bands both activated SEARCH L/O 16 • CB AM only (turn off Amateur Band (CB FM) bank) • Amateur Band (CB FM) only (turn off CB AM bank) • None active (turn off both CB AM / Amateur Band (CB FM) banks) Press the SEARCH key to search for active frequencies within a selected band range.
ITEM PURPOSE Volume/Clock Volume Control/Clock Switch Turn this control clockwise to turn the AE355M unit on. Continue turning this control clockwise to adjust the volume. SQ Squelch Control Adjust SQ to set the scan threshold. When you are monitoring a single channel in Scan Hold Mode, adjust SQ to eliminate the background noise heard in the absence of an incoming signal. LCD The Liquid Crystal Display (LCD) shows the current channel or its frequency.
Using your AE355M Scanner Set up Adjusting Squelch To Adjust Squelch - 18 1. Turn SQ completely counterclockwise. You should hear open squelch noise. 2. Turn SQ clockwise slowly until the sound disappears. This is the threshold point at which the incoming signal is just slightly stronger than the noise which will open the squelch. 3. Adjust the volume to a comfortable listening level.
Operating Modes The AE355M comes ready pre-configured to receive typical radio communication services in Germany. For this purpose, the radio has 2 different factory installed “Band Plans 1 or 2” which let you receive the radio communication services with the optimized country specific channel spacings and other preference settings. We strictly recommend not to change the band plan settings unless you are in other European countries.
NOTE: The EMG (Mosque bank in UK) has 100 PRIVATE channels. These user-programmed channels are scanned after pre-programmed channels. Pressing FRN/PMR more than once will cycle through the banks in this order: 1. Freenet (FRN)/PMR 2. Freenet (FRN) 3. PMR 4. None NOTE: The Freenet bank has 100 PRIVATE channels. These user-programmed channels are scanned after pre-programmed channels. Pressing AIR/MARINE more than once will cycle through the banks in this order: 1. Air/Marine 2. Air 3.
Scanning Service Bank Tips If You Want to do This - Here’s How - Begin scanning Press any service bank key; the bank label flashes and the “SCAN” message moves across the display screen. Scanning automatically stops on an active channel and displays that frequency (except for locked-out channels which will be covered later in this guide). It will stay on that channel until the transmission ends. Note: You must program channels into the PRIVATE bank before you can later scan it.
If You Want to do This - Here’s How - Select a different bank to scan Use one of the following two methods: • Use the key to move through frequencies and banks. • Deactivate the bank(s) you do not want to listen to, leaving only the desired band active. Searching Band Tips If You Want to Do This 22 Here’s How - Begin searching Press the BAND/STEP key. The screen displays the last known searched band and then begins searching for an active frequency in that band.
Screens This section shows typical screen displays: Scanning Banks This screen shows AE355M is actively scanning a displayed bank. “SCAN“ scrolls from right to left across the screen and the scanned bank will flash. This screen shows that the scanner has been put on HOLD to monitor frequency 149.025 on the “Freenet” bank. Searching Bands When BAND/STEP is pressed this screen displays the band range to be searched. Press BAND/STEP again (or UP/DOWN within 3 seconds) to see other band ranges.
Special features The AE355M scanner boasts of several special features: • Lock Out Channels/Frequencies • Close Call • Private Bank • Program Frequencies into Programmable Banks • Program Lock • Select Step Frequency • Clock Mode Lock Out Channels / Frequencies Sometimes the scanner may stop on a particular channel or frequency because of noise or other unwanted transmissions. This feature lets you lock out channels and frequencies you don’t want to scan.
Lock Out Tips If You Want to Do This Here’s How - Temporary Lock Out While on a channel or frequency press L/O once. The scanner beeps and temporarily locks out that channel and displays “T L/O.” If the scanner was not in Hold mode it then resumes scanning. If the scanner was in Hold mode it does not resume scanning until one of the following actions is taken: • Press HOLD again to release the Scan Hold function. Scanning resumes on that bank.
Restoring a Single Locked-Out Channel or Frequency 1 Press the appropriate bank key (PRIVATE, EMG, FRN/PMR, AIR/MARINE and CB AM/FM) to start scanning the bank that has the channel or frequency you want to unlock. 2 Press HOLD to stop scanning. (“HOLD” must appear on the screen.) 3 Use UP or DOWN keys to find the specific locked out channel or frequency (in this example Channel 12, which displays “L/O”). Press L/O.
