060355-10 Rev. D June 2013 OmniSwitch 6250/6450 Transceivers Guide www.alcatel-lucent.
This user guide contains transceiver specifications and compatibility information for the OmniSwitch 6250/6450 switches. The information described in this guide is subject to change without notice. Attention: Use of any transceivers other than those part numbers listed in the Compatibility Matrices is prohibited. Failure to comply with these matrices is not guaranteed for proper performance and may result in voiding the warranty for the affected platforms. Copyright © 2013 by Alcatel-Lucent.
Contents Contents About This Guide ........................................................................................................... v Supported Platforms ........................................................................................................... v Who Should Read this Manual? ........................................................................................ vi When Should I Read this Manual? ..................................................................................
About This Guide Supported Platforms About This Guide This OmniSwitch Transceivers Guide provides specifications and compatibility information on the supported transceivers for the OmniSwitch 6250 and OmniSwitch 6450.
Who Should Read this Manual? About This Guide Who Should Read this Manual? The audience for this user guide is network administrators and IT support personnel who need to provide network connectivity using SFP transceivers on an OmniSwitch. When Should I Read this Manual? Read this guide as soon as you are ready to integrate your OmniSwitch into your network and you are ready to provide connectivity using the supported transceivers.
About This Guide Documentation Roadmap Documentation Roadmap The OmniSwitch user documentation suite was designed to supply you with information at several critical junctures of the configuration process. The following section outlines a roadmap of the manuals that will help you at each stage of the configuration process. Under each stage, we point you to the manual or manuals that will be most helpful to you.
Related Documentation The following are the titles and descriptions of all the related OmniSwitch AOS Release 6 user manuals: • OmniSwitch 6250 Getting Started Guide Describes the basic information you need to unpack and identify the components of your OmniSwitch shipment. Also provides information on the initial configuration of the switch. • OmniSwitch 6250 Hardware Users Guide • Detailed technical specifications and procedures for the chassis and components.
All products are shipped with a Product Documentation Card that provides details for downloading documentation for all OmniSwitch and other Alcatel-Lucent data enterprise products. All documentation is in PDF format and requires the Adobe Acrobat Reader program for viewing. Acrobat Reader freeware is available at www.adobe.com. Note. When printing pages from the documentation PDFs, de-select Fit to Page if it is selected in your print dialog. Otherwise pages may print with slightly smaller margins.
Documentation Feedback page x About This Guide OmniSwitch 6250/6450 Transceivers Guide
1 Small Form-Factor Pluggables (SFPs) OmniSwitch switches use both copper-based and fiber-based optical Small Form Factor Pluggable (SFP) transceivers. SFPs are fully hot-swappable and are available for both short-reach and long-reach applications. Copper-based and fiber-based optical SFPs can be mixed on the same module. In This Chapter This chapter describes the technical specifications for all the OmniSwitch supported SFP transceivers.
SFP MSA Specification Small Form-Factor Pluggables (SFPs) SFP MSA Specification The Small Form-Factor Pluggable (SFP) MSA (Multi Source Agreement) is a specification for a common interface for optical modular transceivers. The SFP connector consists of a 20-pin receptacle and an SFP housing cage. The connector provides the interface for the hot pluggable SFP module.
Small Form-Factor Pluggables (SFPs) SFP Transceiver Installation and Removal SFP Transceiver Installation and Removal Follow the instructions below for the appropriate SFP type. ESD Caution: Before handling the module, you must discharge all static electricity on your person to avoid Electrostatic Discharge (ESD) damage. If using a wrist strap, ensure that the wrist strap touches your skin. Attach the other end of the strap to the chassis. If your chassis provides a grounding lug, this can be used.
SFP Transceiver Installation and Removal Small Form-Factor Pluggables (SFPs) To install, align the transceiver with the transceiver slot on the NI module, as shown. Be sure that the bail wire delatch is in the up, or closed position. Slide the transceiver straight into the slot until the module clicks firmly into place. To remove, you must first pull down on the bail wire delatch. Grip the wire delatch while it is in this open position and carefully pull the transceiver straight out of the slot.
Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers Gigabit Ethernet Transceivers SFP-GIG-SX Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -9.5 to -4 dBm Receiver Sensitivity -17 dBm Transmission Distance ~275 m on 62.
SFP-GIG-LH40 Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000Base-LH40 Fiber Type SMF Wavelength 1310 nm Optical Power Output -2 to +3 dBm Reciever Sensitivity -22 dBm Transmission Distance ~40 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-GIG-LH70 Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.
SFP-GIG-EXTND Gigabit SFP Optical Transceiver. Connector Type LC Standards Supported 802.3, SFP MSA Connections Supported - Fiber Type MMF Wavelength 1310 nm Saturation Power Output 0 dBm Transmission Distance ~2 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-GIG-T Gigabit SFP Copper Transceiver. Connector Type RJ-45 Standards Supported 802.
Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs) SFP-GIG-BX-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA Connections Supported 1000Base-BX10 Fiber Type SMF Wavelength Transmit: 1490 mm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -19.
Small Form-Factor Pluggables (SFPs) Gigabit Ethernet Transceivers SFP-GIG-BX-D20 Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Gigabit Ethernet Transceivers Small Form-Factor Pluggables (SFPs) SFP-GIG-CWD Coarse Wavelength Division Multiplexing (CWDM) is an optical transceiver supporting single-mode fiber over various wavelengths. CWDMs are hot-pluggable and are available for long-reach applications. Connector Type LC Standards Supported 802.
