Specifications

Alcatel-Lucent
OS-LS6200 Series Page 14
speed is 10/100Mbps. When operating in 1000Mbps only full duplex mode is supported
The 10/100/1000BASE-T ports support auto-sensing, and auto-negotiation.
Auto-negotiating 10/100/1000 ports automatically configure port speed and duplex settings
Auto MDI/MDIX automatically configures transmit and receive signals to support straight through and
crossover cabling for connection to various network devices
MDI/MDIX Support The device automatically detects whether the cable connected to an RJ-45 port is crossed or straight
through. Standard wiring for end stations is Media-Dependent Interface (MDI) and the standard wiring
for hubs and switches is known as Media-Dependent Interface with Crossover (MDIX).
Auto Negotiation Auto negotiation allows the device to advertise modes of operation. The auto negotiation function
provides the means to exchange information between two devices that share a point-to-point link
segment, and to automatically configure both devices to take maximum advantage of their transmission
capabilities. Auto-negotiation advertisement is also supported. Port advertisement allows the system
administrator to configure the port speed and duplex advertised.
Uplink capabilities (Combo ports) • OS LS 6200: Two Gigabit Ethernet SFP (mini-GBIC) plus two 10/100/1000 RJ-45 combo ports are
located on the front panel. Users determine whether the mini-GBIC or 10/100/1000 ports will operate.
The mini-GBIC ports support full duplex mode only.
• SFP (mini-GBIC) ports support 100Base FX fiber optic transceivers for 100mb fiber connectivity
Stacking ports • OS LS 6200: Two 10/100/1000 copper RJ-45 ports. OS LS 6200 supports a fault tolerant looped
stacking configuration. In a standalone configuration, these ports can be used as normal network ports.
Indicators • LEDs per port:
• 10/100: link/activity, PoE power
• Combo: Link/activity
• 10/100/1000: Link/activity
• System LEDs:
• OK (Diagnostics)
• PWR (Internal power supply status)
• FAN (Fan status)
• TEMP (Over-Temp.)
• RPU (Backup power status)
• Stack (Status)
Gigabit Ethernet Transceivers (SFP MSA)
Compliant with “SFP-MSA”, IEEE 802.3z, and hot swappable & hot insertable:
SFP-GIG-EXTND Extended 1000Base-SX Gigabit Ethernet optical transceiver (SFP MSA). Supports multimode fiber
over 850nm wavelength (nominal) with an LC connector. Reach of up to 2 km (based on grade and
condition of fiber) on 62.5/125 µm MMF or 550m on 62.5/125 µm MMF. Requires SFP-GIG-EXTND
or GBIC-GIG-EXTND at the remote termination.
[Formerly known as GE-EXTND-SFP]
SFP-GIG-LH40 1000Base-LH Gigabit Ethernet optical transceiver (SFP MSA). Supports single mode fiber over 1310
nm wavelength (nominal) with an LC connector. Typical reach of 40 Km on 9/125 µm SMF.
SFP-GIG-LH70 1000Base-LH Gigabit Ethernet optical transceiver (SFP MSA). Supports single mode fiber over
1550nm wavelength (nominal) with an LC connector. Typical reach of 70 Km on 9/125 µm SMF.
[Formerly known as MINIGBIC-LH-70]
SFP-GIG-LX 1000Base-LX Gigabit Ethernet optical transceiver (SFP MSA). Supports single mode fiber over
1310nm wavelength (nominal) with an LC connector. Typical reach of 10 Km on 9/125 µm SMF.
[Formerly known as MINIGBIC-LX]
SFP-GIG-SX 1000Base-SX Gigabit Ethernet optical transceiver (SFP MSA). Supports multimode fiber over 850nm
wavelength (nominal) with an LC connector. Typical reach of 300m on 62.5/125 µm MMF or 550m
on 50/125 µm MMF. [Formerly known as MINIGBIC-SX]
100 FX Ethernet Transceivers
100Base-FX fiber optic transceiver options supported
(Maintenance Software Release)
The OmniStack LS 6200 hardware can support
100Base-FX transceivers using the SFP (mini-GBIC)
ports. Software support will be provided in a
maintenance release.
SFP-100-LC-MM: 100BASE-FM short haul multimode 62.5/125µm and 50/125µm fiber, supports
distances up to 2km; uses LC connectors, full duplex
SFP-100-LC-SM15: 100BASE-FS long haul single mode 9/125µm fiber, supports distances up to 15
km; uses LC connectors, full duplex
SFP-100-LC-SM40: 100BASE-FS long haul single mode 9/125µm fiber, supports distances up to 40
km; uses LC connectors, full duplex
SFP-100-BX20LT 100Base-BX SFP transceiver with an SC type interface. This bi-directional transceiver is designed for
use over single mode fiber optic on a single strand link up to 20KM point-to-point. This transceiver is
normally used in the central office (OLT) transmits 1550nm and receives 1310nm optical signal
SFP-100-BX20NU 100Base-BX SFP transceiver with an SC type interface. This bi-directional transceiver is designed for
use over single mode fiber optic on a single strand link up to 20KM point-to-point. This transceiver is
normally used in the client (ONU) transmits 1310nm and receives 1550nm optical signal
SFP-100-LC-MM 100Base-FX SFP transceiver with an LC type interface. This transceiver is designed for
use over multimode fiber optic cable.
SFP-100-LC-SM15 100Base-FX SFP transceiver with an LC type interface. This transceiver is designed for use over single
mode fiber optic cable up to 15KM.
SFP-100-LC-SM40 100Base-FX SFP transceiver with an LC type interface. This transceiver is designed for use over single
mode fiber optic cable up to 40KM.