Albrecht DR 56 DAB+ Autoradio-Adapter mit UKW-Sender und Bluetooth-Freisprecheinrichtung für Fahrzeuge Benutzerhandbuch Deutsch / English / Français
1 1 2 3 3.1 3.2 3.3 3.4 3.5 3.5.1 3.5.2 4 5 6 6.1 6.2 7 7.1 7.2 7.3 8 9 10 11 12 13 14 15 16 17 18 19 2 Inhalt Inhalt ..................................................................... 2 Sicherheitshinweise .............................................. 3 Einführung ............................................................ 4 Lieferumfang ......................................................... 4 Bedienelemente und Anschlüsse .......................... 5 Erstgebrauch.................................
2 S 1. 2. 3. 4. 5. 6. Sicherheitshinweise Reinigen Sie das Gerät nur mit einem trockenen Tuch. Blockieren Sie keine Lüftungsöffnungen. Benutzen Sie nur vom Hersteller mitgeliefertes Zubehör. Setzen Sie das Radio nicht Regen oder Feuchtigkeit aus. Setzen Sie das Radio nicht Wasser, Wasserdampf, Sand oder sonstigen Umwelteinflüssen aus. Setzen Sie das Radio nicht übermäßiger Hitze aus.
3 3.1 1. 2. 3. 4. 5. 6. Einführung Lieferumfang DR 56 DAB+ Autoradio-Adapter für Fahrzeuge USB-Doppelladegerät für 12-Volt-Steckdose Saugnapfhalterung 3,5 mm Audiokabel USB-Versorgungskabel DAB+ Scheibenantenne Hinweis: Alle Zubehörteile sind speziell auf das DR 56 zugeschnitten. Zubehör von Drittherstellern führt möglicherweise zu Fehlfunktionen.
3.2 Bedienelemente und Anschlüsse Bedienelemente: 1. Ein-/Ausschalter 2. 3,5 mm Eingang/Ausgang 3. Drehknopf 4. Modus 5. Micro-USB Stromeingang 6. Antenneneingang 7. TX/Scannen 8. Menü 9. Senderspeicher/Telefon/Wiedergabe/Pause 10.
3.3 Erstgebrauch 1. Montieren Sie den DR 56 DAB+ Autoradio-Adapter mit der mitgelieferten Saugnapfhalterung an der Windschutzscheibe. 2. Schließen Sie das USB-Stromkabel am Micro-USB-Stromeingang des DR 56 und am USB-Doppelladegerät an. Stecken Sie das USB-Doppelladegerät in den Zigarettenanzünder. 3. Schließen Sie die mitgelieferte Antenne am Antenneneingang an. Zum korrekten Anschluss der Antenne, siehe Kapitel 10. 4.
3.4 Kabelverbindung 1. Verbinden Sie den 3.5mm Ausgang des DR56 mit dem mitgelieferten Audiokabel mit dem Line-In Eingang Ihres Autoradios. 2. Halten Sie „Menu“ zum Aufrufen des Menüs gedrückt, dann suchen Sie mit dem Drehknopf „Aux In/Out“ und bestätigen mit Tastendruck auf „Menu“. Drücken Sie „Mode“ zum Verlassen des Menüs. Das Kopfhörersymbol „ “ wird oben im blauen Balken angezeigt. Hinweis: Im Modus „Aux-Out“ haben Sie keine UKW-Übertragung an das Autoradio. 3.
2. Drücken Sie „TX/Scan“ zur Anzeige der UKW-Übertragungsfrequenz (TX Freq). 3. Dann halten Sie „TX/Scan“ für 3 Sekunden zur Aktivierung des automatischen Scans einer „unbesetzten“ (ohne Störung durch andere Kanäle) Übertragungsfrequenz gedrückt. Der Scan dauert ca. 20-30 Sekunden und im Display wird „---.-MHZ“ angezeigt; die Suche wird bei einer unbesetzten Frequenz unterbrochen. 4.
