8008- User Guide
Table Of Contents
- 1 Getting to know your telephone
- 2 Contacts management
- 3 Speed dial management
- 4 Using your telephone
- 4.1 Information about the phone
- 4.2 Manage the call log
- 4.3 Calling by number
- 4.4 Calling by name
- 4.5 Call from call log
- 4.6 Make a call using your list of contacts
- 4.7 Calling using speed dial key
- 4.8 Receiving a call
- 4.9 Switching between audio modes
- 4.10 Activating the loudspeaker during a conversation (handset lifted)
- 4.11 Redialing
- 4.12 Sending DTMF signals
- 4.13 Mute, so that your contact cannot hear you
- 4.14 Lock / unlock your telephone
- 4.15 Making a second call during a conversation
- 4.16 Answering a second call during a conversation
- 4.17 To cancel your second call and recover the first
- 4.18 Placing a call on hold (hold)
- 4.19 Switching between calls (Broker call)
- 4.20 Transferring a call
- 4.21 Three-way conference with internal and/or external contacts (conference)
- 4.22 Hide your phone number
- 4.23 Do not disturb
- 4.24 Forwarding to a number or voicemail
- 4.25 Cancelling all forwards
- 4.26 Listen to your voicemail
- 4.27 Defining a 'hotline' number
- 5 Do more with your deskphone
- 6 Programming your telephone
- 6.1 Adjusting the audio functions
- 6.2 Adjust ringer volume while a call arrives
- 6.3 Configuring the welcome page
- 6.4 Selecting language
- 6.5 Adjusting the contrast of the display
- 6.6 Programming direct call keys (8028s Premium DeskPhone, 8018 DeskPhone, add-on module)
- 6.7 Install a jack accessory (headset, hands-free, loudspeaker) (8028s)
- 6.8 Install a USB accessory (Headset, Handsfree, Loudspeaker)
- 6.9 Install a RJ9 headset (8008G, 8008)
- 6.10 Manage connected devices (8028s)
- 7 Contacting your administrator (technical support)
- 8 Accessories
- 9 Technical specifications
- 10 Ordering information
- 11 Guarantee and clauses
SIP Business
8AL90341ENACed01
47 /60
External ringing interface module (MWS 3GV28050AA)
8028s
8018
8008/8008G
The accessory is supported by the following sets
You have to use a RJ11 to SATA adapter to connect your deskphone to this device. The RJ11 to SATA
adaptator is sold separately (3MG07058AA).
The external ringing interface module allows driving an external system (like a ring or a lamp), following
the ring tone cadence of the phone set connected on the telephone line. A switch on the electronic board
allows selecting between 2 operation modes.
• Follows the cadence: the relay follows exactly the ring signal.
• Hold mode: the relay is held for 0,7 s after the ring signal is gone. It erases some of the
ring pulses.
List of supplies
• 1 external ringing interface module.
• 3 circuits plug to screw.
• 1 RJ11/RJ11 3 meters (10 feet) cable.
• 1 DC Japan/DC Japan 3 meters (10 feet) power cable.
A power supply may be required to power the module when used with IP phone powered remotely
(Power Over Ethernet).
Use only the following power supply (Sold separately):
• 3AK27097 (commercial part number).
• 1AF00446 (technical part number).
Installation
WARNING: The module must be closed before use. No settings require the module to be open.
In idle state:
The phone is ringing:
N: common.
NC: active signal.
NO: non-active signal.