Close Call ® The Close Call feature enables you to search for strong signals close to your location. These signals could be from a nearby police car or fire engine or other radio source. key activates the Close Call functions in the following order: Pressing the 1. Close Call Do Not Disturb 2. Close Call Priority 3. Close Call Off Pressing and holding the key activates Close Call Only mode. Close Call Priority Repeatedly press until the Close Call Priority icon displays.
Setting Close Call (C-C) band Options Use this menu to select which bands get Close Call checks: Band Name Frequency (MHz) b1 Lo VHF Low Band 25.0000 - 87.2950 b2 Air AIR Band 108.0000 - 136.9916 b3 Hi VHF High Band 137.0000 - 174.0000 b4 UHF UHF Band 406.0000 - 512.0000 b5 800 800MHz Band 806.0000 - 960.0000 1. From Step 4 previously select C-C band. The first band selection displays: 2. Scroll up or down to select bands for Close Call to monitor. Press PROG.
Close Call Tips If You Want To - Here’s How - Scan for Close Call Transmissions while Scanning other Banks/Bands key. The Close Call icon Press the displays. Every two seconds there will be a break in the scanner audio as it searches for a nearby transmission. Save a Frequency Found Through Close Call 1. The scanner finds a nearby signal through Close Call it jumps to that frequency but does not display it. It does however display the band number and flashes “Found” 2.
Any displayed frequency for these banks can be programmed into the scanner and frequencies not currently displayed can be located through the Search mode and through manually scanning the preprogrammed banks. In addition websites and magazines (e.g. Siebel-Verlag / Germany ) publish listings of local radio station frequencies. NOTE: The Air/Marine and CB AM/Amateur Band (CB FM) banks are not programmable. ”Error ” displays if you try to program a frequency into either of these two banks.
The screen cycles between two displays. The first screen shows that channel 6 is the lowest available channel on the Freenet (FRN) bank (press or to select a different channel) and the second screen shows that frequency 149.025 is available to be programmed. Press PROG. The scanner programs the frequency into the indicated channel and then goes into SCAN HOLD mode. Press HOLD to release the Hold and continue scanning the rest of the programmed channels starting with the channel you just programmed.
Press the bank containing the channel you wish to clear. The screen displays the first programmable channel for that bank. If that channel displays 000.0000, press or until the channel/ frequency you wish to clear appears. (In this example channel 6 contains frequency 149.025 MHz.) The screen cycles between two displays. The first screen shows that channel 6 on the Freenet (FRN) bank (149.025) is selected. The second screen shows that the null frequency (000.0000) is ready to be programmed. Press PROG.
Program Lock Feature The AE355M has a Program Lock feature to prevent accidentally programming entries or unauthorized programming. Press and hold the PROG key for longer than 2.5 seconds to toggle Program Lock on and off. Program Lock is available in the following modes: • Scan/Scan Hold • Band Search/Band Search Hold • Programming • Close Call When Program Lock is turned on the scanner displays “ON Prg.Loc” and then returns to previous mode.
Select Step Frequency You can change the frequency steps (channel spacing). Selected step affects both band search and Close Call. For air band selected step affects more air service bank. If the scanner displays for 3 seconds while selecting step frequency mode the scanner returns to Band Search. 1. 2. 3. 4. 5. Press SEARCH or BAND/STEP key to start Band Search. Press and hold BAND/STEP key until the scanner displays the current steps and the confirmation tone is generated.
Troubleshooting Guide PROBLEM SOLUTION Scanner won’t work Try one of these options: • Check the connections at both ends of the AC adapter. Check whether the 230 V power distribution socket is turned on. If not, use another AC wall outlet. Bad Reception Scan won’t stop • Check the connections at both ends of the DC cord or Vehicle Power Adapter. • Check to see if the fuse is blown. Make sure the car DC socket is powered. • Make sure the power switch is turned on.
PROBLEM Search won’t start (cont.) PROG key won’t work SOLUTION • Adjust the Squelch Control. • Check the antenna connection. Stop scan or search. General Product Care Turn the scanner off before disconnecting the power. Always press each keypad button firmly until you hear the entry tone for that key entry. Location If strong interference or electrical noise is received relocate the scanner or its antenna away from the source of the noise.