3.5.2 Manuell UKW-Übertragungsfrequenz wählen: 1. Drücken Sie „TX/Scan“ zum Aufrufen des Auswahlmodus für die UKW-Übertragungsfrequenz. 2. Mit dem Drehknopf wählen Sie dann Ihre unbesetzte Frequenz (basierend auf Ihrer Erfahrung mit der bekannten unbesetzten Frequenz), die Sie auf Ihrem Autoradio empfangen möchten. 3.
gewünschten DAB+ Kanal, dann drücken Sie erneut „Menu“ zur Auswahl. 4. Alternativ halten Sie „TX/Scan“ für 3 Sekunden zur erneuten Aktivierung von „Auto Scan“ gedrückt, sofern die DAB+ Radiokanäle aktualisiert werden sollen. Hinweis: Im Normalgebrauch müssen Sie den „Auto Scan“ nicht jedes Mal erneut durchführen, wenn Sie das DAB+ Radio benutzen, außer wenn es neue DAB+ Kanäle gibt. Der Scan erfolgt ähnlich wie bei Ihrem Fernseher.
6 Senderspeicher verwalten: 6.1 Sender speichern Zur Speicherung Ihrer beliebtesten DAB+ Sender gehen Sie wie folgt vor: 1. Wählen Sie den gewünschten DAB+ Sender mit dem Drehknopf. 2. Halten Sie „Preset“ für 3 Sekunden zum Aufrufen des „Favorit speichern“ Modus gedrückt. 3. Mit dem Drehknopf scrollen Sie zum gewünschten Senderspeicher. 4. Drücken Sie „Preset“ zur Bestätigung und zum Verlassen des „Favorit speichern“ Modus. Die Meldung „Speichern erfolgreich“ wird angezeigt. 6.
7 Bluetooth-Geräte verwalten: 7.1 Telefon koppeln Zum erstmaligen Koppeln eines Telefons mit dem DR 56 gehen Sie wie folgt vor: 1. Drücken Sie „Mode“ zum Aufrufen des „Bluetooth“ Modus. 2. Im „Bluetooth“ Modus halten Sie „TX/Scan“ zur Aktivierung des Kopplungsmodus gedrückt. „Pairing läuft“ wird angezeigt. 3. Schalten Sie die Bluetooth-Funktion Ihres Telefons ein und suchen Sie nach Bluetooth-Geräten. Eine Liste verfügbarer Bluetooth-Geräte wird angezeigt. 4.
erzwingen Sie den Kopplungsmodus auf dem DR 56, um sich mit einem anderen Telefon zu verbinden zu können. Hinweis: Das blinkende Bluetooth-Symbol zeigt an, dass keine Bluetooth-Verbindung besteht. Besteht die Verbindung, so leuchtet das Symbol durchgängig. 7.2 Anrufe verwalten 1. Bei einem eingehenden Gespräch klingelt das DR 56. Drücken Sie „Preset“ zur Entgegennahme des Anrufs. Die Lautstärke und die Sprechzeit werden unten im Display angezeigt. Mit dem Drehknopf stellen Sie die Lautstärke ein. 2.
5. 6. Mit dem Drehknopf stellen Sie die Lautstärke nach Auswahl von „Interner Lautsprecher“ ein. Im Modus „Auto Lautsprecher“ kann die Lautstärke nur mit dem Lautstärkeregler des Autoradios eingestellt werden. „Auto Lautsprecher“ wird unten im LCD-Display angezeigt. Hinweis: 1. Der eingebaute Lautsprecher arbeitet nur für das Telefon bei Verbindung über Bluetooth für die Lautstärke. 2.
8 Musikwiedergabe vom Handy Zum Musikhören von Ihrem Handy steht Ihnen Bluetooth oder Aux-In zur Verfügung. Zur Wiedergabe über Bluetooth rufen Sie den Bluetooth-Modus im DR 56 auf und koppeln Sie Ihr Handy, wie im Abschnitt 7.1 beschrieben. Dann starten Sie die Wiedergabe über Bluetooth auf dem Handy (siehe Bedienungsanleitung Ihres Mobiltelefons für weitere Informationen). Auf dem DR 56 können Sie folgende Einstellungen vornehmen: 1.
