Operation Manual

SAFETY
In the event of an electrical hazard, the mains adapter acts as 230V power isolating device. It should therefore, as a
precaution, be installed close to the appliance and be easily accessible. To disconnect the device from the primary power
source, the mains adapter must be removed from the 230V AC / 50 Hz socket.
If the mains adapter fails, it must be replaced by an identical model.
If not connected to the mains power or if there is a mains power failure, telephones that use cordless handsets will not
work.
You will then be unable to make or receive calls in the event of an emergency.
This is why we recommend that you also keep a conventional telephone – one that doesn’t require a power supply – as a
backup.
! Do not use your telephone to notify a gas leak when standing in the vicinity of the leak.
It is recommended that you avoid using this device during electrical storms.
Do not attempt to open the batteries, as they contain chemical substances. In the event of leakage, avoid contact with the
skin, eyes, nose and mouth. In the event of contact, rinse the affected part for about twenty minutes with running water
and seek urgent medical attention. Clean the product with absorbent paper or a dry cloth and contact your reseller for
replacement batteries.
ATLINKS hereby declares that the following models conform to the essential requirements and other applicable provisions
of European directive 1999/5/EC.
Alcatel XS
ENVIRONMENT
This symbol means that your inoperative electronic appliance must be collected separately and not mixed
with the household waste. The European Union has implemented a specific collection and recycling system
for which producers are responsible.
This appliance has been designed and manufactured with high quality materials and components that can be recycled
and reused. Electrical and electronic appliances are liable to contain parts that are necessary in order for the system to
work properly but which can become a health and environmental hazard if they are not handled or disposed of in the
proper way. Consequently, please do not throw out your inoperative appliance with the household waste.
If you are the owner of the appliance, you must deposit it at the appropriate local collection point or leave it with the
vendor when buying a new appliance.
- If you are a professional user, please follow your supplier's instructions.
- If the appliance is rented to you or left in your care, please contact your service provider.
Keen to preserve the environment, ATLINKS has equipped this appliance with a switching power supply, offering better
energy efficiency. The advantages include not only very low electricity consumption, but also a more compact format than
the conventional power supply units used by the previous range.
The used batteries from your telephone (if it has batteries) must be disposed of in compliance with current environmental
protection regulations. Comply with your local regulations.
Return your batteries to your reseller or dispose of them at an approved recycling centre.
Help us protect the environment in which we live!
TABLE 1: PROGRAMMING SETTING
Remark:
To reset all previous parameters to default settings, you can do it from the Alcatel XS itself.
1) Ringer volume reset to level 3,
2) Ringer melody to 3,
3) All 3 memories to empty.
TABLE 2: COLOR OF LED INDICATION
TABLE 3: TONE INDICATION
TABLE 4: TECHNICAL DETAILS
* Values may vary according to environment.
** Depending on initial battery charge.
TROUBLESHOOTING
If you have difficulty with your phone, please try the suggestions listed below.
www.alcatel-home.com
ATLINKS Europe
22 quai Gallieni
92150 Suresnes- France
© ATLINKS 2012 - Reproduction prohibited.
The Manufacturer reserves the right to modify the specifications of its products in order to make technical improvements
or comply with new regulations.
ALCATEL, VERSATIS and ATLINKS are registered trademarks.
The Alcatel logo and Alcatel name are trademarks of Alcatel Lucent and used under license by ATLINKS.
ALCATEL XS
A/W No.: 10000587 Rev.0 (EN)
The store where you bought your telephone can also provide you with information and after-sales support.
LED Color Behavior Description
Rapid Blink Out of range
During Power On, or Idle mode (per 32 seconds), or Incoming call,
or In Use
(remark: speed of blink is slightly different in each above conditions)
Steady On Programming mode
Registration mode, or
Low Battery level
Steady On
Reset Mode
Charging (always on even if Battery is full)
Blink Unregister Mode
Blue
Blink
Red
Steady On
Violet
Blink
Tone Type Behavior Description
Key Tone One Short Beep Alert when key press
Confirmation Tone One Short Beep
Alert in programming mode when press # to confirm any settings or,
when press # to save editing
Error Tone Two Consequence Short Beep
Alert In programming mode when invalid value is entered
(e.g. Phone Settings) or when registration fail
Low Battery Tone Two Consequence Short Beep Alert when low battery
Out Of Range Tone Two Consequence Short Beep Alert when out of range.
On Cradle Tone
One Short Beep Alert when on cradle
Up to 300 metres*
Up to 50 metres*
4 hours talk time**
100 hours standby**
Charger adaptor:
Input: 100-240 V/50-60 Hz/0.15 A
Output: 6 V DC/500 mA
Only use the adaptors supplied with the telephone
Single-phase AC, excluding IT installations defined by the EN60950 standard.
Caution: The network voltage is classified as a hazard by the criteria of this standard.
From 5ºC to 40ºC
Free Field Range
Indoor Range
Handset Battery Life
(average values)
Batteries
Operating Temperature
Electrical Connection / Charger
Problem Cause Solutions
a. The connection cord of the base
station is not plugged in.
a. Check the connections. Unplug and plug back in the mains.
Check that the telephone line cord has been plugged into the
base station and the phone socket.
b. The adapter cord is not plugged
in correctly in the base station.
b. Check the base station plug and the 230V plug (remove and
plug-in).
c. The line is busy, as another
handset is used.
c. Wait until the line is unoccupied.
d. Wrong connection cord
(no Euro AS)
d. Use the original connection cord.
e. XS is not yet registered with the
base.
e. Register XS with the base as per section 4.1.
a. Base station out of range.
b. Base station not connected to
mains.
c. XS out of range.
The call does not
work.
Service not activated or wrong
operator or wrong setting
Reduce the range of base and XS.
Connect base station to mains.
No LED indication.
Empty battery
Put XS into the charger
Two short tone
beeps every 10
seconds & Red
LED is double
blinking
Insert the dialing prefix
No dialing tone
when pressing
key
Menu name Action
Secuencia en el teclado alfanumérico
Ringer volume
control
Ring volume control
Ringtones on
handset
Choose ringer
melody
press " 01" + "number(20 digits in length)" + "#" (complete by hearing a
confirmation tone )
Quick dial Program M1
Quick dial Program M2
Quick dial Program M3
Registration
to be described in
Section 4.1
Reset all parameters
to default (see
remark under table 1)
Manual registration
press " 07" + pin number +"#" (complete by hearing a confirmation tone )
Pin Code Number
Change registration
PIN code
Long press key and for 3 seconds at the same time (complete by hearing a
confirmation tone).
Check your Subscription with network or change the dial mode.
When connect to a
PBX, no and/or
wrong connection
after dialing.
Dialing prefix is needed.
AAA – 1,2 V – 300 mA
Only use the batteries supplied with the XS.
Use any other type of battery presents a risk of explosion. Used batteries must be
disposed of in compliance with current environmental protection regulations.
press " 05" + " "value" +"#" (complete by hearing a confirmation tone);
value = 0 to 5
Wait the end of the melody for selecting another volume.
press " 02" + "number(20 digits in length)" + "#" (complete by hearing a
confirmation tone )
press " 03" + "number(20 digits in length)" + "#" (complete by hearing a
confirmation tone )
press " 04" + " "value" +"#" (complete by hearing a confirmation tone);
value = 1 to 5
Wait the end of the melody for selecting another volume.
Default settings
You can change Pin number to 4 digits number.
The default Pin number is “0000”, 4 digits in length.
Press " 22" + pin number +"#" (complete by hearing a confirmation tone )