40391 36” x 24” POLYMER CABINET ASSEMBLY INSTRUCTIONS DIVISION OF S&H INDUSTRIES 5200 Richmond Road Cleveland, OH 44146 Phone 216-831-0550 Toll Free 800-253-9726 Fax 216-831-9573 www.shindustries.com E-mail: www.service@shindustries.com Rev.
40391 Assembly Instructions Page 2 WARNING! Do not use an ALC Cabinet Blaster until you have read this manual and you understand its contents and warnings. These warnings are included for the health and safety of the operator and those in the immediate vicinity. Keep this manual for future reference. Dust created by power sanding, sawing, grinding, drilling, and other construction activities may contain chemicals known to cause cancer, birth defects or other reproductive harm and respiratory illnesses.
40391 Assembly Instructions Page 3 36” X 24” POLYMER CABINET – 40391 Key Part No. Description Qty. 1 11646 Louver vent 1 2 11659 Hinge 1 3 11160 8-32 x 1/2” Screw 5 4 11161 8-32 Nut 14 5 10904 Plug 2 6 11644 Snap fastener 5 7 11647 Lens 1 8 11652 Leg (LF & RR) 2 9 11652 Leg (RF & LR) 2 10 11658 Rear support 1 ADDITIONAL PARTS NOT SHOWN ON SCHEMATIC 11580 Grate 1 40343 Pick-up tube 1 Key 11 12 13 14 15 16 17 18 19 20 Part No.
0391 Assembly Instructions Page 4 36” x 24” POLYMER CABINET SIPHON GUN REPLACEMENTS PARTS Part No. 11604 40050 40051 40052 Description Sandblast gun (economy) 13/64” Steel nozzle, 7 CFM 1/4” Steel nozzle, 15 CFM 5/16” Steel nozzle, 20 CFM 40047 5/64” Air jet, 7 CFM 40048 1/8” Air jet, 15 CFM 40049 5/32” Air jet, 20 CFM Nozzles and air jets are the only replacement parts available for economy sandblast gun. Part No.
40391 Assembly Instructions Page 5 36” x 24” POLYMER CABINET DRAWING SHOWING LEG LOCATION Left front leg and right rear leg are not the same as right front leg and left rear leg. Leg top with two holes on one side should point front and rear, not to side of cabinet. Install legs per instructions. After installation of all corner legs, install side supports and back support.
40391 Assembly Instructions Page 6 ASSEMBLY INSTRUCTIONS 1. Install all four legs: there are two types of legs. One leg fits Left Front (LF) or Right Rear (RR). The other leg fits Right Front (RF) or Left Rear (LR). 2. Take gloves and slip over circular flanges inside the cabinet. Secure gloves to flanges with glove clamps. If cabinet is supplied with 18” rubber gloves, help may be required to stretch gloves over the flanges. This is normal.
40391 Assembly Instructions Page 7 AIR COMPRESSOR RECOMMENDATION: To permit efficient operation of your air compressor, follow these guidelines: 1. Use a smaller size nozzle and air jet to control the demand of air. 2. Do not blast continuously. Stop blasting operation periodically to allow the compressor to cool. No compressor is designed to constantly run at full RPM. Use 70% of the rated output. 3. Use a minimum 1/2” air hose or metal piping from your air compressor to the blaster.
40391 Assembly Instructions Page 8 CABINET BLASTER SAFETY PROCEDURES CAUTION: READ THESE SAFETY PROCEDURES IN THEIR ENTIRETY – PARTS OF THE OPERATING INSTRUCTIONS ARE WITHIN THESE WARNINGS. These procedures are not intended to be exhaustive due to the many variables in the abrasive blasting field. Therefore, we INSIST that the hands, ears, mouth, nose and eyes be covered with appropriate safety protection at all times. ADDITIONAL WARNINGS! CAUTION MUST BE EXERCISED BY USER AT ALL TIMES 1.
40391 Assembly Instructions Page 9 WARNING! The threads on the nozzle holder and set screws must be inspected each time the nozzle is secured to the holder. Check the threads for wear, and make sure nozzle set screw securely grips the nozzle. The nozzle washer must also be inspected for wear. Worn nozzle washers cause erosion. A loose-fitting nozzle may eject from the holder under pressure and could cause severe injury. MOUNTING INSTRUCTIONS FOR THE ECONOMY LIGHT KIT 1. 2. 3. 4. 5. 6. 7. 8.
40391 Assembly Instructions Page 10 WARNING Follow all electrical and safety codes as well as the National Electrical Code (NEC) and OSHA Regulations. Part No.
40391 Assembly Instructions Page 11
40391 Assembly Instructions Page 12 Maximum 60 watt light bulb (not included)
40391 Assembly Instructions Page 13 MAINTENANCE WARNING! Failure to observe the following before performing any maintenance could cause serious injury or death from the sudden release of compressed air: Disconnect power supply. Lockout and tagout the compressed air supply. Bleed the air supply line to the blast gun. Immediate replacement of worn components is required.
40391 Assembly Instructions Page 14 PROBLEM/CAUSE POSSIBLE SOLUTION Surging of blast flow: Air pressure too low Check pressure gauge on air compressor Excessive media consumption: Air pressure too low Check pressure gauge on air compressor Clogging and plugging of blast flow: Debris in media Media size too large Nozzle plugs Wet media Purge and screen Use smaller grit size Use larger nozzle and correct Dry media, drain water from air Moisture in abrasive media: Wet media Water in air Change or use
40391 Assembly Instructions Page 15 Coal Slag # 40093 Coal Slag is used when paint and rust has to be removed from steel, such as car bodies, tanks or heavy machinery. Coal Slag is faster cutting, can be re-used, is moisture free, and will not pack or absorb moisture. (25 Lb. container) Steel Grit #40109 Steel grit is extremely fast cutting on rusty metal and hard to remove paint. Steel Grit is popular because it leaves a very smooth finish.
40391 Assembly Instructions Page 16 Disclaimer of Warranties. S & H Industries, Inc. ("Seller") makes no warranties with respect to any goods delivered to Buyer or users except as specifically set forth within this manual. S & H INDUSTRIES, INC. MAKES NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE WITH RESPECT TO ANY OF THE GOODS, AND S & H INDUSTRIES, INC. EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES AGAINST INFRINGEMENT. S & H INDUSTRIES, INC.