• cable again. Release buttons - the present Band Plan number appears • • • Select the desired band plan with or Press PROG to store the band plan The Scanner will display the clock and can be switched on as normal. Please note that any Band Plan change will modify the factory preset channel steps settings of all bands and the memory contents of the EMG band between (German) Band Plan 2 and UK / International settings of Band Plan 1.
Technical Specifications Size: 132mm (W) x 142mm (D) x 42mm (H) Weight: 640g Operating Temperature: – 20ºC to + 60ºC Power Requirements: DC 13.8V (10.8…15.6 VDC) • Banks: 8 banks total (7 Service banks / 1 Private bank) • Depending on Band plan: Preprogrammed EMG band (4 m Band with 20 kHz spacing incl. 15 kHz offset in German Band Plan 2) or 24 Preprogrammed Mosque frequencies (UK + International Band Plan 1) plus 100 programmable channels.
Service Address (for scanners sold in Germany) PST professional support technologies GmbH Breitscheider Weg 117a D - 40885 Ratingen Technical Hotline e-mail: alan-service@ps-tech.de Hotline: 01805-012204 The service hotline can be reached from the German fixed telephone network (14 Cent per minute) or mobile networks (45 Cent or less per minute). In any case we recommend to contact the hotline before returning any scanner. In many cases problems can already cleared by a simple phone call.
© Alan Electronics GmbH 2011 CE Declaration of Conformity Hiermit wird erklärt, dass unser Produkt / herewith we declare that our product Empfangsgerät für Funkdienste (Scanner) Radio Receiver for communication services AE 355 M den folgenden europäischen Normen entspricht: / is in conformity to following European Standards EU-Richtlinien / EU directives 73/23/EEC (LVD); 2004/108/EG (EMC) and 99/5/EEC (R&TTE), EN 301 489-1 V 1.8.1, EN 301 489-5 V1.2.1, EN 301 489-13 V.1.2.1, EN 301 489-15 V1.2.
Scanner AE355M Guide d'utilisation 1
Informations importantes Précautions Lisez les consignes suivantes avant d'utiliser ce scanner : Avertissement Albrecht ne garantit pas que cet appareil soit étanche. N’exposez pas cet appareil à la pluie et l'humidité pour réduire les risques d'incendie, de chocs électriques et de dommages. Utilisation légale d'un scanner Dans la plupart des pays européens, l’utilisation d’un récepteur à balayage pour écouter des services de radio publics gratuits est autorisée.
Table des matières Précautions .................................................................................................................. 2 Avertissement .............................................................................................................. 2 Utilisation légale d'un scanner ..................................................................................... 2 À propos de votre nouveau scanner AE355M ............................................................
Programmation de fréquences et canaux ......................................................... 29 Programmation d'un canal ................................................................................ 30 Suppression d'une fréquence programmée (programmation « 000,0000 »).... 32 Fonction de verrouillage de Programme ............................................................... 33 Sélection du pas des fréquences .......................................................................... 33 Mode horloge .
À propos de votre nouveau scanner AE355M L’AE355M est livré avec 7 bancs de service pour les services d’écoute de contrôle de communication radio tels qu'EMG (secours d'urgence, pompiers, police et autres organisations de secours d'urgence, Freenet & PMR446, Radio Commerciale VHF et UHF, Air Band, Radio maritime, CB & fréquences de bande AM et FM de 10 m. Ces bancs de service contiennent déjà les fréquences souvent utilisées préprogrammées en usine.
» MARINE - 57 fréquences programmées en usine qui couvrent toute la Bande Marine VHF internationale. Remarque : Les bancs Air et Marine partagent une seule touche AIR/MARINE. En appuyant sur cette touche permet de basculer entre les bancs. Des informations supplémentaires sont fournies dans les sections suivantes. » CB AM - 600 fréquences CB AM programmées en usine entre 25,000 et 27,995 MHz.