Hinweis: 1. Nach dem Koppeln Ihres Handys mit dem DR 56 wird die Verbindung zwischen den beiden Geräten jedes Mal automatisch wieder hergestellt, wenn Sie damit in das Fahrzeug einsteigen und den DR 56 einschalten. Der DR 56 verbindet sich automatisch mit dem zuletzt verbundenen Handy.
9 Hintergrund-/ Schriftfarbe wählen Die Hintergrund-/ und Schriftfarbe können auf vier verschiedene Kombinationen zum Abgleich auf die Farben Ihres Armaturenbretts eingestellt werden: 1. 2. 3. 4. Schwarzer Hintergrund/weiße Schrift Schwarzer Hintergrund/blaue Schrift Schwarzer Hintergrund/orangefarbene Schrift Hellblauer Hintergrund/schwarze Schrift Zum Einstellen der Farbe gehen Sie wie folgt vor: Halten Sie „Menu“ für 3 Sekunden zum Aufrufen des „Menüfarbe“ Modus gedrückt.
10 Antenne anschließen und montieren Für besten Empfang installieren Sie die DAB+ Fensterantenne, wie in der Abbildung in Position B gezeigt. 1. Zur Installation der Antenne bringen Sie die schwarze Box der Antenne in der Nähe des Metallrahmens des Fahrzeugs an. Die schwarze L-förmige Kupferfolie kleben Sie auf den Metallrahmen. Das transparente L-förmige Teil der Antenne wird dann parallel zum Rand der Windschutzscheibe aufgeklebt.
11 Aux-In: Der DR 56 ist auf der rechten Seite mit einem 3,5 mm Aux-Eingang ausgestattet. Eine externe analoge Audioquelle, wie iPad/iPhone/iPod/Tablet/Android-Handy oder MP3-Player, kann über die UKW-Übertragung in Ihr Autoradio eingespeist werden. Zum Anschluss eines externen Audiogerätes gehen Sie wie folgt vor: Drücken Sie „Mode“, bis „AUX IN“ angezeigt wird. Können Sie „AUX IN“ nicht finden, so halten Sie „Menu“ zum Aufrufen des Menüs gedrückt. 1.
12 USB-Geräte laden 1. Schließen Sie das USB-Kabel Ihres Mobiltelefons am USB-Port des USB-Doppelladegeräts mit 12-Volt-Stecker an. 2. Schließen Sie das andere Ende des Kabels zum Laden an Ihrem Gerät an. (Spannungsausgang: 5V, 1A, die Stromstärke reicht zum Laden eines iPad aus) 13 LC-Display dimmen: Bei Nachtfahrten können Sie die Helligkeit des LCD-Displays durch langes Drücken von „Mode“ dimmen. Halten Sie „Mode“ zur Rückkehr zur Normalhelligkeit gedrückt. 14 Sprache wählen: 1.
15 Rückstellung zu den Werkseinstellungen: 1. Halten Sie „Menu“ zum Aufrufen des Menüs gedrückt. 2. Mit dem Drehknopf scrollen Sie zur Auswahl von „Werkseinstellung” und bestätigen mit erneutem Tastendruck auf „Menu“. 3. Mit dem Drehknopf wählen Sie „Ja“ oder „Nein“ zur Rückstellung, dann bestätigen Sie mit „Menu“. 16 Software-Version des Geräts anzeigen: 1. Halten Sie „Menu“ zum Aufrufen des Menüs gedrückt. 2.
17 Technische Daten: Modell: DR 56 Unterstütztes Radioformat: DAB+ und UKW-Sender DAB+ Frequenz: Band III (174,00 –239,00 MHz) UKW-Übertragungsfrequenz: 87,5—108 MHz Bluetooth: Version 2.1 Ausgangsleistung Lautsprecher: 1,0 W, 8 Ausgangsleistung Audio: 3,5 mm Stereo-Klinke Spannungsausgang: 5 V, 1 A (laden von iPad2/iPhone/iPod/Android-Handy usw.) Spannungsversorgung: Zigarettenanzünder (10V 30V) Abmessungen: 96 x 75 x 248 mm Nettogewicht: Ca.
