MIDDLE RANGE RF TELECOM SYSTEM STATlON TO STATION STATION TO MOBILE OPERATION GUIDE
TABLE OF CONTENTS ALCON-7 FEATURES .....................................................................................................................3 STANDARD PACKAGE...................................................................................................................4 FUNCTION KEYS............................................................................................................................5 ANSWERING A CALL .....................................................................
FEATURES: ♦ POINT-TO-POINT OR POINT-TO-MOBlLE USE ♦ HIGH PERFORMANCE ♦ UNlVERSAL INTERFACE ON THE REMOTE/MOBILE FOR FAX / DATA OR OTHER TELECOM EQUIPMENT USE ♦ ECONOMlCAL AND EASY TO USE ♦ EXCELLENT SIGNAL QUALITY FOR LONG RANGE USE ♦ RF STABlLITY & DURABILlTY ♦ SCRAMBLER FUNCTlON ♦ 4O CHANNELS FREQUENCY AUTO SCAN ♦ TWO-WAY PAGING & lNTERCOM ♦ MODULAR DESIGN STANDARD PACKAGE ALCON-7 BASE UNIT AND REMOTE / MOBILE Standard Accessories for ALCON-7 S.S.
Standard Accessories for ALCON-7 S.M. Base Unit Remote / Mobile Unit Switching Adaptor 5DFB 20m Cable A-7 Antenna AT-80 Telephone 1/2 λ Car Antenna Magnetic Car Antenna Mount DC Cord User’s Manual x1 x1 x1 x1 x1 x1 x1 x1 x1 x1 Standard Accessories for ALCON-7 S.M.
FUNCTION KEYS : Base Unit REDIAL FLASH HOLD CONF Redial Key Flash Key Hold Key Three-Way Conference Call Speakerphone Key Remote/Mobile Unit Scramble Intercom Scramble Key Intercom Key Scramble Key Intercom Key Scramble indicator Intercom indicator In Use indicator Power indicator Flash Key Hold Key Redial Key Three-Way Conference Call Intercom Key Speakerphone Key 5
ANSWERING A CALL ANSWERING WITH THE ALCON-7 Remote Unit Make sure the Remote POWER switch is ON. 1. When a call comes in, the Normal Telephone will ring. The TEL indicator will flash. 2. Pick-up the handset of the Normal Telephone and begin your conversation. The TEL indicator will illuminate. 3. Hang up . ANSWERING WITH THE BASE UNIT There are two methods to answer a call with the base unit: A. Picking up the Handset from the Base Unit B. Using the Speakerphone (Hands-Free) A.
RINGER VOLUME CONTROL RINGER ON/OFF SWITCH Set the RINGER switch on the middle right side of the base unit to ON (up) or OFF (down). VOLUME CONTROL SCRAMBLE FUNCTION To prevent somebody from eavesdropping on your conversation, use the Scramble function. . 1. Press the Scrambler button located on the front of the remote unit to engage the scramble function. When the SCRAM indicator is illuminated, the scramble function has engaged. 2. Press the Scramble button again to disengage the scramble function.
BASE UNIT There are two methods to place a call using the base unit. A. Picking up the Receiver from the Base 1 2 Unit 1. Listen for a dial tone by lifting the Receiver from the base unit. The TEL indicator and dialing buttons (green light) will illuminate. 2.Dial the number you want to call. When you press the digit buttons, the buttons that are being pressed will turn from green to red. 3.Return the Receiver to the base unit after finishing a conversation. B. Using the Speakerphone 1.
INTERCOM FUNCTION {BETWEEN REMOTE/ MOBILE UNIT AND BASE UNIT} A : Remote / Mobile CALLING BASE UNIT Remote / Mobile 1. Press INTERCOM. The base will emit two short “beeps”. The Remote/Mobile unit INT indicator will begin to flash. 2. Lift the telephone handset and wait for somebody to activate the Base Unit. Once the Base unit is in use, the INT indicator will continuously illuminate. 3. To finish the conversation, return the handset to the Base unit.
Remote/ Mobile unit 1. The Remote/ Mobile unit will ring. The INT indicator will flash. This means that the Base unit is calling the Remote/ Mobile unit. 2. Once you lift the telephone handset, you can begin you conversation . The INT indicator will continuously illuminate. 3. To finish the conversation, press CALL or hang up the telephone handset of Remote/ Mobile unit.
3-WAY CONFERENCE CALLS BETWEEN THE BASE UNIT AND REMOTE/ MOBILE UNIT AND OUTSIDE CALL OR BASE UNIT CALLING THE REMOTE UNIT 3 DURING AN OUTSIDE CALL 1 Base Unit 1.Press Hold button. 2 The TEL indicator will flash. 2. Press CALL. The CALL indicator will illuminate. 3. Press 1 (it means calling the Remote/ Mobile unit) The CALL indicator will illuminate and the digit button no. 1 will flash. They will illuminate during the conversation. Remote/Mobile 1.The telephone set of Remote/ Mobile unit will ring.
REDIAL FUNCTION You can redial the last telephone number dialed automatically {after getting a busy signal, for instance} Base Unit 1. Pick up the receiver of the base unit or press to get a dial tone. 2 The TEL key will illuminate. If you use, it will illuminate as well. 2. Press REDIAL. 1 The last telephone number dialed from the handset will be dialed out automatically. Remote/ Mobile Unit It depends on whether the telephone set that is being used with the Remote/Mobile Unit has this function.
FLASH FUNCTION The FLASH button can be used to get a new dial tone without pressing . You can also use the flash function to obtain special services, such as Call Waiting from your local PTT or PBX. If you subscribe to “Call Waiting” : 1. When a call comes in when you are in an outside call conversation, you will hear a soft “do-do” sound. 2. Press FLASH. The first caller is put on hold and you can converse with the second caller. 3. Press FLASH again to talk to the first caller.
NOTE : ● Once you press the digit button, you must complete the following procedures within 5 seconds to saccessfally complete the procedure. Remote/ Mobile Unit 2. Press INTERCOM (without letting go) and switch POWER to ON. The POWER, TEL, IN USE, INT, and SCRAM indicator will illuminate meaning that your procedure has been successfully completed. 3. Switch POWER of Remote/ Mobile unit to OFF, and then switch to ON. 4.
Bringing People Together Printed in Taiwan
