High Quality Cordlessphone System ALCON-73BH User Manual Ver. 1.
Table of Contents ALCON-73BH Features………………………………………….……………………………………………...…………………3 Standard Package……………………………………………………………………………………….……….………………….3 Base Unit Function keys……………………………………………………….…………………………….…………………..4 Handset Unit Function keys………………………………………………….………………………….……………………..4 Function Explanation…………………………………………………………….………………………………………………..5 Answering a Call …………………………………………………………………………………………………………….5 Placing a Call ………………………………………………………………………..………………………………………..
Features ● Multi-Handset Cordless Telephone ● More powerful Handset ● Full duplex intercom ● Hold music ● Last number redial for Handset only ● Backlighting on handset keypad ● 40-channel auto scan ● Touch any key answer function for handset ● 12-number memory for each handset ( 15 digits ) ● Handset Low battery indication ● Built-in noise cancellation circuit ( compander ) ● Handset scramble function ● Hands-free headset ( optional ) ● Manual handset channel change function if interference occurs during o
Base Unit Function Keys 9 1. 2. 3. 4. 1 2 3 4 5 6 7 8 10 Power indicator In Use indicator Intercom indicator Scramble indicator 5. ~ 8. Select Button Handset No.1~4 indicator 9. Select Button 10. Intercom Button Handset Unit Function Keys J Off Low Hi K A D B E C F 1 2 3 4 5 6 7 8 9 * 0 # G H I L A. Redial Key B. Flash Key C. Hold key D. Intercom key E. End Call Key F. Call Key G. Telephone Number Memory Key H. ~ I. Handset Receiver Volume Control Key J.
Function Explanation ANSWERING A CALL ANSWERING With the HANDSET 1. When a call comes in, the handset will ring. The TEL indicator, dialing buttons and handset indicators will flash. 2. Begin your conversation by pressing any key on the handset. 1 3 The TEL indicator will illuminate. 3. To hang up, press There is a MUTE button on the right side of the handset. The person who is on the other side of the conversation won’t be able to hear your voice if you push it.
INTERCOM FUNCTION 〈Between handset unit and base unit〉 A: Handset Calling Base Unit Handset 1. Press CALL. 2. Press the digit button “0” (means calling the base station) 1 The IN USE indicator will flash alternatively. The IN USE indicator will illuminate during the conversation. 2 Base Unit 1. The base unit will ring six times (bi-bi-bi bi-bi-bi) The INT and Handset No. indicator will flash then light on and pick up the call automatically. B: Base Unit Calling Handset 1.
5. If you have more then one Handset Unit in your network, press the Select button to choose which handset you wish to link with. Press the Select button to move from handset 1, 2, 3, or 4. Once you have selected the handset, press the Int button and only this unit will ring. Use the same procedures to communicate with this unit. Handset Unit 1. Handsets will ring. The indicators of IN USE will flash. This means that the base station is calling. 2. Press any key to begin talking.
person on the Base will take the person off of hold and the call will automatically be transferred to the handset unit. HANDSET UNIT 3. Handset will ring, press any key to talking. 4. Press to deactivate the INT and then press again to get the outside call. 5. You will now be able to answer the call that is on hold. HANDSET AUTODIALING FUNCTIONS Make sure the handset POWER switch is ON. The handset auto-dial memory can store up to 12 telephone numbers. Stored numbers can each have a maximum of 15 digits.
TO ERASE A NUMBER STORED IN THE MEMORY 2 1. Press “MEMO” twice in the standby mode. 2. Press the desired index number ( 0~9, #, * ). The handset will beep and the telephone number assigned to that index number is erased automatically. 1 REDIAL FUNCTION You can redial the last telephone number dialed automatically ( after getting a busy signal, for instance). HANDSET 1. Press to get a dial tone. The TEL indicator and dialing but tons will illuminate. 2. Press REDIAL.
PROGRAMMING A NEW HANDSET INTO THE SYSTEM Setting your handset unit representative number on the Base unit. First, set the POWER switch of the Base and Handset unit to off. BASE UNIT 2 4 1 3 1. Press SEL and without releasing POWER on the Base Unit. 2. All the LED indicators will be displayed and also Indicator NO. 1. 3. Press SEL to change to the Remote Unit No. that you wish to represent either “2”, “3” and “4”. 4. Press the INT button.
OA-2538 HI-GAIN ANTENNA INSTALLATION: NOTE It is essential that the outdoor antenna be placed in a strategic area to provide maximum communication range and clarity. Before the base Station and the Handset unit are activated, be sure to connect the Base Antenna to avoid damage. ATTACHING THE TWO SECTIONS 1. Connect the two middle wires of each section of the antenna together. 2. Use the mini-L wrench to fasten the screw given into the place provided on the middle wire. 3.
COAXIAL CABLE MOUNING 4. Feed the coaxial cable through the support. Mount the high gain antenna on to the support by aligning the holes found on the antenna support with those found on the antenna. Secure the structure by using the screws provided (see illustration). 5. Fix the cable securely using cable clamps and run the cable to the base station unit, then connect it to back.
SIMPLE TROUBLE SHOOTING GUIDE The phone does not work: The AC adaptor may not be plugged into wall outlet. The battery pack may need recharging (if the BATT. LOW indicator is illuminated in the in use mode). The handset may be too far from the base unit. Register the handset on the base unit again. The communication becomes shorter: The handset may need recharging. The base unit or handset antenna may not be extended to this full length.
TECHNICAL INFORMATION This cordless telephone uses radio frequencies to allow mobility. Take note of the following points which could affect operation of your system. 1. NOISE Electrical pulse noise is present in most homes at one time or another. This is most intense during electrical storms. Certain kinds of electrical equipment such as light dimmers, fluorescent bulbs, motors, fans, etc., also generate these noise pulses.
ALCON-73BH BASE UNIT INSTALLATION DIAGRAM 15