18 Gewährleistungs- und Recyclinginformationen Wir sind verpflichtet, jedem Gerät Informationen über die Entsorgung, über die gesetzlichen Gewährleistungsbestimmungen und die EG Konformitätserklärungen mit Hinweisen über das Benutzen der Geräte in den verschiedenen Ländern beizufügen. Sie finden daher diese Informationen im folgenden Text.
Elektroschrottgesetz und Recycling Europäische Gesetze verbieten das Entsorgen von defekten oder nicht mehr brauchbaren Geräten über den Hausmüll. Sollten Sie eines Tages Ihr Gerät entsorgen wollen, dann geben Sie es bitte nur bei den überall eingerichteten kommunalen Sammelstellen zum Recycling ab. Dieses Sammelsystem wird von der Industrie finanziert und sichert auch die umweltgerechte Entsorgung und das Recycling wertvoller Rohstoffe.
Albrecht DR 56 In-Car DAB+ Radio adapter with FM Transmitter & Bluetooth Hands-free User Manual English
1 1 2 3 3.1 3.2 3.3 3.4 3.5 4 5 6 6.1 6.2 7 7.1 7.2 7.3 8 9 10 11 12 13 14 15 16 17 18 19 20 Content Content ............................................................... 26 Safety Instructions............................................... 27 Introduction ......................................................... 28 Scope of Delivery ................................................ 28 Buttons and Connections .................................... 29 First Use ...............................................
2 Sa 1. 2. 3. 4. 5. 6. Safety Instructions Clean with dry cloth. Do not block any ventilation openings. Only use accessories provided by the manufacturer. Do not dispose this radio to rain or moisture. Do not allow this unit to be exposed to water, steam, sand or other environmental hazards. Do not leave your radio where excessive heat could cause damage.
3 3.1 Introduction Scope of Delivery DR 56 In-Car DAB+ Radio adapter Dual USB car charger for 12V socket Suction cup mount 3.5mm audio cable USB Power supply cable DAB+ window mount antenna Remark: All accessories are especially made to work with the DR 56. Other third party accessories might not be function properly.
3.2 Buttons and Connections Controls: 1. Power On/Off Switch 2. 3.5mm Line-In or Line-Out Socket 3. Tuning Knob 4. Mode Button 5. Power Supply Cable Socket 6. Antenna Socket 7. TX/Scan Button 8. Menu Button 9. Preset/Phone/Play/Pause Button 10.
3.3 First Use 1. Mount the DR 56 In-Car DAB+ Radio adapter to the windscreen using the provided suction cup mount. 2. Connect one end of the USB power supply cable to the Micro USB socket in the DR 56 and the other end to the dual USB car charger. Plug the dual USB car charger to the car cigar-lighter socket. 3. Connect the supplied antenna to the antenna socket. To mount the antenna correctly please refer to chapter 10. 4.
3.4 Connection via Line-Out 1. Connect the 3.5mm line-out socket of the DR56 through the supplied audio cable with the line-in socket of your car rado. 2. Press and hold the “Menu” button to enter menu mode, use the Tuning Knob to search for “Aux In/Out” and confirm by shortly pressing “Menu” again. Use the Tuning Knob to select “Aux-Out” and confirm by shortly pressing the “Menu” button again. Shortly press the “Mode” button to exit the menu.
2. Press “TX/Scan” button to show the FM transmitting frequency (TX Freq). 3. Then press and hold the “TX/Scan” button for 3 seconds to activate the automatic scanning of a “vacant” transmission frequency without interference with other channels. The scanning process will take 20-30 seconds the display will show “---.-MHZ” and stop at a vacant frequency. 4.
3.5.2 Select FM Transmitting Frequency (Manual): 1. Press the “TX/Scan” button to enter the FM transmitting frequency selection mode. 2. Then use Tuning Knob to select your desired vacant frequency (based on your past experience with the known vacant frequency) which you would like to receive by your car radio. 3.
4 Search and select DAB+ channels: 1. Press the “Mode” button until “DAB+ Radio” mode is found 2. Use the Tuning Knob to select the desired DAB+ channel 3. Or press “Menu” button to enter the station list, use the Tuning Knob to scroll up or down to select the desired DAB+ channel and press the “Menu” button again to select. 4. You may also press and hold the “TX/Scan” button for 3 seconds to re-activate the “Auto Scan” process if you need to update the DAB+ radio channels.