Small Form-Factor Pluggables (SFPs) 100 Mbit Ethernet Transceivers 100 Mbit Ethernet Transceivers SFP-100-BX20LT Bi-Directional SFP Optical Transceiver. Connector Type SC Standards Supported 802.3ah, SFP MSA, ITU-T G.
SFP-100-BXLC-D Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3ah, SFP MSA, ITU-T G.983 Connections Supported 100Base-BX Fiber Type SMF Wavelength Transmit: 1550 mm Receive: 1310 nm Average Power Output -14 to -8 dBm Receiver Sensitivity -32 dBm Transmission Distance ~20 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported Notes Designed for use with SFP-100-BXLC-U SFP-100-BXLC-U Bi-Directional SFP Optical Transceiver.
SFP-100-LC-MM SFP Optical Transceiver. Connector Type LC Standards Supported 802.3u, SFP MSA Connections supported 100Base-FX Fiber Type MMF Wavelength 1310 nm Optical Power Output -19 to -14 dBm on 62.5/125µm -22 to -14 dBm on 50/125µm Transmission Distance ~2 km on 62.5/125µm ~2 km on 50/125µm Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported SFP-100-LC-SM15 SFP Optical Transceiver. Connector Type LC Standards Supported 802.
SFP-100-LC-SM40 SFP Optical Transceiver. Connector Type LC Standards Supported 802.
Dual-Speed Ethernet Transceivers SFP-DUAL-BX-D Dual-Speed Bi-Directional SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, SFP MSA Connections Supported 1000BASE-BX10-D Fiber Type SMF Wavelength Transmit: 1550 nm Receive: 1310 nm Average Power Output -9 to -3 dBm Receiver Sensitivity -18.7 dBm Transmission Distance ~ 10 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Not Supported SFP-DUAL-BX-U Dual-Speed Bi-Directional SFP Optical Transceiver.
SFP-DUAL-SM10 Dual-Speed SFP Optical Transceiver. Connector Type LC Standards Supported 802.3z, 802.3ah, SFP MSA Connections Supported 100Base-LX, 1000Base-LX Fiber Type SMF Wavelength 1310 nm Average Power Output 100Base-LX: -15 to -8 dBm 1000Base-LX: -9.
Small Form-Factor Pluggables (SFPs) 10-Gigabit SFP+ Transceivers 10-Gigabit SFP+ Transceivers SFP-10G-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3 Clause 52 Connections supported 10GBase-SR Fiber Type MMF Wavelength 850 nm Optical Power Output -7.3 to -1.3 dBm Receiver Sensitivity -11.1 dBm Transmission Distance ~ 300 m Operating Temperature 0 ºC to 70ºC Digital Diagnostic Monitoring Supported SFP-10G-LR 10-Gigabit SFP+ Optical Transceiver.
SFP-10G-ER 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3ae Connections supported 10GBase-E Fiber Type SMF Wavelength 1550 nm Optical Power Output -4.7 to 4.0 dBm Receiver Sensitivity -14.1 dBm Transmission Distance ~ 40 km Operating Temperature 0 ºC to 70 ºC Digital Diagnostic Monitoring Supported SFP-10G-LRM 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.
SFP-10G-C 10-Gigabit SFP+ Copper Transceiver. Connector Type Direct Attached Standards Supported 802.3ae Cable Length 60cm, 1m, 3m, 7m1 Wire Gauge 24AWG Bend Radius 1.25 in. Digital Diagnostic Monitoring Not Supported 1 Check for availability of lengths. SFP-10G-GIG-SR 10-Gigabit SFP+ Optical Transceiver. Connector Type LC Standards Supported 802.3-2005 Connections supported 10GBase-SR/SW, 1000Base-SX Fiber Type MMF Wavelength 850 nm Optical Power Output -5 to -1 @ 10G -9.
OmniSwitch 6250 SFP Compatibility Matrix SFP Compatibility Matrix OmniSwitch 6250 The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6250: SFP OS6250 SFP-GIG-SX 6.6.1 SFP-GIG-LX 6.6.1 SFP-GIG-LH40 6.6.1 SFP-GIG-LH70 6.6.1 SFP-GIG-EXTND 6.6.1 SFP-GIG-T 6.6.1 SFP-GIG-BX-D 6.6.1 SFP-GIG-BX-U 6.6.1 SFP-GIG-BX-D20 Not Supported SFP-GIG-BX-U20 Not Supported SFP-GIG-CWD Not Supported 1 6.6.1 SFP-100-BX20NU1 6.
SFP SFP-10G-GIG-SR 1. Only supported on combo ports @ 100Mbps speed.
OmniSwitch 6450 The following table shows the Ethernet transceiver configurations and the minimum release required for support on the OmniSwitch 6450: SFP OS6450 SFP-GIG-SX 6.6.3 SFP-GIG-LX 6.6.3 SFP-GIG-LH40 6.6.3 SFP-GIG-LH70 6.6.3 SFP-GIG-EXTND 6.6.4 SFP-GIG-T1 6.6.3 SFP-GIG-BX-D 6.6.3 SFP-GIG-BX-U 6.6.3 SFP-GIG-BX-D20 6.6.4 SFP-GIG-BX-U20 6.6.4 SFP-GIG-CWD 6.6.3 SFP-100-BX20LT2 6.6.3 2 6.6.3 SFP-100-BXLC-D2 6.6.3 2 6.6.3 2 6.6.