23 bandes de balayage - Plan de bande allemand 2 Appuyez sur BAND/STEP pour sélectionner l'une des 23 bandes de balayage (plan de bande allemand comme le réglage d'usine) : Bande Plage (MHz) Pas (kHz) Mode 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 25,00000 - 29,99500 30,00000 - 49,99500 50,00000 - 79,99500 80,00000 - 82,99500 83,00000 - 84,01000 AM FM FM FM FM 84 - 87 84,01500 - 87,29500 108 - 137 137 - 138 138 - 144 144 - 146 146 - 156 156 - 157 157 - 158 158 - 160 160 - 162 162 - 162 162 - 174 406
Pour une utilisation dans d'autres pays le Plan de bande 2 RU/ International peut être intéressant: 8 Bande Plage (MHz) Pas (kHz) Mode 25 - 30 30 - 50 50 - 80 80 - 83 83 - 84 84 - 87 108 - 137 137 - 138 138 - 144 144 - 146 146 - 156 156 - 157 157 - 158 158 - 160 160 - 162 162 - 162 162 - 174 406 - 440 440 - 450 450 - 466 466 - 470 470 - 512 806 - 960 25,00000 - 29,99500 30,00000 - 49,99500 50,00000 - 79,99500 80,00000 - 82,99500 83,00000 - 84,01000 84,01500 - 87,29500 108.00000 - 136.99166 137.
Le scanner offre les données de réception suivantes Bande de fréquence Sensibilité (Nominale) 12 dB SINAD 25,000 - 27,995 0,4 µV 28,000 - 69,9950 0,2 µV 70,0000 - 87,2950 0,2 uV 108,0000 - 136,9916 0,4 uV 137,0000 - 147,9950 0,2 uV 148,0000 - 174,0000 0,2 uV 406,0000 - 512,0000 0,3 uV 806,0000 - 960,0000 0,4uV Bande de fréquence bruit et un bourdonnement (Nominal) 25,000 - 27,995 48 dB 28,000 - 87,2950 43 dB 108,0000 - 136,9916 48 dB 137,0000 – 174,0000 43 dB 400,0000 - 512,0000
Les articles suivants sont inclus dans le paquet : • Scanner AE355M • Antenne télescopique intégrée • Adaptateur secteur • Adaptateur pour véhicule 12 V CC avec prise allume-cigare • Cordon d'alimentation 12 V CC avec « extrémités ouvertes » pour câblage réel d'alimentation à partir d’autres sources d'alimentation 12 V (tels que bateau, caravane ou une alimentation secteur) • Support de montage mobile • Vis • Guide d'utilisation • Autre documentation imprimée Si l’un de ces éléments est ma
Conseils utiles : • Si de fortes interférences ou du bruit électrique est reçu, éloignez le scanner ou son antenne de la source. • Si vous utilisez le scanner dans une zone de franges de distorsion ou si vous voulez améliorer la réception, utilisez une antenne de station pour scanner de base optionnelle de la marque Albrecht destinée à la couverture de plusieurs bandes. (Vous pouvez acheter ce type d'antenne auprès de notre boutique en ligne ou dans un magasin d'électronique local.
Installation permanente du scanner AE355M 1. Choix d’un emplacement pour l’AE355M. Evitez tous les endroits qui pourraient gêner la conduite de votre véhicule. Dans une voiture privée, l'emplacement idéal est au-dessous du tableau de bord côté passager. 2. Utilisez le support de fixation (en option) comme modèle pour marquer l'emplacement des vis de montage. Remarque : S’il y a des vis qui tiennent déjà le tableau de bord, vous pouvez utiliser les trous de ces vis pour fixer le support. 3.
Aperçu de l’utilisation du scanner Panneau avant du AE355M Touche Fonction HOLD Appuyez sur cette touche pour arrêter le balayage ou la recherche et de rester sur la fréquence en cours. « HOLD » s'affiche à l'écran. Appuyez de nouveau sur HOLD pour reprendre le balayage. UP Appuyez sur ces touches directionnelles pour : • Rechercher manuellement vers le haut ou vers le bas des fréquences en mode Hold. ou DOWN • Changer la direction d'une recherche en mode Recherche.