5 Service Information: DAB+ Mode The Service Information data will be displayed with scrolling text which is being broadcasted from the station. While listening to DAB+, the display will show the following information if applicable 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11.
6 Manage the Preset Stations: 6.1 Storing the Preset Stations To program and store your favorite DAB+ preset stations, 1. Select your desired DAB+ station using the Tuning Knob. 2. Press and hold the “Preset” button for 3 seconds to enter “Store Preset Stations” mode 3. Use the Tuning Knob to scroll up or down to select a number in the memory to store the selected station, 4. Press the “Preset” button to confirm and exit “Store Preset Stations” mode.
7 Manage the Bluetooth Devices: 7.1 Pairing a Phone To pair a phone with the DR 56 for the first time, follow the below procedures: 1. Press the “Mode” button until you have entered the “Bluetooth” mode. 2. In “Bluetooth” mode, press and hold the “TX/Scan” button to activate the pairing mode, the message “Pairing in progress” will be shown. 3. On your phone, turn on Bluetooth and search for Bluetooth peripherals, a list of available Bluetooth peripherals will be displayed, 4.
Remark: The flashing of the Bluetooth icon indicates the Bluetooth is not connected and once it is connected, the icon will stop flashing. 7.2 1. Managing Phone Call When there is an incoming call, the DR 56 rings with a ringtone. Press the “Preset” button to answer a call and at the same time the speaker phone volume and talk time will be displayed at the bottom of the screen. You may use Tuning Knob to adjust the volume level. 2. Press and hold the “Preset” button to decline a call 3.
Remark: 1. The Built-in speaker only works for phone voice when it is connected via Bluetooth. 2. When the “Car Speaker” is selected, the phone voice can be fed into the car stereo system by either using Line-Out or FM transmitter. 3. Please note that when using the “Car Speaker” other persons might be able to listen to your phone calls when they are in the car next to you, e.g. in a traffic jam, and their car stereo system is accidentally on the same frequency as the DR 56. 4.
To play it via Aux-In please do the following: 1. Make sure you have selected “Aux-In” mode by pressing and hold “Menu” button to enter menu mode, use Tuning Knob to search for “Aux-In/Out Select” and confirm by short press “Menu” again. Use Tuning Knob to select “Aux-In” and confirm by short press “Menu” button. 2. Press “TX/Scan” button to enter FM transmitting frequency selection mode, 3. Then use Tuning Knob to select your favorite vacant frequency Remark: 1.
3. If you want to connect DR 56 to another phone while the first phone is still in connection, you may force the first phone to disconnect by press and hold “TX/Scan” button to enter pairing mode again and a flashing Bluetooth icon will appear at the top of the display. Then you may pair to a new phone. This operation only works when the new phone has not been paired with DR 56 before.
10 Connecting and Mounting the Antenna To get the best reception please mount the DAB+ window mount antenna as shown in Position B in the diagram below. To mount the antenna please put the black box of the antenna in position next to the metal frame of the car. The black L-shaped copper foil should be glued onto the metal frame. The transparent L-shaped part of the antenna is then glued parallel to the edge of the windscreen.
11 Aux-In: The DR 56 features a 3.5mm Aux-In jack on the right-hand side. External analog audio source from iPad/iPhone/iPod/Tablet/Android phone or MP3 players etc. can be fed through FM transmission into your car stereo audio system. To connect an external music player: Press the “Mode” button until you see “AUX IN” mode. If you can’t find “AUX IN” mode, then press and hold “Menu” button to enter the menu 1.
12 Charging USB devices 1. Use your mobile phone USB cable and plug the USB connector into the dual USB car charger with 12V socket 2. Connect the other end of the cable to your device and start charging. (Charging Power Output: 5V, 1A, the current is big enough for iPad charging) 13 LCD Display Dimmer Control: When driving at night, you may control the brightness of the color LCD display by pressing and holding the “Mode” button to dim the display.
