User's Manual

8
Connect a Bluetooth® device to the Main Unit
To Adjust the Volume
The volume can be adjusted using the Master Volume Knob on the
main unit, or the Volume Up/Down Buttons on the remote control.
For Personal Listening
Connect headphones (Ø3.5mm stereo mini plug) to the earphone
jack. Adjust the VOLUME levels to obtain the desired volume.
When headphones are connected, the speakers are automatically
muted.
Warning: Excessive sound pressure from earphones and headphones
can cause hearing loss.
Listen to the Radio
1. Press the button to turn the unit on.
2. Press the
button to FM mode.
3. Press the or button to tune in to a station.
4. Adjust the volume levels.
Searching for a Station Automatically
• Press and hold the or button until the tuner starts searching
for a station, then release. After tuning in a station, the search
stops.
• The search may not stop at a station with a very weak signal.
Presetting Stations
The unit can store a total of 20 stations in memory. Presetting allows
you to tune in to a station directly.
1. Tune in to a desired station.
2. Press and hold the MEMORY button. The preset number will blink
and the “PXX” indicator will be shown on the display.
3. Press the
or button to select the preset number.
4. Press the MEMORY button again to store it in memory.
5. Repeat steps 1-4 to store other stations.
Tuning into a Preset Station
Press PLAY/PAUSE button on the unit or press or button on
the remote control to select a preset number.
For Better reception
FM: Fully unwind the antenna wire. Extend the antenna wire and
place it in the position that sounds best.
Note: Do not connect the FM antenna to an outside antenna.
Volume Adjustment
This system supports a variety of equalizers and sound effects.
During playback, press the EQ button to select a desired music
mode. Each time the EQ button is pressed, the music mode will be
changed to the next one as follows:
POP / CLASSIC / FLAT / JAZZ
Preset EQ
You can connect audio devices such as your iPod, CD players or MP3
players to the unit via the LINE IN jack. To do this, connect an audio
cable from the line out or headphone out jack of the other audio
device to the LINE IN jack on the unit’s front panel.
Listening to the Connected Device
1. Press the
button to LINE IN mode and “ L-in ” is shown on the
display.
2. Turn on the audio device you’ve attached to the LINE IN jack.
Line-In Playback
1. Press the button to turn on the unit.
2. Press the button to CD mode.
3. Press the button to open the CD door. Place a disc in the center
with the label side up and then press the button again to close
the CD door. Then, it plays automatically.
• Adjust the volume levels.
To Pause Playback
• Press the button.
• To resume playback, press the
button again.
To Stop Playback
• Press the button.
Skipping to Another Track
• Press either the or button according to the desired
direction.
• Press the button to skip to the start of the current track or skip
to previous tracks. Press the button to skip to the beginning
of the next track.
Locating a Particular Point on a Track
• Keep either the or button pressed during playback,
according to the desired direction, and release at the desired
point.
CD Playback
Settings
WIRELESS & NETWORKS
Wi-Fi
Bluetooth
More...
DEVICE
ScreenshotSetting
Storage
Battery
SEARCH FOR DEVICES
Hdmi
Sound
Display
6:14
ON
RCA RCS13101E
RCS13101T
Not visible to other Bluetooth device
AVAILABLE DEVICES
ON
The system can wirelessly receive and playback audio from a
Bluetooth-equipped smartphone, tablet, or computer.
1. Go to Settings > WIRELESS & NETWORKS > BLUETOOTH, and
slide the Bluetooth® switch to the ON position.
2. Turn on the Bluetooth® device you wish to pair and connect.
3. On your Bluetooth® enabled device, search for the “RCA
RCS13101E" in the list of discovered devices and select it.
Note: If your Bluetooth
®
device (e.g. Smart phone etc.) need the
PIN code while pairing, please enter 4-digit number: 0000.
The Bluetooth
®
word mark and logos
are registered trademarks owned by
Bluetooth SIG, Inc.