Datasheet

2
Alcatel-Lucent OmniAccess 200 Series Access Points
ALCATEL-LUCENT ENTERPRISE DATA SHEET
AP200 SERIES SPECIFICATIONS
• AP205 and IAP205
¬ 2.4 GHz (300 Mb/s max rate) and 5 GHz
(867 Mb/s max rate) radios, each with
2 x 2 MIMO and four integrated omni-
directional downtilt antennas
• AP204 and IAP204
¬ 2.4 GHz (300 Mb/s max rate) and 5 GHz
(867 Mb/s max rate) radios, each with
2 x 2 MIMO and two combined, diplexed
external RP-SMA antenna connectors
ADVANCED FEATURES
• RF management
¬ Adaptive Radio Management™ (ARM)
technology automatically assigns
channel and power settings, provides
airtime fairness and ensures APs stay
clear of all sources of RF interference
to deliver reliable, high-performance
WLANs
¬ 200 Series APs can be congured to
provide part-time or dedicated air
monitoring for spectrum analysis and
wireless intrusion protection, virtual
private network (VPN) tunnels to extend
remote locations to corporate resources,
and wireless mesh connections where
Ethernet drops are not available
• Spectrum analysis
¬ Capable of part-time or dedicated air
monitoring, the spectrum analyzer
remotely scans the 2.4 GHz and 5 GHz
radio bands to identify sources of RF
interference
• Security
¬ Integrated Trusted Platform Module
(TPM) to securely store credentials
and keys
¬ SecureJack-capable to securely tunnel
wired Ethernet trafc
OPERATING MODES
• Instant AP
• Mobility Controller-managed AP
• RAP for branch deployments
• Air monitor (AM) for wireless intrusion
detection system (WIDS), rogue detection
and containment
• Spectrum analyzer, dedicated or hybrid
• Secure enterprise mesh
WIRELESS RADIO
SPECIFICATIONS
• AP type: Indoor, dual radio, 5 GHz
802.11ac and 2.4 GHz 802.11n 2 x 2:2
• Software-congurable dual radio supports
5 GHz (Radio 0) and 2.4 GHz (Radio 1)
• 2 x 2 MIMO with two spatial streams and
up to 867 Mb/s wireless data rate
• Supported frequency bands (country-
specic restrictions apply):
¬ 2.4000 GHz to 2.4835 GHz
¬ 5.150 GHz to 5.250 GHz
¬ 5.250 GHz to 5.350 GHz
¬ 5.470 GHz to 5.725 GHz
¬ 5.725 GHz to 5.850 GHz
• Available channels: Dependent on
congured regulatory domain
• Dynamic frequency selection (DFS)
optimizes available RF spectrum use
• Supported radio technologies:
¬ 802.11b: Direct-sequence spread
spectrum (DSSS)
¬ 802.11a/g/n/ac: Orthogonal frequency-
division multiplexing (OFDM)
• Supported modulation types:
¬ 802.11b: Binary phase-shift keying
(BPSK), quadrature phase shift keying
(QPSK), Complementary Code Keying
(CCK)
¬ 802.11a/g/n/ac: BPSK, QPSK, 16-QAM,
64-QAM, 256-QAM
• Transmit power: Congurable in
increments of 0.5 dBm
• Maximum (aggregate, conducted total)
transmit power (limited by local regulatory
requirements):
¬ 2.4 GHz band: +21 dBm
(18 dBm per chain)
¬ 5 GHz band: +21 dBm
(18 dBm per chain)
• Advanced Cellular Coexistence (ACC)
minimizes interference from cellular
networks
• Maximum ratio combining (MRC)
for improved receiver performance
• Cyclic delay/shift diversity (CDD/CSD)
for improved downlink RF performance
• Short guard interval for 20 MHz, 40 MHz
and 80 MHz channels
• Space-time block coding (STBC) for
increased range and improved reception
• Low-density parity check (LDPC) for high-
efciency error correction and increased
throughput
• Transmit beamforming (TxBF) for
increased reliability in signal delivery
• Supported data rates (Mb/s):
¬ 802.11b: 1, 2, 5.5, 11
¬ 802.11a/g: 6, 9, 12, 18, 24, 36, 48, 54
¬ 802.11n: 6.5 to 300 (MCS0 to MCS15)
¬ 802.11ac: 6.5 to 867 (MCS0 to MCS9,
NSS = 1 to 2)
• 802.11n high-throughput (HT) support:
HT 20/40
• 802.11ac very high throughput (VHT)
support: VHT 20/40/80
• 802.11n/ac packet aggregation: A-MPDu,
A-MSDu
Antennas
• AP204/IAP204: Two RP-SMA connectors
for external dual-band antennas. Internal
loss between radio interface and external
antenna connectors (due to diplexing
circuitry): 1.5 dB in 2.4 GHz and 3.0 dB
in 5 GHz
• AP205/IAP205: Four integrated down-tilt
omni- directional antennas for 2 x 2 MIMO
with maximum antenna gain of 4.0 dBi
in 2.4 GHz and 6.0 dBi in 5 GHz. built-in
antennas are optimized for horizontal
ceiling-mounted orientation of the AP
OTHER INTERFACES
• 10/100/1000BASE-T Ethernet network
interface (RJ-45)
¬ Auto-sensing link speed and MDI/MDX
¬ 802.3az Energy-Efcient Ethernet (EEE)
¬ Power over Ethernet (PoE)-PD: 48-V DC
(nominal) 802.3af PoE
• DC power interface, accepts 1.7 mm/
4.0 mm center-positive circular plug with
9.5 mm length
• Visual indicators (LEDs):
¬ Power/system status
¬ Ethernet link status (ENET)
¬ Radio status (two; RAD0, RAD1)
• Reset button: factory reset (during device
power up)
• Serial console interface (RJ-45)
• Kensington security slot
POWER
• Maximum (worst-case) power
consumption: 12.5 W (PoE) or 11.7 W (DC)
• Maximum (worst-case) power consumption
in idle mode: 8.4 W (PoE) or 7.7 W (DC)
• Direct DC source: 12-V DC nominal, +/- 5%
• PoE: 48-V DC (nominal) 802.3af-compliant
source
• Power sources sold separately
• When both power sources are available,
DC power takes priority