8008- User Guide
Table Of Contents
- 1 Getting to know your telephone
- 2 Contacts management
- 3 Speed dial management
- 4 Using your telephone
- 4.1 Information about the phone
- 4.2 Manage the call log
- 4.3 Calling by number
- 4.4 Calling by name
- 4.5 Call from call log
- 4.6 Make a call using your list of contacts
- 4.7 Calling using speed dial key
- 4.8 Receiving a call
- 4.9 Switching between audio modes
- 4.10 Activating the loudspeaker during a conversation (handset lifted)
- 4.11 Redialing
- 4.12 Sending DTMF signals
- 4.13 Mute, so that your contact cannot hear you
- 4.14 Lock / unlock your telephone
- 4.15 Making a second call during a conversation
- 4.16 Answering a second call during a conversation
- 4.17 To cancel your second call and recover the first
- 4.18 Placing a call on hold (hold)
- 4.19 Switching between calls (Broker call)
- 4.20 Transferring a call
- 4.21 Three-way conference with internal and/or external contacts (conference)
- 4.22 Hide your phone number
- 4.23 Do not disturb
- 4.24 Forwarding to a number or voicemail
- 4.25 Cancelling all forwards
- 4.26 Listen to your voicemail
- 4.27 Defining a 'hotline' number
- 5 Do more with your deskphone
- 6 Programming your telephone
- 6.1 Adjusting the audio functions
- 6.2 Adjust ringer volume while a call arrives
- 6.3 Configuring the welcome page
- 6.4 Selecting language
- 6.5 Adjusting the contrast of the display
- 6.6 Programming direct call keys (8028s Premium DeskPhone, 8018 DeskPhone, add-on module)
- 6.7 Install a jack accessory (headset, hands-free, loudspeaker) (8028s)
- 6.8 Install a USB accessory (Headset, Handsfree, Loudspeaker)
- 6.9 Install a RJ9 headset (8008G, 8008)
- 6.10 Manage connected devices (8028s)
- 7 Contacting your administrator (technical support)
- 8 Accessories
- 9 Technical specifications
- 10 Ordering information
- 11 Guarantee and clauses
SIP Business
8AL90341ENACed01
45 /60
USB external ringing interface module (USB Interface module 2 relays
3GV28184AA)
8028s
8018
8008/8008G
The accessory is supported by the following sets
The USB external ringing interface module allows driving an external system (like a ring or a lamp),
following the ring tone cadence or the communication state of the phone connected on the telephone
line. No system configuration is requested to install the module.
USB Interface module 2 relays lets to connect directly one or 2 external ringings on the USB connector
of your deskphone:
Relay 2
The phone is in audio communication.
The relay is active as long as the
phone is in communication.
Relay 1
The phone is ringing. The relay
follows exactly the ring signal.
List of supplies
• USB external ringing interface module.
• 1 USB cable 1,5 m (4,9 feet) USB type A - USB type B.
Installation
WARNING: The module must be closed before use. No settings require the module to be open.
In idle state:
Ringing or during
communication:
N: common.
NC: active signal.
NO: non-active signal.
Typical usage diagram:
Phase
Neutral
The lamp lights up when the phone is in communication.
The breaking capacity is 12V/24V DC 15A or 120V/220V AC at 10A.