15 Restore factory setting: 1. Press and hold the “Menu” button to enter the menu 2. Use the Tuning Knob to scroll up or down to select “Factory Reset” and confirm by pressing the “Menu” button again 3. Use the Tuning Knob to select “YES” or “NO” for the reset and confirm it by pressing the “Menu” button. 16 Checking the Software Version of the device: 1. Press and hold the “Menu” button to enter the menu 2.
17 Product Specification: Product Model: DR 56 Radio format support: DAB+ and FM transmitter DAB+ frequency: Band III (174.00 –239.00MHz) FM transmission frequency: 87.5—108MHz Bluetooth: Version 2.1 Speaker phone output: 1.0W, 8 Audio Line-Out : 3.5mm stereo jack Power output : 5V, 1A (charging for iPad2/iPhone/iPod/Android Phone etc. ) Power Source: Car Cigar-lighter Socket (10V- 30V) Dimension: 96x 75 x 248 mm Net weight: 128g ( approx.
18 Warranty and Recycling Information We are legally obliged to include disposal and warranty information as well as EU declaration of conformity with the use instructions in different countries for every unit. Please find this information on the following pages. 2-Year Warranty From Date Of Purchase The manufacturer/retailer guarantees this product for two years from date of purchase.
19 WEEE and Recycling The European laws do not allow any more the disposal of old or defective electric or electronic devices with the household waste. Return your product to a municipal collection point for recycling to dispose of it. This system is financed by the industry and ensures environmentally responsible disposal and the recycling of valuable raw materials.
Albrecht DR 56 Adaptateur pour autoradio DAB+ avec fonction émetteur FM et mode mains-libres via Bluetooth Guide d'utilisateur Français
1 1 2 3 3.1 3.2 3.3 3.3.1 3.3.2 4 5 6 6.1 6.2 7 7.1 7.2 7.3 8 9 10 11 12 13 14 15 16 17 18 50 Sommaire Sommaire .......................................................................... 50 Instructions de sécurité ..................................................... 51 Introduction........................................................................ 52 Contenu de la boîte ........................................................... 52 Touches et branchements ...........................................
2 S 1. 2. 3. 4. 5. 6. 7. 8. Instructions de sécurité N'utilisez pas cet appareil près d’une source d'eau. Essuyez votre appareil avec un chiffon sec. N'obstruez pas les ouvertures d'aération. N'utilisez pas cet appareil à proximité d'une source de chaleur. Utilisez les accessoires fournis par le fabricant. N'exposez pas cet appareil à la pluie ou à l'humidité. N'exposez pas votre appareil à l'eau, à la vapeur, au sable et à tout autre risque dû à l'environnement.
3 3.1 1. 2. 3. 4. 5. 6. Introduction Contenu de la boîte Adaptateur d'autoradio numérique DR 56 Chargeur USB pour deux appareils, connectable sur une source 12 V Support de fixation à ventouse Câble audio 3,5 mm Câble d'alimentation électrique USB Antenne numérique Remarque : Tous les accessoires ont été spécialement conçus pour votre DR 56. Les accessoires d'autres fabricants risquent de ne pas fonctionner correctement.
3.2 Touches et branchements Éléments de commande : 1. Commutateur de marche/arrêt 2. Connecteur entrée/sortie auxiliaire 3,5 mm 3. Bouton de recherche de station 4. Touche Mode 5. Connecteur de l'alimentation électrique 6. Prise de l'antenne 7. Touche TX/Scan 8. Touche Menu 9. Touche Preset/Téléphone/Lire/Pause 10.
3.3 Utilisation pour la première fois 1. Fixez l'adaptateur pour autoradio numérique DR 56 sur le tableau de bord de votre véhicule à l'aide du support à ventouse. 2. Branchez l'extrémité approprié du câble d'alimentation électrique USB sur le connecteur Micro USB de votre DR 56 et branchez l'autre extrémité sur le chargeur USB. Branchez le chargeur USB sur l'allume-cigarette de votre véhicule. 3. Fixez l'antenne sur sa prise. Cette opération est décrite en détail au chapitre 10. 4.