Touche Fonction FRN/PMR Appuyez sur cette touche pour balayer les bandes Freenet (FRN) et PMR. Appuyez sur cette touche pour parcourir les fréquences dans l'ordre suivant : • Freenet (FRN)/PMR – les deux activés • Freenet (FRN) seulement (banc PMR désactivé) • PMR seulement (banc Freenet désactivé) • Aucun activé (bancs Freenet et PMR désactivés) Remarque : Le banc Freenet (FRN) comprend 100 canaux Privés.
Touche Fonction CB AM/FM Appuyez sur cette touche pour balayer les bandes CB AM et la bande amateur (CB FM).
Elément Fonction Volume/Clock Bouton de contrôle de Volume/Horloge Tournez ce bouton vers la droite pour allumer l’AE355M. Continuez à tourner ce bouton vers la droite pour régler le volume. SQ Squelch contrôle Réglez SQ pour définir le seuil de balayage. Lorsque vous êtes en écoute de contrôle d’un seul canal en mode Scan Hold, réglez SQ pour éliminer le bruit de fond qu’on entendre en l'absence d'un signal entrant. LCD L'affichage à cristaux liquides (LCD) affiche le canal ou sa fréquence en cours.
Utilisation de votre scanner AE355M Réglages Réglage du Squelch (silencieux) Pour régler le Squelch 1. Tournez SQ à fond dans le sens antihoraire. Vous devez entendre le bruit de squelch ouvert. 2. Tournez SQ lentement dans le sens horaire jusqu'à ce que le bruit disparaisse. C'est le point de seuil à partir duquel le signal entrant est juste un peu plus fort que le bruit qui va ouvrir le squelch. 3. Réglez le volume à un niveau d'écoute confortable.
balayage du banc. Quand une fréquence active est trouvée, le balayage s'arrête sur cette fréquence. Lorsque la transmission se termine, le scanner marque une pause de 2 secondes avant une nouvelle transmission. Si aucune nouvelle transmission n’est trouvée, le balayage reprend. Appuyez sur UP pour poursuivre le balayage manuellement. Plusieurs bancs actifs sont balayés dans l'ordre. Remarque : Avant de pouvoir balayer le banc privé, vous devez programmer les fréquences dans les canaux.
En appuyant plusieurs fois sur AIR/MARINE on fait défiler les bancs dans cet ordre : 1. Air/Marine 2. Air 3. Marine 4. Aucun En appuyant plusieurs fois sur CB AM/FM on fait défiler les bancs dans cet ordre : 1. CB AM et bande amateur de 10 m (CB FM) 2. CB AM 3. Bande amateur de 10 m (CB FM) 4.
Conseils pour le balayage de bancs de service Si vous voulez faire - Voici comment - Lancer le balayage Appuyez sur une touche banc de service ; le nom de banc se met à clignoter et le message "SCAN" se déplace sur l'écran. Le balayage s'arrête automatiquement sur un canal actif et affiche cette fréquence (sauf pour les canaux verrouillés qui seront abordés plus loin dans ce guide). Il restera sur ce canal jusqu'à ce que la transmission se termine.
Si vous voulez faire - Voici comment - Continuer le balayage après qu’AE355M s'est arrêté sur un canal actif Si l’AE355M s'arrête sur un canal actif que vous ne voulez surveiller mais vous ne voulez pas le verrouiller, appuyez sur . Vous balayerez la fréquence suivante. Sélectionnez un autre banc à balayer Utilisez l'une des deux méthodes suivantes : • Utilisez la touche pour vous déplacer dans les fréquences et les bancs.
Ecrans Cette section montre quelques affichages d'écran typiques : Balayage de bancs Cet écran affiche le balayage de l’AE355M d'un banc affiché. "SCAN" défile de droite à gauche sur l'écran et le banc balayé clignote. Cet écran montre que le scanner a été mis en mode HOLD (attente) pour surveiller la fréquence 149,025 du banc Freenet. Lorsque BAND/STEP est appuyée cet écran affiche la plage de bandes à rechercher.
Fonctions spéciales Le scanner AE355M offre plusieurs fonctionnalités spéciales : • Verrouillage de canaux/fréquences • Appel rapproché • Banc privé • Fréquences programme dans des bancs programmables • Verrouillage de programme • Sélectionné du pas des fréquences • Mode horloge Verrouillage de canaux/fréquences Parfois, le scanner peut s'arrêter sur un canal ou une fréquence particulière à cause du bruit ou d'autres transmissions non désirées.
