User's Manual
Table Of Contents
- G-240W-A Product Guide
- Preface
- ETSI ONT safety guidelines
- ETSI environmental and CRoHS guidelines
- ANSI ONT safety guidelines
- Contents
- List of figures
- List of tables
- 1 — G-240W-A unit data sheet
- 1.1 G-240W-A part numbers and identification
- 1.2 G-240W-A general description
- 1.3 G-240W-A software and installation feature support
- 1.4 G-240W-A interfaces and interface capacity
- 1.5 G-240W-A LEDs
- 1.6 G-240W-A detailed specifications
- 1.7 G-240W-A GEM ports and T-CONTs
- 1.8 G-240W-A performance monitoring statistics
- 1.9 G-240W-A functional blocks
- 1.10 G-240W-A standards compliance
- 1.11 G-240W-A special considerations
- 2 — Install a G-240W-A indoor ONT
- 3 — Replace a G-240W-A indoor ONT
- 4 — Configure a G-240W-A indoor ONT
- 4.1 General
- 4.2 HGU mode GUI configuration
- Login
- Procedure 4-1 Login to web-based GUI
- Device and connection status
- Procedure 4-2 Device information retrieval
- Procedure 4-3 LAN status retrieval
- Procedure 4-4 WAN status retrieval
- Procedure 4-5 WAN status IPv6 retrieval
- Procedure 4-6 Home networking information retrieval
- Procedure 4-7 Optics module status retrieval
- Procedure 4-8 Voice information retrieval
- Network configuration
- Procedure 4-9 LAN networking configuration
- Procedure 4-10 LAN IPv6 networking configuration
- Procedure 4-11 WAN networking configuration
- Procedure 4-12 WiFi networking configuration
- Procedure 4-13 Routing configuration
- Procedure 4-14 DNS configuration
- Procedure 4-15 TR-069 configuration
- Security configuration
- Procedure 4-16 Firewall configuration
- Procedure 4-17 MAC filter configuration
- Procedure 4-18 IP filter configuration
- Procedure 4-19 URL filter configuration
- Procedure 4-20 DMZ and ALG configuration
- Application configuration
- Procedure 4-21 Port forwarding configuration
- Procedure 4-22 DDNS configuration
- Procedure 4-23 NTP configuration
- Procedure 4-24 USB storage configuration
- Procedure 4-25 UPnP and DLNA configuration
- Maintenance
- Procedure 4-26 Password configuration
- Procedure 4-27 LOID configuration
- Procedure 4-28 SLID configuration
- Procedure 4-29 Device management
- Procedure 4-30 Backup and restore
- Procedure 4-31 Upgrade firmware
- Procedure 4-32 Reboot ONT
- Procedure 4-33 Restore factory defaults
- Procedure 4-34 Diagnose connections
- Procedure 4-35 View log files
- RG troubleshooting counters
- Procedure 4-36 Retrieve Residential Gateway (RG) troubleshooting counters
- 4.3 SFU mode GUI configuration
- 4.4 Operator ID
- 5 — ONT configuration file over OMCI
2 — Install a G-240W-A indoor ONT
Alcatel-Lucent 7368 ISAM ONT 2-5
Edition 02
G-240W-A Product Guide
Do not drive the screw into the wall completely. Leave approximately 1/8 in.
(6 mm) between the screw head and the wall surface.
iv Slide the wall mount keyholes on the ONT enclosure or fiber storage tray
down over the mounting screws until the ONT is securely seated.
3 Review the connection locations as shown in Figures 2-2 and 2-3.
Figure 2-2 G-240W-A indoor ONT connections (back view)
Figure 2-3 G-240W-A indoor ONT connections (side view)
4 Connect the Ethernet cables to the RJ-45 ports; see Figure 2-2 for the location of
the RJ-45 ports.
5 Route the POTS cables directly to the RJ-11 ports as per local practices.
LAN4
PON
LAN3 LAN2 LAN1 WPS WLAN RESET USB POWER ON/OFF
TEL2 TEL1
Ethernet ports (4)
(RJ-45)
POTS
ports (2)
(RJ-11)
USB
port
Reset
button
Wireless
On/Off
button
Wi-Fi
security
button
Fiber
Optic
port
24434
On/Off
button
Power
input
24435
LED
USB
LED
indicator
USB
port
R05.02.01 | October 2015 | 3FE-45360-AAAA-TCZZA | Edition 02