3.3.1 1. 2. Utilisation de la sortie auxiliaire Appuyez sur la touche « Menu » et maintenez-la enfoncée jusqu'à passer en mode menu. Tournez le bouton de recherche jusqu'à sélectionner l'option « Aux In/Out » et appuyez brièvement sur la touche « Menu » pour confirmer votre choix. Tournez le bouton de recherche jusqu'à sélectionner l'option « Aux-Out » et appuyez brièvement sur la touche « Menu » pour confirmer votre choix. Appuyez brièvement sur la touche « Mode » pour quitter le menu.
de recherche jusqu'à sélectionner l'option « Aux-In » et appuyez brièvement sur la touche « Menu » pour confirmer votre choix. 2. Appuyez sur la touche « TX/Scan » pour afficher la fréquence de transmission FM (Fréq TX). 3. Appuyez sur la touche « TX/Scan » et maintenez-la enfoncée pendant 3 secondes pour activer le balayage automatique des fréquences afin de trouver une fréquence de transmission « libre », n'interférant pas avec d'autres canaux.
2. Tournez le bouton de recherche sur la fréquence que vous savez être libre (d'après votre expérience des fréquences connues pour être libres) et que vous voulez utiliser. 3. Appuyez ensuite sur la touche « TX/Scan » pour confirmer et quitter ou attendez 3 secondes le retour automatique en mode numérique. La fréquence que vous avez choisie est affichée au-dessus de la barre bleue, par exemple TX108,0MHz.
Remarque : vous n'avez pas à démarrer de recherche automatique à chaque fois que vous allumez votre radio numérique, mais uniquement pour détecter de nouvelles stations. L'opération de balayage des fréquences est similaire à celle qui est effectuée par votre téléviseur numérique. 5 Informations sur les services : Mode radio numérique Les informations de service sont affichées en même temps que le radiotexte qui est diffusé par la station.
1. Tournez le bouton de recherche jusqu'à atteindre une première station. 2. Appuyez sur la touche « Preset » et maintenez-la enfoncée pendant 3 secondes pour activer le mode présélection (« Store Preset Stations »). 3. Tournez le bouton de recherche jusqu'à atteindre la position mémoire de présélection de la station. 4. Appuyez sur la touche « Preset » pour confirmer votre choix et quitter le mode présélection (« Store Preset Stations »). Le message « Stored Successfully » apparaît sur l'écran. 6.
7 Gestion des appareils Bluetooth : 7.1 Couplage avec un téléphone Pour coupler un téléphone à votre DR 56 pour la première fois, procédez comme suit : 1. Appuyez sur la touche « Mode » jusqu'à sélectionner le mode « Bluetooth ». 2. Depuis le mode « Bluetooth », appuyez sur la touche « TX/Scan » et maintenez-la enfoncée jusqu'à afficher le message « Pairing in progress ». Le mode couplage est alors actif. 3.
bleue et le message « Not Connected » est affiché sur l'écran LCD. 6. Pour désactiver le couplage avec un téléphone, appuyez sur la touche « TX/Scan » et maintenez-la enfoncée jusqu'à ce que le DR 56 se place en mode couplage. Vous pouvez maintenant établir le couplage avec un autre téléphone. Remarque : l'icône Bluetooth clignote tout le temps qu'aucun couplage n'est établi et reste constamment allumée lorsqu'un couplage est établi. 7.2 Gestion des appels téléphoniques 1.
2. 3. 4. 5. 6. Sélectionnez l'entrée « Phone Speaker Setting » (Configuration de la sortie son pour le téléphone) à l'aide du bouton de recherche et appuyez sur la touche « Menu » pour confirmer votre choix. Indiquez si vous voulez utiliser le haut-parleur intégré (« Built-in Speaker ») ou les haut-parleurs de votre véhicule (« Car Speaker ») à l'aide du bouton de recherche et appuyez sur la touche « Menu » pour confirmer votre choix. Appuyez sur la touche « Mode » pour quitter le menu.