Vous ne pouvez verrouiller que les canaux ou fréquences des bancs Private, EMG, Freenet (FRN), PMR et Marine. Si vous verrouillez tous les canaux ou les fréquences dans l’un de ces bancs en appuyant sur la touche du banc, le scanner émet une tonalité d'erreur et n’effectue pas le balayage. Conseils de balayage 24 Si vous voulez faire Voici comment - Verrouiller temporairement Lorsqu’on est sur un canal ou une fréquence, appuyez une fois sur L/O.
Verrouiller temporairement (suite) • Appuyez sur le banc soumis au balayage pour reprendre le balayage dans ce banc. • Appuyez sur une autre touche banc pour lancer le balayage de ce nouveau banc. Verrouillage permanent Lorsqu’on est sur un canal ou une fréquence, appuyez rapidement deux fois sur L/O. Le scanner verrouille ce canal ou cette fréquence, affiche «T L/O », puis « L/O », puis reprend le balayage.
Restauration de 1 tous les canaux/Fréquenc es verrouillés de façon permanente 2 Vous pouvez déverrouiller tous les canaux programmables verrouillés et rechercher les fréquences ignorées dans un banc en même temps. Appuyez sur une touche banc pour lancer le balayage. Restauration de 3 tous les canaux/Fréquenc es verrouillés de 4 façon permanente (suite) Maintenez appuyée L/O pendant plus de 2,5 secondes jusqu'à ce que vous entendiez deux bips. Appuyez sur HOLD pour arrêter le balayage.
Close Call seulement jusqu'à ce que le scanner affiche une ligne composée de Maintenez appuyée tirets et l'icône clignote. Le scanner est maintenant en mode Close Call seulement. Il va essayer uniquement de trouver des transmissions Close Call. C'est aussi la première étape pour accéder aux modes de configuration Close Call. Configuration des modes Close Call pour accéder au mode Close Call seulement. 1. Maintenez appuyée la touche L'écran affiche une ligne composée de tirets. 2.
1. De l'étape 4 précédemment sélectionnez C-C band. La sélection de la première bande s’affiche : 2. Faites défiler vers le haut ou le bas pour sélectionner les bandes Close Call à surveiller. Appuyez sur PROG. L'écran affiche cette sélection et « On ». Vous ne pouvez pas désactiver toutes les bandes. Si vous désactivez toutes les bandes b1 Lo (bande basse VHF) est automatiquement réglé sur ON (activée).
Sauvegarder une 1. fréquence trouvée par Close Call Si le scanner trouve un signal de voisinage grâce à Close Call il va à cette fréquence, mais ne l'affiche pas. Cependant il affiche le numéro de bande et "Found" se met à clignoter. 2. Appuyez sur une touche pour confirmer la fréquence. 3. Suivez les étapes pour « Programmation d'un canal » dans le chapitre suivant. Banc privé AE355M fournit également trois bancs distincts pour conserver les fréquences favorites.
Programmation d'un canal Les étapes suivantes détaillent comment programmer une fréquence dans un canal d'un banc particulier lorsque la fréquence a été trouvée pendant le balayage ou la recherche. Dans cet exemple la fréquence a été trouvée pendant le balayage du banc Freenet (FRN). Cet écran montre que la fréquence SCAN 149,025 a été trouvée par une recherche du banc actif (clignotant) Freenet (FRN). Appuyez sur HOLD. HOLD s’affiche. Appuyez sur PROG. CH s’affiche et se met à clignoter.
Appuyez sur PROG. Le scanner programme de la fréquence dans le canal indiqué puis passe en mode SCAN HOLD. Appuyez sur HOLD pour libérer le mode Hold et poursuivre le balayage du reste des canaux programmés en commençant par le canal que vous venez de programmer.
Suppression d'une fréquence programmée (programmation « 000,0000 ») La méthode la plus simple pour supprimer une fréquence que vous avez programmée est de l'écraser avec une fréquence nulle (000,0000). Appuyez sur HOLD pour arrêter le balayage et appuyez sur PROG. HOLD s’affiche et CH s’affiche et clignote. Maintenez appuyée L/O pendant 2,5 secondes. La fréquence devient 000,0000 et CH continue de clignoter. Appuyez sur le banc contenant le canal que vous souhaitez effacer.
Appuyez sur PROG. L'écran affiche une fréquence nulle dans ce canal. Appuyez à nouveau sur la touche banc pour reprendre le balayage dans ce banc. Fonction de verrouillage de Programme AE355M est doté d’une fonction de verrouillage de programmes afin de prévenir l’accès fortuit ou non autorisé à des programmes. Maintenez appuyée la touche PROG pendant plus de 2,5 secondes pour basculer entre Verrouillage et désactiver le programme.
3. Utilisez ou pour sélectionner les pas parmi Auto, 5kHz, 6,25, 10kHz, 12,5kHz (Lorsque "Auto" est sélectionné, le scanner recherches à partir de 84,015 MHz à 87,295 MHz avec 20 kHz d'espacement dans la bande allemande 4 m). 4. Appuyez sur la touche BAND/STEP pour changer les pas pour la bande air, le scanner affiche le pas de la bande air. 5. ou pour sélectionner les pas de la bande air entre 8,33 et 12,5 Utilisez kHz.
Guide de dépannage PROBLEME SOLUTION Le scanner ne marche pas Essayez l’une de ces options : • Vérifiez les connexions aux deux extrémités de l'adaptateur secteur. Vérifiez si la prise d'alimentation 230 V est sous tension. Dans le cas contraire, utilisez une autre prise murale. Mauvaise réception Le balayage ne s'arrête pas • Vérifiez les connexions aux deux extrémités du cordon CC ou de l’adaptateur allume-cigare. • Vérifiez si le fusible est grillé.
PROBLEME La recherche ne démarre pas PROG ne marche pas SOLUTION • Réglez le contrôle du squelch. • Vérifiez la connexion de l'antenne. Arrêtez le balayage ou la recherche. Entretien général du produit Eteignez le scanner avant de débrancher l'alimentation. Appuyez toujours sur toute touche du clavier fermement jusqu'à ce que vous entendiez la tonalité d'entrée de cette touche.
Pour modifier le réglage Plan de bande : • Eteignez le scanner et débranchez le câble d'alimentation • Appuyez sur les touches HOLD et , maintenez-les appuyées et rebranchez le câble d'alimentation. • Relâchez les touches - le numéro de Plan de bande actuel apparaît • • • • Sélectionnez le plan de bande désiré avec ou Appuyez sur PROG pour mémoriser le plan de bande. Le scanner va afficher l'heure et peut être allumé comme d’habitude.
• Freenet (FRN) : 6 canaux préprogrammés et 100 programmables • PMR : 8 canaux PMR 446 européens préprogrammés. • AIR : 3840 canaux air préprogrammés dans le monde entier. • Marine (MRN) : 57 canaux radio Marine internationaux préprogrammés. • CB AM : 600 canaux CB programmés en AM (de 25,000 MHz à 27,995 MHz) • Bande amateur de 10 m (CB FM) : 400 canaux bande 10 m programmés en FM (à partir de 28,000 MHz à 29,995 MHz). • PRIVÉ : 100 canaux entièrement programmable par l'utilisateur.
cents par minute) ou les réseaux mobiles (45 cent ou moins par minute). En tout cas, nous vous recommandons de contacter la hotline avant de retourner un scanner. Dans de nombreux cas, de problèmes peuvent être résolus par un simple appel téléphonique. Dans des cas particuliers, notre hotline peut également vous renseigner sur le réparateur le plus proche de vous ou le plus rapide pour votre scanner, ou sur un numéro de réparation par téléphone.
Déclaration de conformité CE Hiermit wird erklärt, dass unser Produkt/ par la présente nous déclarons que notre produit Empfangsgerät für Funkdienste (Balayer) Récepteur radio de services de communication AE 355 M den folgenden europäischen Normen entspricht:/ est conforme aux normes européennes suivantes EU-Richtlinien / EU directives 73/23/EEC (LVD); 2004/108/EG (EMC) and 99/5/EEC (R&TTE), EN 301 489-1 V 1.8.1, EN 301 489-5 V1.2.1, EN 301 489-13 V.1.2.1, EN 301 489-15 V1.2.1 (EMC), EN 300 086-2 V.1.2.