4. 8 Après la sélection d'un autre haut-parleur pour la sortie audio, vous devez éteindre puis rallumer votre appareil ou attendre 25-30 secondes que l'interface Bluetooth ajuste ses paramètres acoustiques pour éviter un retour audio. Lecture d'un contenu audio stocké sur le téléphone Vous pouvez écouter les contenus audio stockés sur votre téléphone via le mode Bluetooth ou entrée auxiliaire.
2. Appuyez sur la touche « TX/Scan » pour passer en mode sélection de la fréquence de transmission FM. 3. Sélectionnez une fréquence libre à l'aide du bouton de recherche. Remarque : 1. Après que vous avez couplé une première fois votre téléphone au DR 56, la connexion est ensuite établie automatiquement entre les deux appareils à chaque mise sous tension de votre DR 56. Le DR 56 se connecte automatiquement au dernier téléphone auquel il était couplé.
9 Sélection de la couleur du fond d'écran et du texte : Pour adapter la couleur du fond de l'écran et celle du texte qui est affiché à la couleur du tableau de bord de votre voiture, vous disposez des quatre combinaisons suivantes : 1. 2. 3. 4.
10 Branchement et montage de l'antenne Pour optimiser la réception, montez l'antenne numérique comme illustré dans le diagramme ci-dessous (position B). 1. Pour cela, placez la boîte noire de l'antenne juste à côté du châssis métallique de la voiture. Collez la feuille de cuivre noire en forme de L sur le châssis métallique. Collez la partie transparente en forme de L en position parallèle au bord du pare-brise.
11 Entrée auxiliaire : Votre DR 56 est équipé d'une entrée auxiliaire de 3,5 mm, située sur son côté droit. Tout contenu audio analogique provenant d'une source externe (iPad/iPhone/iPod/tablette/téléphone Android, lecteur MP3, etc.) peut être diffusé sur les haut-parleurs de votre véhicule par transmission FM. Pour écouter le contenu audio d'un lecteur externe : Appuyez sur la touche « Mode » jusqu'à sélectionner le mode « AUX IN ».
12 Chargement d'un appareil USB 1. Pour charger un appareil USB, branchez son câble USB sur le chargeur et branchez le chargeur sur un connecteur 12 V de votre véhicule. 2. Branchez l'autre extrémité du câble USB sur votre apareil. Le chargement commence immédiatement.
15 Rétablissement des réglages effectués en usine : 1. Appuyez sur la touche « Menu » pour afficher la liste des options associées. 2. Tournez le bouton de recherche jusqu'à sélectionner « Factory Reset » et appuyez sur la touche « Menu » pour confirmer votre choix. 3. Sélectionnez « YES » ou « NO » à l'aide bouton de recherche et appuyez sur la touche « Menu » pour confirmer votre choix. 16 Vérification de la version du microprogramme : 1.
17 Spécifications techniques : Modèle : DR 56 Modes radio : numérique DAB+ et FM Fréquences numériques : Bande III (174,00 –239,00 MHz) Fréquences FM : 87,5—108MHz Bluetooth : Version 2.1 Sortie haut-parleur : 1,0 W, 8 Sortie audio : Connecteur stéréo 3,5 mm Puissance en sortie : 5 V, 1 A (chargement pour iPad2/iPhone/iPod/Téléphone Android, etc.) Alimentation électrique : Allume-cigarette de voiture (10 V - 30 V) Dimensions : 96 x 75 x 248 mm Poids net : 128 g (approx.
18 Information importante Nous sommes légalement tenus d'inclure les dispositions et les informations de garantie et la déclaration de conformité de l'UE avec le mode d'emploi de chaque unité, et ce dans la langue de chaque pays. Veuillez trouvez ces informations dans les pages suivantes. Deux ans de garantie à compter de la date d’achat Le Fabricant/revendeur garantit ce produit pour deux ans à compter de la date d’achat.
Déchets d'Equipements Electriques et Electroniques (DEEE) et recyclage La loi Européennes ne permet pas la mise au rebus des équipements électriques et électroniques usagés avec les ordures ménagères. Ramenez votre produit à un centre de collecte municipal pour être recyclé. Ce système de collecte est financé par les industriels pour garantir l’élimination respectueuse de l’environnement et le recyclage de matières premières précieuses.